Pioneer GEX-P6400TV Installation Manual

GEX-P6400TV
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit
est conforme à CEMA.
Printed in Japan
Imprimé au Japon
<CRD3616-A> UC <KKYFF/02CD0001>
Installation <ENGLISH>
Note: OSD Switch Setting
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
Before installing, use a pen tip or other
up properly, and the unit and the system work
thin, pointed instrument to set the OSD
properly.
Switch on the right side of this product
• Use only the parts included with the unit to ensure
to the appropriate position for the com-
proper installation. The use of unauthorized parts
can cause malfunctions. ponent you are using it with.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.
• Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• When mounting this unit, make sure none of the
leads are trapped between this unit and the sur-
rounding metalwork or fittings.
• Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it.
(Never install in locations such as the above
Installing the Unit
because of the danger of malfunction due to high
temperatures.)
Adhere the hard Velcro tape (provided)
• Before drilling any mounting holes always check
behind where you want to drill the holes. Do not to the bottom of the hide-away unit and
drill into the gas line, brake line, electrical wiring
adhere the soft Velcro tape (provided)
or other important parts.
to the installation location.
• If this unit is installed in the passenger compart-
ment, anchor it securely so it does not break free This product
while the car is moving, and cause injury or an
accident.
• If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route all Velcro tape (hard)
leads and cords carefully around the sliding mech-
anism so they do not get caught or pinched in the
mechanism and cause a short circuit.
Velcro tape (soft)
Car mat or chassis
Note:
• Direct installation on the carpet is possible if the
hard Velcro tape will adhere to the carpet. Do not
use the soft Velcro tape in this case.
• Thoroughly wipe off the surface before affixing
the velcro tape.
Connecting the Units
Note: Disconnecting an AV-BUS connector
• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
When disconnecting an AV-BUS con-
ational vehicle, truck, or bus, check the battery
nector, grasp it firmly on both sides
voltage.
and pull towards you. This will unlock
• To avoid shorts in the electrical system, be sure to
the connector, enabling disconnection.
disconnect the ≠ battery cable before beginning
installation.
• Refer to the owner's manual for details on con-
necting the other units, then make connections
correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake
and seat rails. Do not route wiring in places that
get hot, such as near the heater outlet. If the insu-
lation of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to the vehicle
body.
• Don't pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing over heating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.
• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col-
ors correctly.
• To minimize noise locate the TV antenna cable,
radio antenna cable and RCA cable as far away
from each other as possible.
• Cords for this product and those for other
products may be different colors even if they
have the same function. When connecting this
product to another product, refer to the sup-
plied Installation manuals of both products
and connect cords that have the same func-
tion.
<ENGLISH>
Connecting the Power cord
This Product
Yellow
To terminal always supplied with power
Fuse holder
regardless of ignition switch position.
Black (ground)
To vehicle (metal) body.