Dahen DA300P Inverter Power Source Manuals

Dahen DA300P Inverter Power Source Manuals

Manuals and User Guides for Dahen DA300P Inverter Power Source. We have 1 Dahen DA300P Inverter Power Source manual available for free PDF download: Owner's Manual

Dahen DA300P Owner's Manual

Dahen DA300P Owner's Manual (86 pages)

Brand: Dahen | Category: Inverter | Size: 1.97 MB

Table of Contents

Table of Contents
2
Arc Welding Safety Precautions
3
Safety Information
3
- Methods of Reducing EMC
  7
- Principal Safety Standards
  8
General Notice of Operation
9
- Operation Cycle of 40% Duty Cycle
  9
- Rated Duty Cycle
  9
- Welding Current (A)
  9
- Other Equipment
  10
Standard Composition and Accessories
10
- STICK Welding
  10
- TIG Welding
  10
Function of Equipment
11
Necessary Power Source Equipment
13
- Precautions for Use of the Engine Generator
  13
- Welding Power Source Equipment
  13
Transport and Installation
14
Connecting of the Welding Power Source
16
Connection Procedure and Ground for Safety Use
16
Welding Preparation
22
Operation
28
- DC TIG Welding
  29
- Parameter Setting
  29
- Initial Current
  30
- Pre Flow Time
  30
- Pulse Current
  30
- Upslope Time
  30
- Crater Current
  31
- Down Slope Time
  31
- Pulse Frequency
  31
- Setting Current Range
  31
- AC TIG Welding
  32
- AC-DC TIG Welding
  32
- Notice of Using AC TIG Mode
  32
- Winding Method of Excess Cable
  33
- AC Frequency
  34
- AC Waveform
  34
- AC Balance Setup
  35
- AC-DC Change-Over Frequency Setup
  36
- Automatic Insertion
  36
- Manual Insertion
  36
- Pulse Setting
  37
- Crater Setting
  38
- Slope Setting
  38
- Welding with Various Functions Combined
  39
- ARC SPOT Setting
  40
- High Frequency Start
  41
- Lift Start
  41
- START Setting
  41
- Cooling Torch Selection
  42
- Gas Check
  42
- How to Use Internal Functions
  43
- Internal Functions
  43
- Changing Sequence in Arc Spot Mode
  44
- Changing Sequence in Crater on (REPEAT) Mode
  44
- Selecting Start Current Level
  44
- Available Plug
  45
- Selecting AUTO or MANUAL Mode
  45
- External Voltage (0-10V) Control
  46
- External Voltage (0-12V) Control
  46
- Pulse Peak Ratio Adjustment
  46
- AC Ratio Adjustment
  47
- External Output Terminal 1 Switching
  47
- Operating Sound Switching
  47
- Result Display Holding Time Setup
  47
- Current Adjustment by Torch Switch
  48
- Soft Pulse
  48
- Current Adjustment Function with Torch Switch at Pulse Function
  49
- Current Offset Adjustment
  49
- Indication of Welding Voltage
  49
- Memory Condition Interlocking Function
  49
- 2 Stroke Slope Function
  50
- Analog Remote Control
  50
- Analog Remote Control (K5416T)
  51
- DC STICK Welding
  51
- Internal Function Setting
  51
- Welding Current Setting
  51
- Indication on Digital Display
  52
- Information Common to All Models
  52
- Output Current at Welding
  52
- Parameter Set Values
  52
- Adjustor Knob
  53
- JOB MEMORY Function
  53
- Key Lock
  53
- Holding the Welding Conditions in Memory
  54
- SAVE Function
  54
- LOAD Function
  55
- Reading out the Preset Welding Conditions
  55
- Memory Mode Operation
  56
- Readout Mode Operation
  56
- Erasing the Welding Conditions
  57
- Automatic Stop of Fan
  58
- Confirming Software Version
  58
- Fan Noise Reducing Function
  58
- Resetting to Initial Values
  58
Applied Function
59
- How to Solve an Error
  59
- Daihen Display
  60
- E-000 Display
  60
- E-100 Display
  60
- E-200 Display
  60
- E-510 Display
  61
- E-600 Display
  61
- E-710 Display
  61
- E-751 Display
  61
- 12P Terminal Block
  62
- External Connection of Inside Terminal Block of Automatic Machine
  62
- 12P Terminal Block (TM 12P)
  63
- Precaution for Connection with Terminals on the Terminal Block
  63
- Air-Cooled Torch
  64
- Connecting to the Extension Torch Cable/Hose
  64
- Optional Accessories
  64
- Water-Cooled Torch
  64
- Extension Cable/Hose
  65
- Cable Hose
  66
- Optional Parts
  66
- Tig Boy
  66
- TIG BOY Special Torch
  66
- Cerium-Tungsten Electrode
  67
- Thoriated Tungsten Electrode
  67
- TIG Filler Wire Feeding System
  67
- Tungsten Electrode
  67
Maintenance and Troubleshooting
68
- Carrying out Maintenance on the Welding Power Source
  69
- Check the Following Daily
  69
- Check the Following each Three to Six Months
  69
- Precaution for Replacement of the Printed Circuit Board
  69
- Insulation Resistance Test
  70
- Replacement of Batteries
  70
- Troubleshooting
  71
- Schematic Diagram
  74
- Back Side of Front Panel
  75
- Bottom Chassis
  75
- Parts Layout
  75
- Under Frame
  75
Parts List
76
Specifications
78
- Specifications
  79
- External View
  80
- Function
  82
- Initial Values and Setting Range of Parameters
  82
- Before Using the Welding Power Source
  83
- Loading the Welding Conditions
  83
- Presetting the Welding Conditions
  83
- Quick Manual
  83
Service and Support
84

Advertisement

Advertisement

Related Products

Dahen Categories

More Dahen Manuals