BETA Shell 4.0 Series User Manual

Lens case

Beta Shell™ 3.0 / 4.0 Series Lens Case User Manual

Thank you for purchasing one of our Beta Shell™ lens cases!

Your Beta Shell™ lens case is intentionally designed to be simple to use, yet provide superb protection to the

stored optical lens. From the experiences we photograph in our travels both far and near we have learned that

light is right and unnecessary complexity is a liability – these two core philosophies are what have guided our

Beta Shell™ lens case design.

We design, manufacture, and test our lens cases with the intent to exceed your expectations. If you are not

satisfied with your Beta Shell™ lens case, we offer a 30 day "no questions asked" return policy. Simply return

the unused Beta Shell™ lens case to us and we will refund the original purchase price. In addition, all our Beta

Shell™ lens cases come with our unconditional Bomb-Proof Guarantee – If any part of your lens case wears

out, breaks, or fails under intend use conditions we will replace or repair your Beta Shell™ at no cost – just get

the lens case back to us and we will take care of the rest! *

Included in with every Beta Shell™ lens case are the following items:

1) Beta Shell™ Lens Case

2) Extra foam disk insert(s) (series 4.0 only)

3) One small indicating Silica Gel Pack

4) User's Manual (this document)

5) One extra split ring (for strap attachement)

If one of the above listed items is missing. Please email us at

sales@betashell.com

Please read this product manual to get the most out of your Beta Shell™ case!

* Bomb-Proof Guarantee applies only to individual U.S. based customers (lower 48 states). We reserve the right to charge for return

shipping costs in some situatutions. We reserve the right to waive repairs if product was misused or damaged beyond reasonable repair.

 Product Liability and Disclaimer – Please Read 

It is your responsibility to protect your photographic equipment. The user shall determine the suitability of this product for his or her

use, and shall assume all risk of liability in connection with that use. Under no circumstance will Mogomoto Prototype LLC be held

responsible for damage to photo equipment arising from the use of this product. Neither Mogomoto Prototype LLC, it's suppliers,

subcontractors, dealers or agents are liable for any loss, injury, or damage whatsoever arising from the use of this product. Modifications to

your Beta Shell™ lens case will void the warranty. Never expose to excessive heat or petroleum based solvents. Never use this lens case

to carry or protect objects other than photographic equipment. Beta Shell™ cases are designed to be water-proof under test conditions.

Water penetration will occur if lid is not properly closed, set, worn, or is damaged. Normal wear and tear will compromise the function of this

product. Beta Shell™ lens cases are protected under U.S. patent right laws. Beta Shell™ lens cases are Patent Pending.

Rev. 0410-2

Table of Contents

Need help?

Do you have a question about the 4.0 Series and is the answer not in the manual?

Page 1 Modifications to your Beta Shell™ lens case will void the warranty. Never expose to excessive heat or petroleum based solvents. Never use this lens case to carry or protect objects other than photographic equipment.
Page 2 – read below to create a better fit. Fig. 1 – Checking the fit of lens inside Beta Shell™ case. End cap should be about flush with top of case. To close your lens case, gently press the lens down to “set” its location – then immediately gather the end cap with the memory foam attached to the Top Lid assembly.
Page 3 Beta Shell™ in a manner such that a 100% water-proof seal in achieved. You can easily verify a water-proof seal by submerging your Beta Shell™ (without a lens) in a buck of water. If air bubbles escape between the O-ring seal and the matting flat surface, then the Lid needs to be closed more tightly! Note –...
Page 4 If you plan to keep a lens stored inside a Beta Shell™ lens case for a long time make sure there is not any excessive moisture trapped inside the case and use a silica gel pack inside the lens case.

3.0 series