Rohde & Schwarz RTM2034 Manuals

Manuals and User Guides for Rohde & Schwarz RTM2034. We have 1 Rohde & Schwarz RTM2034 manual available for free PDF download: User Manual

Rohde & Schwarz RTM2034 User Manual

Rohde & Schwarz RTM2034 User Manual (499 pages)

Digital Oscilloscope

Brand: Rohde & Schwarz | Category: Test Equipment | Size: 7 MB

Table of Contents

Table of Contents

18
- 1 Preface
  
  24
- 2 Acquisition and Waveform Setup
  
  26
  - Basics
    26
  - Vertical System
    26
  - Sampling and Acquisition
    27
  - Horizontal System
    30
  - Probes
    31
    
    Setting up the Waveform
    35
  - Adjusting the Signal Input Manually
    35
  - Setting up the Signal Input with Autoset
    35
  - Setting the Acquisition
    36
  - Starting and Stopping Acquisition
    36
    
    Reference for Waveform Setup
    37
  - HORIZONTAL Controls
    37
  - Acquisition Menu
    38
Decimation Mode/Arithmetic

39
- Arithmetic
  39
- Decimation Mode
  39
- Limit Freq
  40
- No. of Averages
  40
- Nx Single
  40
- Waveform Rate
  40
- Record Length
  41
- Roll
  41
- Sample Mode
  41
- Vertical Settings
  42
  - Interpolation
    42
  - Basics of Triggering
    51
  - Setting up the Trigger
    52
- 3 Triggers
  
  51
  - Configuring the Trigger Event
    52
  - Positioning the Trigger
    53
  - Setting up a Trigger Sequence
    53
    
    Reference for Triggers
    54
  - TRIGGER Controls
    54
  - Trigger Settings
    55
- 4 Display
  
  69
  - General Display Settings
    69
  - Configuring the Display
    70
4.1.2 Display Menu

72
- Display Menu
  72
  - Backlight
    73
  - Display Mode
    73
  - Intensities
    73
  - Waveform
    73
  - XYZ Setup
    73
  - Clear Persist
    74
  - Dots Only
    74
  - Grid
    74
  - Inverse Brightn
    74
  - Persist. Time
    74
  - Persistence
    74
  - Aux. Cursors
    75
  - Channel Cursors
    75
  - Colors
    75
  - Trigger Event
    75
  - Trigger Hyst
    76
  - XY-Diagram
    76
- Configuring XY-Diagrams
  77
- XYZ Setup Menu
  79
  - Zoom
    81
- Zoom Display
  81
- Zooming for Details
  83
- Zoom Menu
  84
  - Markers
    86
- Using Timestamp Markers
  86
- Reference for Markers
  88
- 5 Reference Waveforms
  
  89
  - Displaying a Reference Waveform
    89
  - Using References
    89
  - Saving and Loading References
    90
    
    Reference for REF Key
    91
    
    Cursor Measurements
    93
- 6 Measurements
  
  93
Cursor/Meas.type

98
- Cursor
  98
- Meas.type
  98
- Source
  98
- Coupling
  99
- Prev. Peak
  99
- Set to Screen
  99
- Set to Wave
  99
- Track Scaling
  99
- Navigation
  100
- Next Peak
  100
- Quick Measurements
  100
6.3 Automatic Measurements

102
- Automatic Measurements
  102
- Measurement Types and Results
  102
  - Measurement Types
    102
  - RMS Value
    103
  - Mean Cycle
    103
  - RMS Cycle
    103
  - Peak Peak
    103
  - Frequency
    103
  - Crest Factor
    104
  - Top Level
    104
  - Base Level
    104
  - Pos. Overshoot
    104
  - Neg. Overshoot
    104
- Configuring and Performing Automatic Measurements
  108
- Auto Measure Menu (MEAS Key)
  109
- 7 Mathematics
  113
7.2 Reference for Mathematics

116
- Reference for Mathematics
  116
- Equation
  117
- Unit
  117
- Visible
  117
- Edit Equations
  118
  - Equation
    118
  - Operator
    118
  - Operand 1
    122
  - Operand 2
    123
  - Edit Constant
    123
    
    Constant
    123
    
    Decimal Point
    123
    
    Prefix
    123
    
    Value
    123
    
    Save
    124
    
    Unit
    124
    
    FFT Display
    125
    
    Configuring and Using FFT Calculations
    126
- 8 Fft
  125
  - Setting up the FFT Analysis
    126
  - Configuring the Diagrams
    127
  - Measuring on FFT
    130
    
    Reference for FFT Key
    130
Fft/Wfm. Arithmetic

131
- Fft
  131
- Wfm. Arithmetic
  131
- No. of Averages
  132
- Window
  132
- FFT-Setup
  133
  - Span
    134
  - Center
    134
  - Y-Scale
    134
  - YT-Window
    134
  - Position
    135
  - Points
    135
- Y-Scaling
  133
- Y(T)-Setup
  135
  - Y-Scale
    135
  - Y-Position
    135
  - Main Time Base
    135
  - Trigger Offset
    136
  - Show Channels
    136
- Fft
  136
- FFT off
  136
- 9 Masks
  137
  - About Masks
    137
  - Mask Testing
    137
  - File Formats for Masks
    138
    
    Working with Masks
    139
  - Creating New Masks
    140
  - Loading Masks
    142
  - Performing a Mask Test
    142
9.3 Reference for Masks Key

