Sign In
Upload
Manuals
Brands
HACKER Manuals
Toy
ZOOM 4D
HACKER ZOOM 4D RC Airplane Manuals
Manuals and User Guides for HACKER ZOOM 4D RC Airplane. We have
2
HACKER ZOOM 4D RC Airplane manuals available for free PDF download: Technical Data Manual, Construction Manual
HACKER ZOOM 4D Construction Manual (9 pages)
Brand:
HACKER
| Category:
Toy
| Size: 10 MB
Table of Contents
Contents
1
Construction Guide
2
Final Check
2
Radio Control Set Installation
2
Centre of Gravity
2
Flying
2
RC Set- 4 Channel and Power Set
3
Insert the Complete Landing Gear into the Landing Gear Mount
3
Insert the Prop Shaft, the Propeller and the Spinner to the Electromotor
3
Insert the "Z" Wires into the Ailerons Control Horns in the Upper Wing
3
Insert the "Z" Wires into the Pushrod Connectors in the Lower Wing
3
Set the Ailerons to Neutral as Shown. Tighten the Screws in the Pushrod Connectors
3
Moving the Accu Pack Make the Model Balance. into the Fuselage Cut Opening for Accu Pack
3
The Accu Pack Press into the Hole in Fuselage
3
Part List
4
Complete the Landing Gear as Shown
4
Glue the Wheel Pants into the Landing Gear as Shown. Use CA Glue and Apply Activator Spray
4
Check the Alignment of Lower Wing and Upper Wing
4
Cut the Slot in the Landing Gear Covers Using Sharp Knife
4
Insert Landing Gear Covers on the Landing Gear and Cut the Edges Using Sharp Knife as Shown
4
Glue the Landing Gear Covers on the Landing Gear Using CA Glue as Shown
4
Right Position of the Slot for the Wire
5
Cut the Slot in the Side of the Fuselage Using Sharp Knife. the Slot Must be 3 MM Deep
5
Press the Wire into Slot
5
Glue the Engine Mount as Shown. Use CA Glue
5
Screw Engine into the Engine Mount Using Screws
5
Cut the Slot in the of the Wing Using Sharp Knife. the Slot Must be 3 MM Deep
5
Press Wire into Slot in the Wing
5
On the Flat Board Glue the Wire into Upper Side of the Upper Wing Using CA Glue and Activator Spray
5
Insert the Uper Wing on the Baldachin and the Wing Struts as Shown
5
Align the Uper Wing as Shown
5
Insert the Wing into the Fuselage as Shown. Glue the Wing in Place Using CA Glue
6
Into the Fuselage Drill 8Mm Hole for Aileron Servo Cable up to the Space for Receiver
6
Glue the Control Horns into the Ailerons with CA Glue as Shown
6
Insert the Wing Strut into the Lower Wing as Shown
6
Glue 2 Canopy Pins into the Canopy Use CA Glue
6
Pin the Holes into the Fuselage for the Antene. Insert the Antene into the Holes as Shown
6
Insert the Servos into the Hole as Showns. Us the Fusion Glue
6
Install the Pushrod Connector to the Servo Arm. Insert the Quicklock Onto the Pushrod Connector
6
Press the Tube into the Slot in Fuselage as Shown. Glue It Using CA Glue
6
Trim the Canopy According the Guidelines. Drill Three Holes 3Mm and Cut out in the Front as Shown
6
Cut a Slots in the Ailerons for the Control Horns as Shown
7
Using the Sharp Knife Cut the Slots for Control Horn (Elevator)
7
The Z Wire 0,8X330 Insert into the Pushrod Connector on the Horn of Servo for Elevator
7
In the Samme Manner Install the Tube into the Left Side of Fuselage
7
Press the Horn into the Slot in the Elevator Using CA Glue
7
Glue the Wing in Place Using CA Glue. Apply Glue at the Top and than to the Bottom
7
Glue the Control Horns into the Ailerons with CA Glue as Shown
7
Cut the Pushrod as Shown
8
Glue Vertical Fin on the Fuselage Using CA Glue. Check the Perpendicularity and Alignment as Shown
8
Onto Z Wire 0,8X330 Insert the Horn, Put the Wire through the Tube in the Fuselage
8
The Z Wire 0,8X330 Insert into the Pushrod Connector on the Horn of Servo for Rudder
8
Using the Sharp Knife Cut the Slots for Control Horn (Rudder)
8
Switch on the RC Set. Control Surfaces as Shown. the Connector Screws
8
Bend the Wire (al 1,6X120) as Shown
8
Stab the Wire into the Fuselage as Shown. Glue Using CA Glue
8
On the Flat Board Glue the Lower Wing Panels, Together Using CA Glue
8
Put the Rule on the Lower Wing as Shown
8
Advertisement
Hacker ZOOM 4D Technical Data Manual (12 pages)
TOP Flyer Almost Unbreakable Superaerobatic plane for 4D aerobatic flying Almost Ready to Fly
Brand:
Hacker
| Category:
Toy
| Size: 2 MB
Table of Contents
Construction Guide
2
Items Needed to Complete
2
Maximum Movements of the Control Surfaces
2
RC Set-4 Channel and Power Set
3
Part List
4
Spare Parts
4
Radio Control Set Installation
12
Flying
12
Advertisement
Related Products
Hacker RC-FLAIR 4.5
Hacker UAV Control 40 Opto Pro
Hacker 2303
Hacker Acrostar mk2 XL
Hacker ACTION SUPER ZOOM HC 1790B
Hacker ACTION SUPER ZOOM HC 1790C
Hacker ACTION SUPER ZOOM HC 1790D
HACKER Categories
Toy
Engine
Controller
Aircrafts
Paramotors
More HACKER Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL