Bailey Infi 90 IMCPM02 Manuals

Manuals and User Guides for Bailey Infi 90 IMCPM02. We have 1 Bailey Infi 90 IMCPM02 manual available for free PDF download: Instructions Manual

Bailey Infi 90 IMCPM02 Instructions Manual

Bailey Infi 90 IMCPM02 Instructions Manual (55 pages)

Communication Port Module

Brand: Bailey | Category: Control Unit | Size: 1 MB

Table of Contents

Table of Contents
7
Section 1 - Introduction

10
- Overview
  10
- General Description
  10
  - Faceplate
    11
  - Circuit Board
    11
- IMCPM02 Module Application Example
  11
  - Hardware Application
    12
  - Intended User
    12
  - Instruction Content
    12
  - How to Use this Manual
    12
  - Reference Documents
    13
  - Nomenclature
    13
  - Glossary of Terms and Abbreviations
    14
  - Specifications
    15
- Glossary of Terms and Abbreviations (Continued)
  15
Section 2 - Description and Operation

16
- Introduction
  16
- Theory of Operation
  16
- Block Diagram of the IMCPM02 Module
  16
  - Serial Port
    17
  - Microprocessor
    17
  - Clock/Timer
    17
  - Memory
    17
  - Module Bus/Controlway
    18
  - Leds
    18
  - Dipswitches/Jumpers
    18
  - Ctt Interface
    19
Section 3 - Installation

20
- Introduction
  20
- Special Handling
  20
- General Handling
  21
- Dipswitches and Jumpers
  21
  - Dipswitch SW2 - Module Options and Diagnostics
    22
- Switch and Jumper Positions
  22
  - Switch SW3 - Module Address
    23
- Dipswitch SW2 Settings for Normal Mode
  23
  - Jumper Installation
    24
- Dipswitch SW3 Settings
  24
- Schematic Diagram of Jumpers J1 through J6
  25
  - Jumpers J1 through J3
    26
  - Jumper J4
    26
  - Jumper Arrays J5 and J6
    26
  - Jumpers J11 and J12
    26
- DCE Setting for Jumper Array J5 and J6
  27
- DTE Setting for Jumper Array J5 and J6
  27
- Loopback Setting for Jumper Array J5 and J6
  27
  - Preparing the Module Mounting Unit
    28
    
    Controlway Cable
    28
- Schematic Diagram of Jumpers J11 and J12
  28
  - Installing the Module
    29
- Controlway Cable Installation
  29
  - Installing the Termination Unit/Module
    30
Section 4 - Operation

31
- Introduction
  31
- Start-Up
  31
- Red/Green Status Led
  31
- Faceplate Leds 1 through 8
  31
- Reset Switch
  32
- On-Line Hardware Diagnostics
  32
Section 5 - Troubleshooting

33
- Introduction
  33
- Led Display
  33
- Led Error Codes
  33
- IMCPM02 Faceplate and LED Status Indicators
  33
- Diagnostic Tests
  33
- Red Status LED Error Codes
  34
  - Connectors
    35
    
    P1 - Power
    35
    
    P3 - Input/Output
    35
- Module Mounting Unit Signals
  35
- Termination Unit Signals
  35
  - P4 - CTT Port
    36
  - P5 - EWS Port
    36
  - P6 - Utility Port
    36
  - Diagnostics
    36
- CTT Port Signals
  36
- EWS Port Signals
  36
  - Dipswitch Selection
    37
- Switch Positions
  37
  - LED Display
    38
- Dipswitch SW2 Settings for Diagnostic Mode
  38
- Leds - Pass/Fail
  39
  - Tests
    40
    
    00 - Switches and Leds
    40
    
    01 - CPU Test
    40
    
    02 - ROM Test
    40
    
    04 - Static RAM Test
    40
    
    09 - Module Bus/Controlway Test
    40
    
    0A - Timer Interrupt Test
    40
    
    0B - Dispatcher Interrupt Test
    40
    
    0C - RS232 DUART Test
    41
    
    0E - CTT Module Bus Test
    41
    
    0F - Null Test
    41
    
    10 - Group Test
    41
    
    11 - RS232 DUART External Loopback Test
    41
Section 6 - Maintenance

42
- Introduction
  42
- Maintenance Schedule
  42
Section 7 - Repair/Replacement Procedures

43
- Introduction
  43
- Module Replacement
  43
- Recommended Spare Parts List
  43
Section 8 - Support Services

44
- Introduction
  44
- Replacement Parts and Ordering Information
  44
- Training
  44
- Technical Documentation
  44
Appendix A - Enhanced Module Status

45
- Enhanced Module Status Block
  45
- Enhanced Module Status
  46
Appendix B - Nimp01 Termination Module Configuration

47
Appendix C - Ntmp01 Termination Unit Configuration

50
- Introduction
  50
  - NTMP01 Dipshunt Configuration for Modem (DCE) Connection
    50
  - NTMP01 Dipshunt Configuration for EWS (DTE) Connection
    50
- C-3. NTMP01 Handshake Signal Schematic (Normally Installed
  51
  - NTMP01 Jumper Settings for J14 through J17
    51
  - NTMP01 Jumper Settings for J18
    51

Advertisement

Advertisement

Related Products

Bailey Categories

Control Unit Motorhomes Lighting Equipment Recording Equipment Controller

More Bailey Manuals