Heise PTE-1 Manuals

Manuals and User Guides for Heise PTE-1. We have 1 Heise PTE-1 manual available for free PDF download: Operating Manual

Heise PTE-1 Operating Manual (80 pages)

HAND HELD CALIBRATOR

Brand: Heise | Category: Test Equipment | Size: 1 MB

Table of Contents
3
Introduction
6
Base Unit Overview
6
Quick Select Module Overview
6
The GQS-1 Quick Select Pressure Module
7
The GQS-2 Quick Select Pressure Module
7
The GQS-RT1 Quick Select RTD Temperature Interface Module
7
The GQS-TC1 Quick Select Thermocouple Interface Module
8
Unpacking
8
Unpacking Product Upon Receipt Unpacking Product Upon Receipt
8
Product Storage
8
Product Cleaning
8
System Start-Up General Instructions
8
Battery Installation
8
Installation of Quick Select Modules
9
Starting up HHC System
9
Optional System Start up Procedures
10
Auto Off- Battery Save Function
10
Set up for Battery Charge Level Indication
11
Low Battery Icon
12
Programming Date and Time Information
12
Input of Owner/Operator Information
13
Removing Quick Select Modules
14
Key Function Overview
14
Port Select Function
15
Zero Function
16
Zeroing One of Two Installed Quick Select Pressure Module
16
Displaying Current & Voltage Measurements
16
Engineering Unit Selection
17
Selecting a Factory Programmed Engineering Unit Selecting a Factory Programmed Engineering Unit
17
Setting up a Custom (User Defined) Engineering Unit
17
Using a Custom (User Defined) Engineering Unit
18
Display of Two Different Engineering Units, for Two Installed Modules
19
Temperature Selection for H2O Conversion Factor
20
Tare Function
21
Hold Function
21
Using the Hold Function
21
Minimum and Maximum Value Tracking
22
Damping Function
22
Set up of Damping Function
22
Activating or Discontinuing Damping
23
Percent Function
23
Set up of Percent Function
23
Use of Percent Function
24
Flow Velocity and Flow Volume Measurement Background
25
Set up for Flow Velocity & Volume Measurement
25
Flow Velocity Measurement
25
Engineering Unit Selection for Flow Velocity
26
Flow Volume Measurement Flow Volume Measurement
26
Engineering Unit Selection for Flow Volume
27
Simultaneous Display of Two Flow Measurements in Independent Engineering Units
27
Simultaneous Display of Flow (Velocity or Volume) with a Pressure Measurement
28
Simultaneous Display of Flow (Velocity or Volume) with a Temperature Measurement
29
Simultaneous Display of Flow Volume and Flow Velocity
29
Simultaneous Display of Flow (Velocity or Volume) and
30
Leak Detection Function
31
Leak Rate Function Setup
31
Pressure Decay Function Set up
32
Sensor Selection for Performing Leak Rate or Pressure Decay Tests
32
Performing Leak Rate or Pressure Decay Tests
32
Temperature Measurement Using RTD Probes
33
Setting up the Calibrator for Temperature Measurement with an RTD Probe
33
Calibrating and Programming of the RTD Interface and Probe
35
Temperature Measurement with Thermocouple Detector
35
Setting up Calibrator for Use with Thermocouple Detector
36
Pressure and Temperature Switch Testing
37
Setting up for Pressure and Temperature Switch Testing
37
Trip Point Testing
37
Deadband Testing
38
RS232 Interface
39
Configuring RS232 Interface for Use with Dumb Terminal
39
RS232 Configuration Options
39
RS232 - ISO1745 Mode Functional Overview
39
RS232 - Journal Mode Functional Overview
39
RS232 - Inquiry Mode Functional Overview
40
RS232 Set up for Journal Mode Operation
40
RS232 Set up for Inquiry Mode Operation
41
Status
43
Reviewing Instrument Status
43
Battery Check Function
43
Dual Module Functions
44
Accuracy of Dual Module Measurements
44
Setting up Dual Module Differential Pressure Measurement
44
Setting up a Dual Module Summation Pressure Measurement
46
Data Logging Function (Optional)
47
Sequential Data Logging Function (Optional)
47
Setting up the Data Logging Function (Optional)
47
Labeling Function - Standard Data Logging Mode
48
Automatic Data Logging - Standard Data Logging Mode
48
Manual Data Logging - Standard Data Logging Mode
49
Review of Stored Data - on Instrument Display
50
Standard Data Logging Mode
50
Erasing of Selected Stored Data - Standard Data Logging Mode
51
Erasing All Stored Data - Standard Data Logging Mode
51
Certification Generation Enhanced Data Logging Mode
52
Set up and Use of Certification Generation Data Logging Mode
52
HHC System Set up for Uploading Stored Data into an IBM Compatible PC
57
Installing and Operating Upload Software
58
Battery Back up Replacement Battery Back up Replacement
58
Event Timer Function
58
Event Timer Set up
59
Data Logging Set up for Operation with the Event Timer
59
Alarm Function - Overview (Optional Feature)
60
Alarm Set up
61
Recertification of the Calibrator
62
Calibration/Recertification Overview
62
Required Equipment
62
As Received Readings of the Base Unit Electronics
62
Adjustment/Calibration Base Unit Electronics
64
Recertification of Quick Select Pressure Modules
66
Appendix A - Pressure Conversion Factors
70
Appendix B - ASCII Character Set
71
Appendix C - Product Specifications
74
Table II
76
Appendix D - RTD Probe Connector
77
Appendix E - Certification of the TC1 Thermocouple Interface Module
78

Heise Categories

Automobile Accessories Test Equipment Work Light Transducer Measuring Instruments

More Heise Manuals

Heise PTE-1 Manuals

Heise PTE-1 Operating Manual (80 pages)

Table of Contents

Related Products

Heise Categories