Granite River Labs GRL-DP21-SINK-AN Manuals

Manuals and User Guides for Granite River Labs GRL-DP21-SINK-AN. We have 1 Granite River Labs GRL-DP21-SINK-AN manual available for free PDF download: User Manual

Granite River Labs GRL-DP21-SINK-AN User Manual (105 pages)

DisplayPort PHY 2.1 Receiver Calibration and Test User Guide & Method of Implementation Using Anritsu MP1900A BERT and High Performance Real-Time Oscilloscope with DisplayPort 2.1 Receiver Calibration and Test Automation Software

Brand: Granite River Labs | Category: Receiver | Size: 6 MB

Table of Contents
3
Introduction
9
Resource Requirements
10
Equipment Requirements
10
Software Requirements
12
Installing and Setting up Grl-Dp21-Sink-An Software
13
Download and Set U Pgrl-Dp21-Sink-An Software
13
On the Anritsu MP1900A BERT
13
On the PC Used for GRL Framework Installation
14
Figure 1. Turn on Miscellaneous System
14
Figure 2. Select and Launch GRL Framework
14
Figure 3. Start Displayport Sink Test 2.1 Application
15
Figure 4. See License Details
15
Figure 5. Check License for Installed Application
15
Figure 6. Connect Instruments with GRL Software
16
Configure the Grl-Dp21-Sink-An Software before Calibration and Testing
17
Enter Calibration/Test Session Information
17
Set up Conditions for Calibration/Testing
17
Figure 7. Session Info Page
17
Figure 8. Select Lane under Tests
18
Figure 9. Select Test Points
18
Figure 10. Select Data Rates
18
Set up aux Controller for DUT Test Automation
19
Select Calibration/Test
19
Figure 11. Select SJ Frequencies
19
Figure 12. Select aux Controller
19
Figure 13. Calibration Selection
20
Figure 14. Tests Selection
20
Configure Calibration/Test Parameters
21
Figure 15. Parameters Configuration Page
21
Configure Calibration Target Values
23
Run Calibration/Tests
24
Figure 16. Calibration Overwrite
24
Figure 17. Run Tests Page
24
Sink Calibration Connection Setups
26
Pre-Calibration/Test Procedures
26
Connection Setup for Anritsu Mp1900A Bert Generator Set
26
Figure 18. Connection Setup for MP1900A BERT Generator Set Modules
26
Displayport USB Type-C Fixture Connector Pin Assignments
27
Figure 19. Displayport USB Type-C Receptacle Fixture Connector Pin Assignments
27
Figure 20. Displayport USB Type-C Plug Fixture Connector Pin Assignments
27
Standard/Mini Displayport Fixture Connector Pin Assignments
28
Figure 21. Standard/Mini Displayport Receptacle Fixture Connector Pin Assignments
28
Figure 22. Standard/Mini Displayport Plug Fixture Connector Pin Assignments
28
Calibration Connection Setups
29
Calibration Setup at TP1
29
Figure 23. Typical TP1 Sink Calibration Setup
29
Calibration Setup at TP3_EQ for Displayport USB Type-C Mode
30
Figure 24. Setup for TP3_EQ Calibration at 10G for Displayport USB Type-C Mode
30
Figure 25. Setup for TP3_EQ Calibration at 13.5G for Displayport USB Type-C Mode
31
Figure 26. Setup for TP3_EQ Calibration at 20G for Displayport USB Type-C Mode
32
Calibration Setup at TP3_EQ for Standard/Mini Displayport Mode
33
Figure 27. Setup for TP3_EQ Calibration at 10G for Standard/Mini Displayport Mode
33
Figure 28. Setup for TP3_EQ Calibration at 13.5G for Standard/Mini Displayport Mode
34
Figure 29. Setup for TP3_EQ Calibration at 20G for Standard/Mini Displayport Mode
35
Sink Dut Compliance Test Setups
36
Test Connection Setups
36
DUT BER Compliance Test Setup at TP1 for Displayport USB Type-C Mode
36
Figure 30. BER Compliance Test Setup for DP Sink DUT at TP1 for Displayport USB Type-C Mode
36
