Summa SummaSign Pro D1010 SL Manuals

Manuals and User Guides for Summa SummaSign Pro D1010 SL. We have 1 Summa SummaSign Pro D1010 SL manual available for free PDF download: User Manual

Summa SummaSign Pro D1010 SL User Manual

Summa SummaSign Pro D1010 SL User Manual (71 pages)

Brand: Summa | Category: Cutter | Size: 0 MB

Table of Contents

Table of Contents
5
1 General Information

10
- Introduction
  10
- Product Features
  11
- Summasign Pro Sl D-Series User Manual
  12
- Specifications
  13
- Cutter
  13
- Media
  13
- Summasign Pro Sl D-Series Cutter Specifications
  13
- Summasign Pro Sl D-Series Media Specifications
  13
- Knife, Pen and Pouncing Tool
  15
- Interface
  15
- Summasign Pro Sl D-Series Knives, Pens and Pouncing Tools
  15
- Summasign Pro Sl D-Series Interface Specifications
  15
- Firmware
  16
- Performance
  16
- Certifications
  16
- Summasign Pro Sl D-Series Firmware
  16
- Summasign Pro Sl D-Series Performances
  16
- Environmental
  17
- Electrical
  17
- Summasign Pro Sl D-Series Environmental Specifications
  17
- Summasign Pro Sl D-Series Electrical Specifications
  17
- Cutter Accessories and Consumables
  18
- Summasign Pro Sl D-Series Accessories and Consumables
  18
- Rear Panel Components
  19
- Front Panel Controls
  21
- Powering up the Cutter
  23
- Earthing
  23
- Installation of a Knife, Pen or Pouncing Tool
  25
- Knife Installation
  25
- Pen Installation
  28
- Installation of the Pouncing Tool
  29
- Loading Media
  30
- Positioning the Pinch Rollers
  30
- Feeding and Positioning Media
  31
- Media Load Procedure
  35
Section 2

38
2 Operation

38
- The Control Panel
  38
- The Liquid Crystal Display
  39
- The Reset/Load Key
  39
- The Online Key
  40
- The Menu Key
  40
- The Enter Key
  42
- The 1 and 2 Keys 1 - 2
  42
- The Jogging Keys
  42
- The Tool Up/Down Key
  42
- The Tool Select Key
  42
- Normal Operation
  44
- Online and Offline
  44
- Local Operation
  45
- The User Config Menu
  46
- Knife Pressure
  47
- Knife Offset
  48
- Pouncing Pressure
  48
- Velocity
  48
- Overcut
  49
- Pouncing Gap
  49
- System Setup
  49
- System Setup
  50
- Concatenation
  50
- Smoothing
  50
- Emulate
  50
- Tool
  51
- Menu Units
  51
- Addressing
  51
- Baud Rate
  51
- Parity
  52
- Rts/Dtr
  52
- DM/Pl Errors
  53
- Hp-Gl Errors
  53
- Hp-Gl Origin
  53
- Media Sensor
  54
- Autoload
  54
- Tool Command
  54
- Load on W CMD
  54
- Flex-Cut
  55
- Recut Offset
  55
- Internal Test Menu
  56
- Cut Border
  57
- Menu Plot
  57
- Confidence Cut
  57
- Din Cut
  57
- Cal. Media
  58
- Calibration Opos
  58
- Opos Settings
  58
- System Tests
  58
- System Tests
  59
- Language
  59
- Rom Revision
  59
- Service Plot
  59
- Optical Sensor
  60
- Sensor Setup
  60
- Rs232 Test
  60
- Ram Test
  61
- Install Menu
  61
- Coil Setup
  61
- Lcd Contrast
  61
3 General Information

62
- Maintenance & Cleaning
  62
- Cleaning the Drive System
  62
- Cleaning the Sensors
  63
- Operating Voltage Conversion
  64
Section 4

65
4 Interface

65
- Introduction
  65
- Rs232 Interface Notes
  65
- System Setup
  65
- Serial Interface Connector on the Cutter
  66
- Available Serial Signals
  66
- Usb Interface Notes
  67
- Usb Specifications
  67
- Installing the Usb Software under Windows
  67
- Installing the Usb Software for Your Macintosh
  68
- Parallel Interface Connector on Cutter
  69
5 Media Certification

70

Advertisement

Advertisement

Related Products

Summa Categories

Printer

Printer Label Maker Power Tool Accessories

More Summa Manuals