Advertisement
Quick Links
Advertisement
Related Manuals for Kanrich 915
Summary of Contents for Kanrich 915
- Page 1 915 2-wire video doorphone system User Manual Villa Type...
- Page 2 The Cable Specifications of 915 2-wire System CAT 5e STP with shield(aluminum foil) anti-interference Quality is the best and the distance up to 100M is still good ,with power line together without signal/video interference. Please pay much attention , there are 4 pairs in CAT5e , just use 2 pairs of them , other 2 pairs never to use it .
-
Page 3: Specifications
915C10AL Color Aluminum Camera Inside View Mic. White LED SPK. Resident 1 Call Button Resident 2 Call Button SW1 open door time(No.1) ← → 15 sec. 2 sec. BAL (never touch) Terminals MIC. Gain Clockwise SPK. Gain anticlockwise ─ Specifications : Working Voltage : DC 15V from PH-915P Current Consumption:... - Page 4 Flush Pre-box for model "AL" Camera 175/105/60mm Surface Pre-box for model "AL" Camera 210/125/60mm...
- Page 5 915CAL Aluminum Camera with CCD 915CALM Aluminum Camera & Mifare Card Reader Inside View Mic. SVR1 MIC. Gain Clockwise White The sensitive SVR2 SPK. Gain anticlockwise area of card reader Color SVR1 SVR2 SPK. open door time set Call Button 2 sec.
- Page 6 The user guide of Card Reader For CALM - Villa Type To add new cards: 1. To add cards: By Master REG (The Master Card for registering a new card or cards) green light flashing Steps: To swipe Master REG one time--beep-- --swipe new card(or cards)--beep in twice Successfully register new card (or cards), if you want to stop adding cards,...
- Page 7 915M35 3.5” Handsfree Color Monitor Handsfree Talking / Monitoring Button Handsfree Talking button Press for getting a call and talking . After talking press it again for finish. Monitoring button Press to start monitor screen and monitor door camera situation and also to talk with camera ,press it again for finish.
- Page 8 915Mi 4" Handsfree video monitor Code setting button/ Indicator(system in use) video dummy TFT screen Door Release 2 adjustment Door Release 1/ Resident Code setting button ringing tone / Door Status Indicator adjustment Handsfree Talking / Monitoring Buttons/Indicators Resident Code setting button When doorphone system is standby and press "...
- Page 9 915Mi 4" Handsfree video monitor Switch Ringing Tone Adjustment Video Dummy Up --- volume increase swich up ----OFF Middle --- volume middle switch down ---ON Down --- volume down Monitor Terminals rear view Speaker Monitor code setting steps : 1. When doorphone system is standby and press " "...
- Page 10 915M7 7” Handsfree video monitor ↑ + Calling Tone Volume Knob Side View Color Adj. Knob ↓ - Brightness Adj. Knob Power Indicator Power Indicator - green - power on "in use" indicator / Intercom Indicator (Red) This indicator is on - It means one of residents is using , spk.
- Page 11 915M7b 7” Touch Pad Handsfree video monitor Clock when the screen on and time is display, access to toolbar and choose for adjusting time. "in use" indicator / Intercom Indicator (Red) The red light on - It means one of residents is using ,please wait this resident finishing talking then to use .
- Page 12 Home Screen Handsfree Talking Line Line Open Door 2 Open Door 1 shooting in manual mode screen stop about 3 sec. then return Home Screen Intercom Intercom Inter-Call Inter-Call Home Screen Line Call control center 915M7b 2012 10月...
- Page 13 PS. "0" no take a picture / Home "1" one call, take one picture/ Picture Q'ty "3" one call, take 3 pictures Screen Picture 2012/ 12/ 12 12:12:12 0/1/3 different choice Rearward Forward 2012/ 10/ 10 10: 10:10 Picture Time Home Screen Choice...
- Page 14 915M3 Audio Handset Resident Code Setting / Main Handset & Sub-Handset Setting Resident Code Setting When doorphone system is standby and press " ", you will hear "Du" on 915M3 and on camera too. Please enter " resident code" on camera immediatel y, 915M3 will get this call and send "Ding-Dong"...
- Page 15 915Mg Audio Handset Code setting button/Main monitor & Sub monitor setting button Mic. Code setting button : When doorphone system is standby and press " ", you will hear "Du" on 915Mg and on camera ,too. Please enter "915Mg code"on camera immediately , 915Mg will get this call and send "Ding-Dong"...
-
Page 16: Power Supply
915P Power Supply 915P Fuse Power Indicator AC 250V Power In In / Out System Main Line AC 100-240V 47- 63HZ FGND System Main Line Power Output DC 15V /1500mA 2011 Sep.
Need help?
Do you have a question about the 915 and is the answer not in the manual?
Questions and answers