DUT BER Compliance Test Setup at TP1 for Standard/Mini Displayport Mode
38
Figure 31. BER Compliance Test Setup for DP Sink DUT at TP1 for Standard/Mini Displayport Mode
38
DUT BER Compliance Test Setup at TP3_EQ for Displayport USB Type-C Mode
40
Figure 32. Displayport USB Type-C Mode BER Compliance Test Setup for DP Sink DUT at TP3_EQ at
40
Figure 33. Displayport USB Type-C Mode BER Compliance Test Setup for DP Sink DUT at TP3_EQ at
42
Figure 34. Standard/Mini Displayport Mode BER Compliance Test Setup for DP Sink DUT at TP3_EQ at 10G
43
Margin Testing
45
Figure 35. Standard/Mini Displayport Mode BER Compliance Test Setup for DP Sink DUT at TP3_EQ at 13.5G and 20G
45
Figure 36. Margin Test Configuration
46
Figure 37. Sink Margin Test Selection
46
Figure 38. Report Results Page
47
DUT Information
48
Results Summary Table
48
Figure 39. DUT Information
48
Figure 40. Results Summary Table Example
49
Calibration & Test Result Details
50
Esults
51
Figure 41. Calibration/Test Result Details Example
51
Figure 42. Delete Individual Calibration/Test Results Example
51
Figure 43. Saving and Loading Calibration and Test Sessions
52
Tp1
53
Figure 44. Jitter Clock Source Setting
54
Figure 45. PPG Misc2 Settings
55
Figure 46. Pattern Setting
56
Figure 47. PPG Emphasis Setting
57
Figure 48. SSC Setup
57
Figure 49. DATA+ Amplitude Setting
57
Figure 50. CM Setting
58
Set up Oscilloscope
59
Figure 51. Oscilloscope Vertical and Horizontal Setup
59
Figure 52. Oscilloscope Clock Recovery Setup
60
Figure 53. Oscilloscope Jitter Setup
62
Record ISI Measurements
63
Figure 54. ISI Measurement Preset Table
63
Figure 55. 4Tap Emphasis CH1 Interface
64
Figure 56. Optimized Preset (Minimum Ddjpp) Measurement on Keysight Scope
65
Figure 57. Optimized Preset (Minimum Ddjpp) Measurement on Tektronix Scope
65
Figure 58. Calibration to Phase Match on Keysight Scope
66
Figure 59. Calibration to Phase Match on Tektronix Scope
66
Figure 60. Calibrate ACCM
67
Figure 61. Calibrate ACCM Peak-To-Peak Amplitude
68
Figure 62. Jitter Amplitudes
69
Figure 63. Calibrate RJ Amplitude #1
70
Figure 64. Calibrate RJ Amplitude #2 on Keysight Scope
71
Figure 65. Calibrate RJ Amplitude #2 on Tektronix Scope
71
Figure 66. Calibrate SJ Amplitude #1
72
Figure 67. Calibrate SJ Amplitude #2 on Keysight Scope
73
Figure 68. Calibrate SJ Amplitude #2 on Tektronix Scope
73
Figure 69. TJ Measurement on Keysight Scope
74
Figure 70. TJ Measurement on Tektronix Scope
75
Figure 71. Eye Amplitude
76
Figure 72. Eye Mask on Keysight Scope
77
Figure 73. Eye Mask on Tektronix Scope
77
Figure 74. DC Gain Setting
79
Figure 75. DFE Setting
80
Figure 76. Eye Amplitude
81
Set up Oscilloscope
83
Tp1
83
Record ISI Measurements
85
Bit / S ) Receiver at Tp3_Eq
87
Figure 77. DFE Setting
89
Figure 78. Eye Amplitude
90
Figure 79. Eye Amplitude Measurements
91
Set up Oscilloscope
92
S ) Receiver at Tp1
92
Record ISI Measurements
94
S ) Receiver at Tp3_Eq
96
Figure 80. DC Gain Setting
97
Figure 81. DFE Setting
98
Figure 82. Eye Amplitude
99
Figure 83. Eye Amplitude Measurements
100
Figure 84. Keysight Connection Expert
102
Figure 85. Oscilloscope's VISA Address
103
Figure 86. Openchoice Instrument Manager in Start Menu
104
Figure 87. Openchoice Instrument Manager Menu
105

Granite River Labs Categories

Receiver Measuring Instruments Test Equipment Laboratory Equipment

More Granite River Labs Manuals

Granite River Labs GRL-DP21-SINK-AN Manuals

Granite River Labs GRL-DP21-SINK-AN User Manual (105 pages)

Table of Contents

Related Products

Granite River Labs Categories