User Manuals: Tektronix Keithley 4200-SMU Measure Unit

Manuals and User Guides for Tektronix Keithley 4200-SMU Measure Unit. We have 1 Tektronix Keithley 4200-SMU Measure Unit manual available for free PDF download: User Manual

Tektronix Keithley 4200-SMU User Manual

Tektronix Keithley 4200-SMU User Manual (130 pages)

Source-Measure Unit

Brand: Tektronix | Category: Measuring Instruments | Size: 5 MB

Table of Contents

Table of Contents
6
Introduction

10
- Source-Measure Unit (SMU)
  10
- Preamplifier
  11
- Ground Unit (GNDU)
  11
Connections and Configuration

12
- Basic Source-Measure Connections
  12
- Test Fixture and Device under Test (DUT) Connections
  31
Setting up Smus in Clarius

34
- Introduction
  34
- Set up a Simple Project
  34
  - Select Project Components
    34
  - Add a Device and Test to the Project
    35
- Configure a Simple Test
  36
  - Set the Key Parameters
    38
  - Set the Test Parameters
    39
- Run a Simple Test
  41
- Operation Mode (SMU)
  42
- SMU - All Terminal Parameters
  49
  - Base Current
    49
  - Base Voltage
    49
  - Bias
    49
  - Column Name (Measure Current)
    50
  - Column Name (Measure Voltage)
    50
  - Compliance
    50
  - Dual Sweep
    51
  - Force Range (Source Range)
    52
  - List Values
    52
  - Low Range
    52
  - Measure Current
    52
  - Off Time
    52
  - On Time
    53
  - Overvoltage Protection
    53
  - Points (List or Segment Sweep)
    53
  - Points (Log Sweep)
    53
  - Points
    54
  - Power on Delay
    54
  - Pulse Mode
    54
  - Range (Measure Current)
    56
  - Report Status (SMU)
    57
  - Report Value (Measure Current or Report Current)
    57
  - Report Value (Report Voltage or Measure Voltage)
    57
  - Segments
    57
  - Start (Step)
    58
  - Start (Sweep)
    58
  - Step (Step)
    58
  - Step (Voltage Sweep)
    59
  - Stop (Step)
    60
  - Stop (Sweep)
    60
  - Voltage (Report Voltage)
    60
  - Voltage Range
    60
- SMU Test Settings
  60
  - Speed
    60
  - Report Timestamps
    61
  - Delay Factor
    62
  - Filter Factor
    63
  - Auto A/D Aperture
    64
  - A/D Aperture Time
    64
  - Test Mode
    64
  - Sweep Delay
    65
  - Interval
    65
  - Number of Samples
    65
  - Hold Time - SMU
    65
  - SMU Power on Sequence
    65
  - Disable Outputs at Completion - SMU
    66
  - Output Values
    66
  - Compliance Exit-Condition Options
    67
Source-Measure Hardware

68
- Source-Measure Units
  68
- Source-Measure Hardware Overview
  68
- Basic SMU Circuit Configuration
  69
- Source-Measure Hardware Overview
  69
- SMU Terminals and Connectors
  70
  - SENSE lo Terminal
    71
  - SENSE Terminal
    72
  - FORCE Terminal
    72
  - PA CNTRL Connector
    72
- Source-Measure Unit (SMU) with 4200-PA Overview
  72
- Ground Unit (GNDU) Overview
  79
  - Basic Characteristics
    79
  - Ground Unit Connections
    80
  - Ground Unit DUT Connections
    81
  - Ground Unit Terminals and Connectors
    82
  - FORCE Terminal
    82
  - SENSE Terminal
    83
  - COMMON Terminal
    83
Source-Measure Concepts

84
- Guarding
  84
  - Guard Connections
    85
  - Source-Measure Concepts
    85
  - Guarding Concepts
    86
  - Test Fixture Guarding
    87
- Local and Remote Sensing
  88
  - Local Sensing
    90
  - Remote Sensing
    91
- Source or Sink
  91
- Source-Measure Considerations
  95
  - Source I, Measure V or I
    95
  - Source V, Measure I or V
    96
  - Measure Only (V or I)
    97
  - I-Source Operating Boundaries
    98
  - I-Source Operation Examples
    99
  - V-Source Operating Boundaries
    100
  - V-Source Operation Examples
    101
  - Source I Measure I and Source V Measure V
    102
- Sweep Concepts
  102
  - Source-Delay-Measure Cycle
    103
  - Sweep Waveforms
    103
- Operation Mode Timing
  105
  - Sampling Mode Timing
    106
Optimizing SMU Measurements

108
- Introduction
  108
- Making Stable Measurements with Smus
  108
- Low-Current Measurements
  111
  - Leakage Currents
    112
  - Generated Currents
    112
  - Voltage Burden
    115
  - Noise and Source Impedance
    116
  - Cable Capacitance
    117
  - Test System Performance
    117
- Interference
  118
Make I-V Measurements on a Solar Cell

120
- Introduction
  120
- Equipment Required
  120
- Device Connections
  121
  - Device Connection Schematic
    121
  - Connect the 4200A-SCS to the DUT
    122
- Setting up Measurements in the Clarius Software
  123
  - Create a New Project
    123
  - Search for and Select a Test
    124
  - Configure the Test
    125
  - Run the Test
    127
  - Analyze the Test Results
    128
  - Additional Tests
    129

Advertisement

Advertisement

Related Products

Tektronix Categories

Test Equipment Measuring Instruments Amplifier Portable Generator

Printer

More Tektronix Manuals