GE L90 Instruction Manual page 151

5 SETTINGS
Table 5–5: L90 FLEXLOGIC™ OPERANDS (Sheet 6 of 7)
OPERAND TYPE OPERAND SYNTAX
INPUTS/OUTPUTS: Cont Ip 1
Contact Inputs Cont Ip 2
↓
Cont Ip 1
Cont Ip 2
↓
INPUTS/OUTPUTS: Cont Op 1
Contact Outputs, Cont Op 2
↓
Current
(from detector on
Cont Op 1
Form-A output only)
Cont Op 2
↓
INPUTS/OUTPUTS: Cont Op 1
Contact Outputs, Cont Op 2
↓
Voltage
(from detector on
Cont Op 1
Form-A output only)
Cont Op 2
↓
INPUTS/OUTPUTS: Direct I/P 1-1 On
↓
Direct Input
Direct I/P 1-8 On
Direct I/P 2-1 On
↓
Direct I/P 2-8 On
INPUTS/OUTPUTS: REMOTE INPUT 1 On
↓
Remote Inputs
REMOTE INPUT 32 On
INPUTS/OUTPUTS: Virt Ip 1
↓
Virtual Inputs
Virt Ip 32
INPUTS/OUTPUTS: Virt Op 1
↓
Virtual Outputs
Virt Op 64
LED TEST LED TEST IN PROGRESS
REMOTE DEVICES REMOTE DEVICE 1 On
↓
REMOTE DEVICE 16 On
REMOTE DEVICE 1 Off
↓
REMOTE DEVICE 16 Off
RESETTING RESET OP
RESET OP (COMMS)
RESET OP (OPERAND)
RESET OP (PUSHBUTTON)
SELF- ANY MAJOR ERROR
DIAGNOSTICS ANY MINOR ERROR
ANY SELF-TEST
BATTERY FAIL
DSP ERROR
EEPROM DATA ERROR
EQUIPMENT MISMATCH
FLEXLOGIC ERR TOKEN
IRIG-B FAILURE
LATCHING OUT ERROR
LOW ON MEMORY
NO DSP INTERRUPTS
PRI ETHERNET FAIL
PROGRAM MEMORY
PROTOTYPE FIRMWARE
REMOTE DEVICE OFF
SEC ETHERNET FAIL
SNTP FAILURE
SYSTEM EXCEPTION
UNIT NOT CALIBRATED
UNIT NOT PROGRAMMED
WATCHDOG ERROR
GE Multilin
OPERAND DESCRIPTION
On (will not appear unless ordered)
On (will not appear unless ordered)
↓
Off (will not appear unless ordered)
Off (will not appear unless ordered)
↓
IOn (will not appear unless ordered)
IOn (will not appear unless ordered)
↓
IOff (will not appear unless ordered)
IOff (will not appear unless ordered)
↓
VOn (will not appear unless ordered)
VOn (will not appear unless ordered)
↓
VOff (will not appear unless ordered)
VOff (will not appear unless ordered)
↓
(appears only when L90 Comm card is used)
↓
(appears only when L90 Comm card is used)
(appears only when L90 Comm card is used)
↓
(appears only when L90 Comm card is used)
Flag is set, logic=1
↓
Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
An LED test has been initiated and has not finished.
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
Reset command is operated (set by all 3 operands below)
Communications source of the reset command
Operand (assigned in the
of the reset command
Reset key (pushbutton) source of the reset command
Any of the major self-test errors generated (major error)
Any of the minor self-test errors generated (minor error)
Any self-test errors generated (generic, any error)
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
L90 Line Differential Relay
5.4 FLEXLOGIC™
!"
INPUTS/OUTPUTS RESETTING
5
menu) source
5-61