MPE DP SERIES II Manuals

Manuals and User Guides for MPE DP SERIES II. We have 1 MPE DP SERIES II manual available for free PDF download: Operating And Service Manual

MPE DP SERIES II Operating And Service Manual

MPE DP SERIES II Operating And Service Manual (145 pages)

DC

Brand: MPE | Category: Power Supply | Size: 2 MB

Table of Contents

Table of Contents
9
1 General Information

14
- Description
  14
- Features
  14
- IEC Symbols Used in Manual
  17
- Power Requirements
  17
- Specifications
  18
2 Installation and Power on Check

30
- Cooling
  30
  - Air Cooling
    30
  - Water Cooling
    30
- AC Input Connections
  31
- DC Output Connections
  31
- General Operation
  33
- Controls and Indicators
  33
- Preparation for Use
  34
  - Unpacking
    34
  - Electrical Check
    34
    
    DPD Series Models
    34
    
    DPA Series Models
    35
    
    DPC Series Models
    36
3 Operation

40
- Front Panel Commands
  40
  - DPD Series Front Panel Commands
    40
    
    Run Mode Commands
    40
    
    Set Point Commands
    42
    
    Configuration Commands
    43
    
    Calibration Commands
    51
    
    Programming Sequential Step Applications
    52
  - DPA Series Front Panel Commands
    54
    
    Run Mode Commands
    54
    
    Configuration Commands
    55
    
    Calibration Commands
    58
- Modes of Operation
  60
  - Normal Mode
    60
  - Constant Voltage
    60
  - Constant Current
    60
- Remote Sensing
  62
- External Programming
  62
  - Resistive Programming
    62
  - Voltage Programming
    65
  - Current Programming
    65
- Voltage and Current Monitoring
  66
- Digital Input and Output Lines
  67
- Diagnostic Functions
  67
- Parallel Operation
  70
- Series Operation
  70
  - Series Operation - Direct
    70
  - Series Operation - Master/Slave
    70
- Pulse Loading
  71
- Nomenclature
  72
4 Programming with Scpi Commands

76
- Command Features
  76
- Electrical Testing Using RS232 Communications
  76
- SCPI Subsystem Commands
  77
  - Source Subsystem
    77
    
    VOLT and VOLT:TRIG
    78
    
    Volt:prot
    79
    
    CURR and CURR:TRIG
    80
    
    Curr:prot
    80
    
    PER (DPD Series Only)
    81
  - Measure Subsystem
    82
    
    Meas:volt
    82
    
    Meas:curr
    82
  - System Subsystem
    82
    
    Syst:vers
    82
    
    Syst:err
    82
  - Status Subsystem
    83
    
    Operation Register
    83
    
    Questionable Register
    84
  - Output Subsystem
    84
    
    Outp
    85
    
    OUTP:ARM (DPD Series Only)
    85
    
    Outp:start
    86
    
    Outp:stop
    86
    
    Outp:prot:cle
    86
  - Abort Subsystem
    87
  - Trigger Subsystem
    87
  - Initiate Subsystem
    87
  - Calibrate Subsystem
    88
    
    Cal:idn
    88
    
    Cal:pass
    89
    
    Cal:pot
    89
    
    Cal:scal:volt
    89
    
    Cal:scal:curr
    90
    
    Cal:scal:inp
    90
    
    Cal:def
    90
    
    Cal:stop
    91
  - Configure Subsystem
    91
    
    Rem:sens
    91
    
    Cont:int
    92
    
    Cont:ext
    92
    
    Inte
    92
    
    Conf:setpt
    93
  - GPIB Communications Subsystem
    93
    
    GPIB:VERS? (Optional GPIB Only)
    93
    
    GPIB:ADDR (Optional GPIB Only)
    94
  - Ethernet Communications Subsystem
    94
    
    NET:VERS? (Optional Ethernet Only)
    94
    
    NET:MAC? (Optional Ethernet Only)
    94
    
    NET:SER? (Optional Ethernet Only)
    95
    
    NET:ADDR (Optional Ethernet Only)
    95
    
    NET:GATE (Optional Ethernet Only)
    96
    
    NET:SUBN (Optional Ethernet Only)
    96
    
    NET:PORT (Optional Ethernet Only)
    97
    
    NET:HOST? (Optional Ethernet Only)
    97
    
    NET:DHCP (Optional Ethernet Only)
    97
  - Recall Subsystem (DPD Series Only)
    98
  - Modulation Subsystem (DPD Series Only)
    98
    
    Mod:type:sel
    98
    
    Mod:save
    100
    
    Mod:tabl:load
    101
  - SCPI Data Formats
    101
- IEEE-488 Event Processing
  102
- IEEE-488 Standard Commands
  102
  - Clear
    102
  - Read Event Status Register
    102
  - Read and Set Event Status Enable Register
    104
  - Read Status Byte Register
    105
  - Read and Set Service Request Enable Register
    105
  - Read Model Number, Part Number, and Serial Number
    106
  - Save
    106
  - Recall
    107
  - Reset
    107
- Error Messages
  108
- Restricted Command Set
  109
5 Interfacing Using the Remote Interface Software

112
- Application Setup
  112
- Virtual Control Panel
  112
- Command Panel
  114
- Register Panel
  114
- Calibration Panel
  116
- Firmware Panel
  117
- Modulation Panel (D Version Front Panels Only)
  117
6 Principle of Operation

120
- General
  120
- Master Module
  120
- Slave Module
  122
7 Maintenance and Trouble Shooting

123
- General
  123
- Trouble Shooting Guide
  123
- Calibration
  124
  - Control Board
    124
    
    Reference Amplifier Calibration
    124
    
    Voltage Feedback Amplifier Calibration
    124
    
    Current Feedback Amplifier Calibration
    124
  - Driver Board
    125
    
    Over Current Protection
    125
    
    Under Voltage Protection
    125
8 Applications

126
- General
  126
- Power Waveform Generator
  126
- Leadless Remote Sensing
  127
- Photovoltaic Cell Simulator
  127
- Battery Charger
  129
Appendix A Ieee-488 Communications

133
- IEEE-488 Communications Using the Remote Interface Software
  133
- IEEE-488 Communications with MAX
  133
Appendix B Ethernet Communications

135
- Ethernet Communications Using the Remote Interface Software
  135
- Ethernet Communications Using Hyperterminal
  135
  - Connectivity
    136
  - B.3 Ethernet Communications Using a Web Page Browser
    136
  - Discovery
    137
    
    Discovery Using ni Measurement & Automation Explorer
    137
    
    Discovery Using Agilent Connection Expert
    137
    
    Discovery Using the Remote Interface Software
    137
  - Web Interface
    137
Appendix C Usb Communications

141
- Edgeport/1 Setup
  141
- Edgeport/1 Communications Using the Remote Interface Software
  141
Appendix D Rs485 Communications

142
- 485DSS Initial Setup
  142
- Hyperterminal Setup
  142
- 485DSS Address Command
  143
- 485DSS Communications Using Hyperterminal
  143

Advertisement

Advertisement

Related Products

MPE Categories

Controller Speakers

Power Supply

Power Supply Coffee Grinder Relays

More MPE Manuals