User Manuals: Case IH DCX101 Farm Equipment

Manuals and User Guides for Case IH DCX101 Farm Equipment. We have 1 Case IH DCX101 Farm Equipment manual available for free PDF download: Repair Manual

Case IH DCX101 Repair Manual

Case IH DCX101 Repair Manual (260 pages)

Disc Mower-Conditioner

Brand: Case IH | Category: Farm Equipment | Size: 7 MB

Table of Contents

Table of Contents
3
Description Page
4
Foreword
14
Precautionary Statements
15
Safety
16
Manual Holder
18
Product Identification Number
18
Hardware Torque Values
19
Installation of Adjustable Fittings in Straight Thread O-Ring Bosses
22
Standard Torque Data for Hydraulic Tubes and Fittings
22
Installation of ORFS (O-Ring Flat Faced) Fittings
23
Pipe Thread Fitting Torque
23
Ecology and the Environment
24
Universal Symbols
25
Tractor Requirements
26
Tractor Drawbar Dimensions
27
Attaching the Mower-Conditioner to the Tractor
28
Hydraulic Hoses
28
Jack Assembly
28
Connecting Hydraulic Hoses to the Tractor
29
Hydraulic Cylinders
29
Bleeding Air from the Lift Cylinders
30
Safety Chain
31
Slow-Moving Vehicle Emblem
31
Transporting on Highways
31
Transporting the Mower-Conditioner
31
Trailing Lights
32
Towing with a Tractor
33
Towing with a Truck
34
Parking the Machine
35
Storing the Mower-Conditioner
35
Specifications
36
Special Tools
37
Conditioning (Roll Pressure)
40
Unplugging the Conditioner Rolls
40
Roll Timing
41
Rubber Rolls
42
Steel Rolls
42
Roll Gap
43
Rubber Rolls
43
Conditioner Belt
44
Steel Rolls
44
Cutter Bar Flotation
45
Cutting Height
46
Chapter 3 - - Lubrication

49
- Description Page
  49
- Section 00 - - General Information
  49
- Lubrication
  50
- Recommended Lubricants
  50
- Gearboxes
  51
- Grease Fittings
  51
- Lubrication Schedule
  51
- PTO Slide Collar
  52
- Weasler Primary PTO
  52
- Bondioli Primary PTO
  53
- Every 50 Hours
  53
- Front CV Joint
  54
- Secondary PTO
  54
- Rear CV Joint and Slip Clutch Assembly
  55
- Telescoping Section
  55
- Cutter Bar Driveshaft
  56
- Roll Drive
  56
- Upper Roll Pivot Arms
  56
- Wheel Arms and Header Lift Arms
  56
- Cutter Bar Mounting Bolts
  57
- Tongue Pivot Pin
  57
- Wheel Bearings
  57
- After First 50 Hours
  58
- Step-Up Gearbox
  58
- Bevel Gearbox
  59
- Every 100 Hours
  59
- Roll Pressure Crank
  59
- Cutter Bar Modules
  61
- Every 200 Hours
  61
- Roll Drive Gearbox
  61
- Every 400 Hours
  62
- Wheel Bearings
  62
- Description Page
  67
- Description of Operation
  68
- 540 RPM PTO Units
  70
- Drive Shaft Removal/Installation
  70
- Primary PTO
  70
- 1000 RPM PTO Units
  71
- Secondary PTO Assembly
  72
- 540 RPM Ptos
  73
- CV Drivelines Guards -- Disassembly
  73
- Standard Drivelines Guards -- Disassembly
  73
- Driveline Guards -- Inspection
  74
- Standard Driveline Guards -- Assembly
  75
- Front Guard Assembly
  76
- 1000 RPM Ptos
  77
- 1000 RPM Assembly
  78
- Secondary PTO Disassembly
  81
- Secondary PTO Assembly
  84
- U-Joints -- Disassembly
  86
- U-Joints -- Inspection
  87
- U-Joints -- Assembly
  88
- Repair Time Schedule
  89
- Description
  91
- Slip Clutch
  92
- Slip Clutch - Disassembly
  93
- Slip Clutch - Removal
  93
- Slip Clutch - Inspection
  94
- Slip Clutch - Run in
  97
- Chapter 3 - - Overrunning Clutch
  99
- Description
  99
- Section 31 - - Implement Power Take-Off (Pto)
  99
- Overrunning Clutch
  100
- Overrunning Clutch - Disassembly
  100
- Overrunning Clutch - Inspection
  101
- Overrunning Clutch - Assembly
  102
- Disassembly
  105
- Slip with Overrunning Clutch
  105
- Assembly
  109
- Description
  115
- Step-Up Gearbox
  115
- Step-Up Gearbox - Disassembly
  119
- Step-Up Gearbox - Assembly
  122
- Description
  127
- Hydraulic Diagram
  129
- Bleeding Air from the Lift Cylinders
  131
- Lift Cylinder Removal
  132
- Disassembly
  133
- Inspection
  133
- Master Cylinder
  133
- Assembly
  134
- Disassembly
  135
- Inspection
  135
- Slave Cylinder
  135
- Assembly
  136
- Disassembly
  137
- Header Tilt Cylinder
  137
- Removal
  137
- Assembly
  138
- Inspection
  138
- Disassembly
  139
- Swing Cylinder
  139
- Assembly
  140
- Inspection
  140
- Adjustment
  144
- Removal
  145
- Installation
  146
- Disassembly: Flotation Spring Wrench
  147
- Disassembly
  148
- Assembly
  149
- Installing the Wire Harness
  152
- Trailing Lights
  152
- Description Page
  157
- Introduction
  158
- Discs
  161
- Knife and Bolt Inspection
  162
- Knife Replacement
  163
- Crop Lifter Replacement
  165
- Rock Guard Replacement
  165
- Skid Shoe Replacement
  165
- Cutter Bar Inspection/Failure Analysis
  166
- Top Cap Removal
  169
- Inspection
  170
- Top Cap Installation
  171
- Cutter Bar Removal
  173
- Cutter Bar Installation
  176
- Cutter Bar Disassembly
  178
- Cutter Bar Reassembly
  179
- Disc Module - Disassembly
  182
- Disc Module - Assembly
  184
- Bevel Gearbox - Removal
  192
- Bevel Gearbox - Disassembly
  195
- Bevel Gearbox - Reassembly
  198
- Bevel Gearbox - Installation
  203
- Introduction
  208
- Conditioner Belt
  209
- Conditioner Belt Replacement
  210
- Conditioner Roll Gearbox - Removal
  211
- Conditioner Roll Gearbox - Disassembly
  213
- Conditioner Roll Gearbox - Assembly
  214
- Conditioner Roll Gearbox - Installation
  215
- Upper Conditioner Roll Drive Shaft - Disassembly
  217
- U-Joints - Assembly
  219
- Lower Conditioner Roll - Removal
  220
- Lower Conditioner Roll - Installation
  224
- Upper Conditioner Roll - Removal
  230
- Upper Conditioner Roll - Installation
  233
- Conditioner Roll Tension System
  235
- Left Side Torsion Arm and Bar Disassembly
  235
- Right Side Torsion Arm, Torsion Bar and Adjusting Tube Disassembly
  237
- Conditioner Roll Tension System - Assembly
  239
- Right Side Torsion Arm, Torsion Bar and Adjusting Tube Assembly
  239
- Left Side Torsion Arm and Bar Assembly
  241

Advertisement

Advertisement

Related Products

Case IH Categories

Tractor Farm Equipment Lawn and Garden Equipment Portable Generator Paint Sprayer

More Case IH Manuals