User Manuals: ITech IT7634 Programmable Power Supply

Manuals and User Guides for ITech IT7634 Programmable Power Supply. We have 1 ITech IT7634 Programmable Power Supply manual available for free PDF download: Programming Manual

ITech IT7634 Programming Manual

ITech IT7634 Programming Manual (103 pages)

Brand: ITech | Category: Power Supply | Size: 1 MB

Table of Contents

Limitation of Warranty
3
Safety Symbols
3
Environmental Conditions
5
Regulatory Markings
5
Waste Electrical and Electronic Equipment ( WEEE) Directive
5
Compliance Information
7
Table of Contents
8
Chapter1 SCPI Introduction

14
- 1.1 Overview
  14
- 1.2 Command Type of SCPI
  14
- 1.3 Message Type of SCPI
  16
- 1.4 Response Data Type
  18
- 1.5 Command Format
  19
- 1.6 Data Type
  21
- 1.7 Remote Interface Connections
  22
Chapter2 System Commands

23
- Status:questionable[:Event]
  23
- Status:questionable:enable
  23
- Status:questionable:ptransition
  24
- Status:questionable:ntransition
  24
- Status:questionable:condition
  25
- Status:operation[:Event]
  25
- Status:operation:enable
  26
- Status:operation:ptransition
  26
- Status:operation:ntransition
  27
- Status:operation:condition
  27
- System:beeper:immediate
  27
- System:beeper[:State]
  28
- System:version
  28
- System:error
  28
- System:clear
  29
- System:remote
  29
- System:local
  29
- System:rwlock
  30
- System:date
  30
- System:time
  31
- System:communicate:gpib[:Self]:Address
  31
- System:communicate:lan:current:address
  32
- System:communicate:lan:current:dgateway
  32
- System:communicate:lan:current:smask
  32
- System:communicate:lan:dhcp[:State]
  33
- System:communicate:lan:socketport
  33
- System:communicate:lan:macaddress
  34
- System:communicate:select
  34
- System:communicate:serial:baudrate
  35
- System:backlight:brightness
  35
- System:posetup
  35
- System:device:num
  36
- System:measure:mode
  36
- System:source:mode
  37
- System:trig:source
  37
- System:run:network
  37
- System:run:devnum
  38
- System:run:grpnum
  38
Chapter3 Measurement Commands

39
- Fetch[:Scalar]:Voltage
  39
- Fetch[:Scalar]:Current
  39
- Fetch[:Scalar]:Power[:Real]
  39
- Fetch[:Scalar]:Power:apparent
  39
- Fetch[:Scalar]:Power:pfactor
  40
- Fetch[:Scalar]:Frequency
  40
- Fetch[:Scalar]:Cfactor
  40
- Fetch[:Scalar]:Current:peak:plus
  41
- Fetch[:Scalar]:Current:peak:minus
  41
- Fetch[:Scalar]:Current:isurge
  41
- Measure[:Scalar]:Voltage
  41
- Measure[:Scalar]:Current
  42
- Measure[:Scalar]:Power[:Real]
  42
- Measure[:Scalar]:Power:apparent
  42
- Measure[:Scalar]:Power:pfactor
  43
- Measure[:Scalar]:Frequency
  43
- Measure[:Scalar]:Cfactor
  43
- Measure[:Scalar]:Current:peak:plus
  43
- Measure[:Scalar]:Current:peak:minus
  44
- Measure[:Scalar]:Current:isurge
  44
- Fetch
  44
- Measure
  45
Chapter4 Vector Commands

46
- Vector:order
  46
- Vector:data
  46
- Vector:type
  47
Chapter5 Harmonic Commands

48
Chapter6 Oscilloscope Commands

52
- Wave:trigger:mode
  52
- Wave:trigger:slope
  52
- Wave:trigger:slope
  53
- Wave:trigger:source
  53
- Wave:trigger:voltage[:Level]
  53
- Wave:trigger:voltage[:Level]
  54
- Wave:trigger:current[:Level]
  54
- Wave:trigger:current[:Level]
  55
- Wave:trigger:delay:time
  55
- Wave:voltage:data[:Normalization]
  56
- Wave:current:data[:Normalization]
  56
- Wave:auto
  56
- Wave:single
  57
- Wave:run
  57
- Wave:stop
  57
- Wave:trigger[:State]
  57
- Wave:scope:divtime
  58
- Wave:scope:selection
  58
- Wave:scope:selection
  59
- Wave:knob:selection
  59
- Wave:voltage:base
  60
- Wave:current:base
  60
- Wave:current:base
  61
- Wave:voltage:range
  61
- Wave:voltage:range
  62
- Wave:current:range
  62
- Wave:addr
  63
Chapter7 Self-Defined Wave Commands

64
- Selfdefine:name
  64
- Selfdefine:recall:name
  64
- Selfdefine:save
  64
- Selfdefine:data
  64
- Selfdefine:recall
  65
- Selfdefine:recall:num
  65
Chapter8 Output Commands

66
Chapter9 STEP Commands

77
- Step:voltage:start
  77
- Step:voltage:stop
  77
- Step:voltage:stop
  78
- Step:voltage:interval
  78
- Step:mode
  79
- Step:freq:start
  79
- Step:freq:start
  80
- Step:freq:stop
  80
- Step:freq:interval
  80
- Step:freq:interval
  81
- Step:time:interval
  81
- Step:priority<Volt|Freq
  82
- Step:priority
  82
- Step:repetition
  83
Chapter10 Protection Commands

84
- Protect:rms:current
  84
- Protect:rms:time
  84
- Protect:rms:time
  85
- Protect:rms:ctr
  85
- Protect:rms:ctr
  86
- Protect:peak:current
  86
- Protect:peak:time
  87
- Protect:peak:ctr
  87
- Protect:peak:ctr
  88
- Protect:rms:time:max
  88
- Protect:rms:time:min
  88
- Protect:peak:time:max
  89
- Protect:peak:time:min
  89
Chapter11 List Operation Commands

90
- List:repeat
  90
- List:endstate
  90
- List:jumpto
  90
- List:run:record
  91
- List:run:repeat
  91
- List:recorder
  91
- List:configure
  92
- List:name
  93
- List:recall
  93
- List:record:num
  93
- List:save
  94
- List:recall:name
  94
- List:recall:num
  94
- List:run
  95
- List:stop
  95
- List:run:state
  95
Chapter12 Common Commands

96
- Cls
  96
- Ese
  96
- Ese
  97
- Esr
  97
- Idn
  98
- Opc
  98
- Rst
  99
- Sre
  99
- Sre
  100
- Stb
  100
- Trg
  101
- Tst
  101
- Wai
  101

Advertisement

Advertisement

Related Products

ITech Categories

Power Supply

Power Supply Test Equipment Watch Measuring Instruments Racks & Stands

More ITech Manuals