Sign In
Upload
Manuals
Brands
WEG Manuals
Controller
SSW-03 plus
WEG SSW-03 plus Manuals
Manuals and User Guides for WEG SSW-03 plus. We have
1
WEG SSW-03 plus manual available for free PDF download: User Manual
WEG SSW-03 plus User Manual (122 pages)
Brand:
WEG
| Category:
Controller
| Size: 4.67 MB
Table of Contents
Table of Contents
4
1 Parameters
8
Quick Parameter References, Error Messages and Status Messages
8
2 Error Messages
11
3 Soft-Starter Status
11
Preliminary Recommendations
12
Safety Notice
12
Safety Notices in the Manual
12
Safety Notices on the Product
12
Introduction
14
About this Manual
14
Version of Software
14
Abbreviations Used
15
About the SSW-03 Plus
15
Introduction
15
Simplified Block Diagram of the SSW-03 Plus
17
Description of the Control Board - CCS 3.0X
18
Product Identification
19
Receiving
19
Installation
20
Mechanical Installation
20
Environment
20
Location/Mounting
21
Kit IP20
23
Connections Within the Motor Delta Connection
25
Electrical Installation
26
Power/Grounding Connections
26
Location of the Power/Grounding/ Fans Connection
33
Signal and Control Connections
33
Description of the X2 Connector
34
Fan Connections
35
Combination Drive "A" Operation by HMI, Standard Connection
36
Combination Drive "B" Operation through Terminals, Standard Connection
38
Combination Drive "C" Operation through Terminals, Connection Within the Motor Delta Connection
39
Installation of Optional Devices
41
HMI-3P on the Panel Door
41
Mechanical Installation
41
Electrical Installation
42
Power-Up
43
Power-Up Preparation
43
Power-Up/Commissioning
43
Commissioning
44
Preparation
45
Hmi-3P
45
Commissioning and Operation Via Terminals
46
Settings During the Commissioning
47
Description of the HMI-3P Interface
49
Use of the Hmi
49
Use of the HMI-3P
50
Use of the HMI-3P for Operation
50
(Display)
51
Parameter Changing
54
Selection/Changing Parameters
55
Detailed Parameter Description
57
Standard Parameter Set at Factory
57
Read Parameters - P71
58
P71 - Software Version
58
P72 - Motor Current %I N
58
P73 - Motor Current (A)
58
P74 - Active Power
58
P75 - Apparent Power
58
P76 - Load Power Factor
58
P77 - Output Voltage
58
P82 - Motor Thermal Protection Status
58
Last Errors
59
Regulation Parameters P00
59
P00-Parameter Access
59
P01- Initial Voltage
59
P02 - Time of the Acceleration Ramp
60
P03 - Voltage Fall Step During Deceleration
60
P04 - Time of the Deceleration Ramp
61
P11 - Current Limitation
61
P12 - Immediate Overcurrent
63
P14 - Immediate Undercurrent
64
P13 - Immediate Overcurrent Time
65
P15 - Immediate Undercurrent Time
65
P22 - Rated Current of the Soft-Starter
65
P23 - Rated Voltage of the Soft-Starter
66
P31 - Phase Rotation
66
P33 - Voltage Level of the JOG Function
67
P34 - DC Breaking Time
67
DC-Braking Voltage Level (%UN)
68
17P36 - Time Interval between Starts
68
P35 - DC-Braking Voltage Level (%UN)
68
P41 - Voltage Pulse Time at the Start
69
P42 - Voltage Pulse Level at the Start
70
P45 - Pump Control
70
P47 - Auto-Reset Time
72
Configuration Parameters P28, P43, P44, P46, P50
72
P28 - Operation Mode
72
P43 - By-Pass Relay
75
P44 - Energy Save
76
P46 - Default Values (It Loads Factory Parameters)
76
P50 - Function of the Relay RL3
77
P51 - Function of the Relay RL1
77
P52 - Function of the Relay RL2
78
P53 - Programming of the Digital Input 2
79
P54 - Programming of the Digital Input
80
P55 - Programming of the Digital Input 4
80
P56 - Programming of the Analog Output
81
P57 - Scaling of the Analog Output
81
P61 - Control Enabling
82
P62 - Address of the Soft-Starter at the Communication Network
83
P63 - Watch Dog Time of the Serial Communication
84
P64 - Action after Watch Dog Time Is Elapsed
84
Motor Parameters
85
P21 - Motor Current Setting of the Switch)
85
P25 - Thermal Class of the Motor Protection
86
P26 - Motor Service Factor
90
P27 - Auto-Reset of the Thermal Motor Image
91
Maintenance
92
Errors and Possible Causes
92
Programming Error (E24)
92
Serial
92
Hardware Errors (E0X)
92
MAINTENANCE 7.1 Errors and Possible Causes
92
Preventive Maintenance
96
Cleaning Instructions
97
Changing Supply Fuse
97
Spare Part List
98
Power / Current Table
100
Table of Power and Currents for
100
6 Cable Connection with in Motor Delta Connection (Ambient Temperature of 55°C (131°F))
101
Power Data
100
Technical Characteristics
100
Electronics Data
102
Electronics Data/General
102
Mechanical Data
102
Appendix
104
EMC and LVD Directives
104
Requirements for Conforming
104
Installations
104
Recommended Application with Terminals for Two Wire Control
106
Recommended Application with Terminals for Three Wire Control
107
Recommended Application with Terminals for Three Wire Control and Power Isolation Contactor
108
Recommended Application with Terminals for Three Wire Control and By-Pass Contactor
109
Recommended Application with Terminals for Three Wire Control and DC Braking
110
Recommended Application with Terminals for Three Wire Control and Motor Speed Reversal
111
Recommended Applications with PC or PLC Command
112
Recommended Application with Control by
113
Delta Connection of the 6 Cable Motor
113
Contactor and Connection Within the Motor Delta Connection of the 6 Cable Motor
113
Recommended Drive with Control by Three-Wire Digital Inputs, with By-Pass Contactor and Connection Within the Motor Delta Connection of the Motor with 6 Cables
115
Recommended Application with Terminals for Three Wire Control for Several Motors
116
Symbols
118
Optinal Devices
121
Recommended Drive with Control by Digital Inputs with Three Wires and Bypass Contactor + MAC-0X
121
Fieldbus Communication
122
Superdrive
122
Advertisement
Advertisement
Related Products
WEG SSW-03 Plus Series
WEG SSW-08
WEG SSW-06.0412
WEG SSW-06.0130
WEG SSW-05
WEG SSW-05.10
WEG SSW-05.23
WEG SSW-05.45
WEG SSW-05.16
WEG SSW-05.3
WEG Categories
DC Drives
Controller
Circuit breakers
Control Unit
Inverter
More WEG Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL