User Manuals: Cal Amp VIPER SC+ 100 series Router

Manuals and User Guides for Cal Amp VIPER SC+ 100 series Router. We have 1 Cal Amp VIPER SC+ 100 series Router manual available for free PDF download: User Manual

Cal Amp VIPER SC+ 100 series User Manual (206 pages)

INTELLIGENT IP ROUTERS FOR LICENSED SPECTRUM

Brand: Cal Amp | Category: Network Router | Size: 6 MB

Important Notice
3
Table of Contents
6
1 Viper SC + Overview

11
- General Description
  11
- Operational Characteristics
  11
- Physical Description
  12
  - Chassis Dimensions
    12
  - LED Panel
    12
  - Front Panel
    13
    
    Ethernet Lan Port
    14
    
    Power Connector
    15
    
    Antenna Connector
    15
- Part Numbers and Availability
  16
  - Viper SC+ Radio
    16
  - Fan Kits and Cables
    18
- Components
  19
  - Basic Unit
    19
  - Two- and Three-Piece Kit Additional Items
    20
2 Network Architecture and System Planning

21
- Network Architecture
  21
- IP Forwarding Modes
  24
  - Bridge Mode
    24
  - Router Mode
    26
  - Viper Router Generator (VRG) Program
    29
  - Multispeed Networking
    29
- Understanding RF Path Requirements
  30
- Site Selection and Site Survey
  31
  - Site Selection
    31
  - Site Survey
    31
- Selecting Antenna and Lightning Arrestor Combinations
  31
  - Lightning Arrestor Overview
    31
  - Antenna Overview
    32
  - The Wrong Combination
    32
  - Good Design Practices
    33
- Selecting Antenna and Feedline
  34
- Terrain and Signal Strength
  37
- Radio Interference
  37
3 Getting Started: Quick Setup and Initial Configuration

38
4 Viper SC+ Web Interface

46
- Home
  47
  - Unit Status
    47
  - RF Status
    49
  - Basic Settings
    50
- Radio Settings
  51
  - RF Settings
    51
  - Cwid
    54
  - RF Tests
    56
- RF Network Settings
  58
  - RF Network
    58
  - RF Bandwidth Management
    60
  - Additional Settings
    62
  - Neighbor Table
    64
  - Neighbor Discovery
    66
  - Global Settings
    70
  - Vlan
    71
  - Vlan Configuration
    72
  - Qos
    75
  - Vlan Membership
    75
  - Qos Statistics
    79
- LAN Settings
  80
  - Dhcp
    82
  - Sntp
    83
  - Time Zone
    84
  - Broadcast Multicast
    85
  - Vlan
    86
  - Ethernet (PHY)
    93
- Router
  93
  - Routing Table
    94
  - Nat
    96
  - Vts
    97
- Serial
  100
  - COM Port and Setup Port
    100
  - Vlan
    107
  - Advanced
    110
- Security
  111
  - Password
    111
  - AES Encryption
    112
  - Radius
    113
  - Client Configuration
    114
  - Vpn
    115
    
    Service Control
    117
    
    Status and Statistics
    118
- Diagnostics
  123
  - Interface Statistics
    123
  - Remote Statistics
    125
  - Snmp
    127
  - Online Diagnostics
    129
  - Radio Log
    133
- Device Maintenance
  134
  - Config Control
    134
  - Factory Settings
    135
  - Package Control
    136
  - Wing Commander
    136
  - General Settings
    138
5 Network Optimization

140
- Maximizing TCP/IP Throughput
  140
- Maximizing Throughput with a Weak RF Link
  140
  - Use Router Mode with RF Acknowledgements Enabled
    140
  - Reduce RF Network Bit Rate
    140
  - Use Data Retries
    141
  - Use Collision Avoidance
    141
6 Using Calamp-Provided and Cloned Viper Configurations

142
- Using Calamp Pre-Provided ("Canned") Configurations
  142
- Cloning a Viper
  143
7 Upgrading Firmware

144
- Firmware Introduction
  144
- How the Viper Firmware Is Upgraded
  144
  - Upgrade the Modem Firmware
    144
  - Upgrade the Radio Firmware
    145
APPENDIX A - Abbreviations and Definitions

146
APPENDIX B - Viper SC+™ Specifications

149
- General Specifications
  149
- Viper SC+™ Overall Dimensions and Mounting Hole Locations
  154
APPENDIX C - Viper SC+™ Regulatory Certifications

155
- DECLARATION of CONFORMITY for MODELS # 140-5018-60X, 140-5048-40X, and 140-5048-60X
  156
- EU and EFTA Member States' Acceptable Frequency Table
  157
APPENDIX D - UL Installation Instructions

163
APPENDIX E - Viper SC+™ Site Installation and Setup General Guidelines

164
APPENDIX F - Viper SC+™ Power-Save Mode

167
- Power Save Mode Faqs
  169
APPENDIX G - NAT Overview

170
- NAT on Viper
  171
  - Ethernet Interface Private
    171
  - RF Interface Private
    173
  - User NAT Entries
    176
  - NAT Port Forwarding
    177
APPENDIX H - MIB File Overview

179
APPENDIX I - VLAN Introduction

182
- VLAN Tagging and Untagging
  182
  - VLAN Tagging
    182
  - VLAN Untagging
    183
- Interface Modes
  183
  - Untagged Mode
    183
  - Tagged Mode
    184
- VLAN Member Table
  185
- Examples
  185
  - Bridge Mode (VLAN Disabled)
    186
  - Bridge Mode (VLAN Enabled)
    188
APPENDIX J - Viper PLC Setup

190
APPENDIX K - Service and Support and Warranty Statement

204
- Warranty Statement
  205

Cal Amp Categories

GPS

Network Router Modem Telephone Accessories Wireless Router

More Cal Amp Manuals

User Manuals: Cal Amp VIPER SC+ 100 series Router

Cal Amp VIPER SC+ 100 series User Manual (206 pages)

Table of Contents

1 Viper SC + Overview

2 Network Architecture and System Planning

3 Getting Started: Quick Setup and Initial Configuration

4 Viper SC+ Web Interface

5 Network Optimization

6 Using Calamp-Provided and Cloned Viper Configurations

7 Upgrading Firmware

APPENDIX A - Abbreviations and Definitions

APPENDIX B - Viper SC+™ Specifications

APPENDIX C - Viper SC+™ Regulatory Certifications

APPENDIX D - UL Installation Instructions

APPENDIX E - Viper SC+™ Site Installation and Setup General Guidelines

APPENDIX F - Viper SC+™ Power-Save Mode

APPENDIX G - NAT Overview

APPENDIX H - MIB File Overview

APPENDIX I - VLAN Introduction

APPENDIX J - Viper PLC Setup

APPENDIX K - Service and Support and Warranty Statement

Related Products

Cal Amp Categories