Group Four Transducers GLDM 64.1 Manuals

Manuals and User Guides for Group Four Transducers GLDM 64.1. We have 1 Group Four Transducers GLDM 64.1 manual available for free PDF download: Technical Manual

Group Four Transducers GLDM 64.1 Technical Manual (50 pages)

Brand: Group Four Transducers | Category: Control Unit | Size: 1 MB

Table of Contents
2
Safety Instructions
5
Introduction and Specifications
6
Hardware and Wiring
7
Housing & Terminals
7
Terminals Load Cell Connection
7
Load Cell Connection
7
Terminals Power Supply
8
Canbus Interface
8
Seal Switch
9
Logic Inputs & Outputs
9
Communication and Getting Started
10
Serial Interface
10
Command Language
10
Baud Rate
10
Getting Started
10
Commands - Overview
11
Commands Description
13
System Diagnosis Commands - ID, IV, IS, SR, RS
13
ID Get Device Identity
13
Get Firmware Version
13
IS Get Device Status
13
SR Software Reset
14
RS Read Serial Number
14
Calibration Commands - CE, CM N, CI, MR, DS, DP, CZ, CG, ZT, FD, IZ, ZR, ZI, TM, TN, ZN, AZ, AG, CS
14
CE Read TAC* Counter / Open Calibration Sequence
14
CM N Set Maximum Output Value
14
CI Set Minimum Output Value
15
MR Set Multi-Range / Multi-Interval
15
DS Set Display Step Size
15
DP Set Decimal Point Position
15
Set Calibration Zero Point
16
CG Set Calibration Gain (Span)
16
ZT Enable / Disable Zero Tracking
16
FD Reset to Factory Default Settings
16
IZ Correction of System Zero
17
ZR Zero Range
17
ZI Initial Zero Range
17
TM Tare Mode
17
TN Set / Clear Non-Volatile Tare
18
ZN Set / Clear Non-Volatile Zero
18
AZ Absolute Zero Point Calibration (Ecal)
18
AG Absolute Gain Calibration (Ecal)
18
CS Save the Calibration Data
18
FT Firmware Type
19
Motion Detection Commands - NR, NT
19
NR Set No-Motion Range
19
NT Set No-Motion Time
19
Filter Setting Commands - FM, FL, UR
20
FM Filter Mode
20
FL Filter Setting
20
UR Update Rate and Averaging
21
Taring and Zeroing Commands - SZ, ZA, RZ, ST, RT, SP
21
SZ Set System Zero
21
RZ Reset Zero
22
ST Set Tare
22
RT Reset Tare
22
SP Set Preset Tare
22
Output Commands - GG, GN, GT, GS, GW, GA, GL, of
23
GG Get Gross Value
23
GN Get Net Value
23
GT Get Tare Value
23
GS Get ADC Sample Value
23
GW Get Data String "Net, Gross and Status
23
GA Get Triggered Average Value
23
GL Get Data String "Average, Gross and Status
24
OF Output Format for Data String GW and GL
24
Auto-Transmit Commands - SG, SN, SX, SA, SL
25
SG Send Gross Value Continuously
25
SN Send Net Value Continuously
25
SX Send ADC Sample Value Continuously
25
SA Send Triggered Average Value Automatically
25
Send Data String "Average, Gross and Status" Automatically
25
SW Send Data String "Net, Gross and Status" Continuously
25
Commands for External I/O Control - IN, IO and OM
26
IN Read Status of the Logic Inputs
26
IO Read / Modify the Status of the Logic Outputs
26
OM Control of the Logic Outputs by the Host Application
26
Setpoint Output Commands - S'n', H'n', A'n', HT
28
S'n' Setpoint Value
28
H'n' Hysteresis and Switching Action for a Setpoint
28
A'n' Allocation Source for a Setpoint
29
HT Hold Time for All Setpoints
29
Communication Setup Commands - AD, CR, NA, NS, BR, DX
30
AD Device Address - Serial Channel
30
NA Network Address - Canbus
30
NS Network Settings - for Serial Channel and CAN Interface
30
BR Baud Rate - Serial Channel
31
DX Full Duplex - Serial Channel
31
Save Calibration and Setup Data Commands - CS, WP, SS, GI, PI
32
CS Save the Calibration Data
32
WP Save the Setup Parameters
32
SS Save Setpoint Parameters
32
GI Get an Image File from the EEPROM
32
PI Download an Image File to the EEPROM
32
Trigger Commands - SD, MT, GA, TE, TR, TL, SA
33
SD Start Delay Time
33
MT Measuring Time
33
GA Get Triggered Average Value
33
TE Trigger Edge
33
TR Software Trigger
33
TL Trigger Level
34
SA Send Triggered Average Value Automatically
34
Example of Live Checkweigher Measurement with DOP4
35
Re-Trigger Commands - RW, TT, TS, DT, TW and TI
36
RW Trigger Window for Re-Trigger Function
36
TT Averaging Time for Re-Trigger Function
36
TS Stop Value for Re-Trigger Function
36
DT Short-Time Averaging Period
36
TW Window for Automatic Taring
37
TI Averaging Time for Automatic Taring
37
Example of Live Multihead Scale Measurement with DOP4
38
Canopen Interface
39
General
39
The Pdos
40
The Sdos
41
Communication Profile
41
Object Directory
41
Use in "Approved" Applications
50

Group Four Transducers Categories

Measuring Instruments Control Unit

More Group Four Transducers Manuals

Group Four Transducers GLDM 64.1 Manuals

Group Four Transducers GLDM 64.1 Technical Manual (50 pages)

Table of Contents

Related Products

Group Four Transducers Categories