143
- Reference for MASKS Key
  143
- Test
  143
- New Mask
  144
  - Copy Channel
    144
  - Stretch y
    144
  - Width y
    144
  - Y-Position
    144
  - Save
    145
  - Width X
    145
- Pause
  144
- Actions
  145
  - Sound, Stop, Screenshot, Print, Waveform
    146
- Load Mask
  145
- Masks Test off
  146
- 10 Search
  
  147
  - Search Conditions and Results
    147
  - Search Results
    147
    
    Configuring and Performing Searches
    149
    
    Reference for Search Menu
    150
  - Main Search Menu
    150
  - Edge Setup
    152
  - Width Setup
    153
  - Peak Setup
    154
  - Rise/Fall Time Setup
    154
  - Runt Setup
    156
  - Data2Clock Search
    157
  - Pattern Search
    159
  - Gate Menu
    161
  - Events Menu
    162
- 11 Protocol Analysis
  
  163
  - Basics of Protocol Analysis
    163
  - Configuring Common Protocol Settings
    163
  - Protocol - Common Settings
    164
  - Display Settings
    165
  - Label List
    166
  - Frame Table: Decode Results
    169
    
    SPI/SSPI Bus (Option R&S RTM-K1)
    170
  - The SPI Protocol
    170
  - SPI/SSPI Bus Configuration
    171
  - SPI/SSPI Trigger
    174
  - SPI/SSPI Decode Results
    177
    
    I²C (Option R&S RTM-K1)
    180
  - The I²C Protocol
    180
  - I²C Configuration
    182
  - I²C Trigger
    183
  - I 2 C Label List
    187
  - I 2 C Decode Results
    188
    
    UART/RS-232 Interface (Option R&S RTM-K2)
    190
  - The UART / RS232 Interface
    190
  - UART/RS-232 Configuration
    191
  - UART/RS-232 Trigger
    194
  - UART/RS-232 Decode Results
    198
    
    CAN (Option R&S RTM-K3)
    200
  - CAN Configuration
    200
  - CAN Trigger Settings
    201
  - CAN Label List
    206
  - CAN Decode Results
    207
  - Search on Decoded CAN Data
    209
    
    LIN (Option R&S RTM-K3)
    212
  - The LIN Protocol
    212
  - LIN Configuration Settings
    213
  - LIN Trigger Settings
    214
  - LIN Label List
    217
  - LIN Decode Results
    218
  - Search on Decoded LIN Data
    220
- 12 Mixed Signal Option (MSO, R&S RTM-B1)
  
  223
  - About MSO
    223
  - Digital Channels
    224
  - Digital Channels - Configuration Settings
    224
    
    Parallel Buses
    226
  - Analyzing Parallel Buses
    226
  - Parallel Clocked Bus
    227
  - Parallel Bus (Unclocked)
    228
- 13 Data and File Management
  
  230
  - Printing
    230
  - Printing a Screenshot
    230
  - Printer Settings
    231
    
    Saving and Loading
    232
  - Storage Locations
    232
  - Quick Access with PRINT Key
    238
  - Device Settings
    240
  - Waveforms
    242
  - Screenshots
    245
  - References, Masks, and Equation Sets: Import/Export
    247
- 14 General Instrument Setup
  
  248
  - Firmware and Options
    248
  - Updating Firmware
    248
  - Activating Options
    249
    
    Reference for Setup
    249
Table of Contents

250
- Default
  252
- Device Information
  252
- Down
  252
- Save
  252
- Update
  252
  - Firmware
    252
    
    Execute
    252
  - Interface
    253
    
    Execute
    253
  - Upgrade
    253
    
    Input Key Manually
    253
    
    Read Keys from License File
    253
- Printer
  253
- Sound
  253
  - Control Beep
    253
  - Error Beep
    253
  - Trigger Beep
    253
- Probe Adjust
  254
  - 1Khz
    254
  - 1Mhz
    254
  - Automatic
    255
- Self Alignment
  254
  - Self Test & Self Alignment
    254
  - Start
    254
  - Abort
    254
  - Log File
    254
- Device Name
  255
- LED Intensity
  255
- Secure Erase
  255
- Trigger Output
  255
  - Output
    255
  - Polarity
    255
  - Pulse Width
    255
  - Basics
    256
- 15 Remote Control
  256
  - Remote Control Interfaces
    256
  - Setting up a LAN Connection
    258
    
    Messages and Command Structure
    263
    
    Switching to Remote Control
    263
    
    Command Sequence and Synchronization
    274
    
    Status Reporting System
    276
    
    General Programming Recommendations
    287
    
    Command Reference
    288
    
    Conventions Used in Remote Command Description
    288
    
    Common Commands
    289
    
    General Remote Settings and Queries
    292
    
    Acquisition and Setup
    296
    
    Trigger
    316
    
    Display
    329
    
    Reference Waveforms
    337
    
    Measurements
    341
    
    Mathematics
    360
  - Fft
    363
  - Masks
    369
  - Search
    373
  - Protocol Analysis
    389
  - Mixed Signal Option (MSO, R&S RTM-B1)
    449
  - Data and File Management
    456
  - General Instrument Setup
    465
  - Status Reporting
    468
    
    Data Export
    473
    
    Programming Examples
    473
    
    Search
    475
    
    Data and File Management
    476
    
    List of Commands
    478
    
    Index
    491

Advertisement

Advertisement

Related Products

Rohde & Schwarz Categories

Measuring Instruments Test Equipment Portable Generator

Power Supply

Power Supply Accessories

More Rohde & Schwarz Manuals