Table of Contents
Advertisement
Quick Links
IN301 STATISTICS
PRINTER
OPERATOR'S MANUAL
Inscale Measurement Technology Ltd
7 Heron Close, St. Leonards-on-Sea. East Sussex TN38 8DX United Kingdom
+44(0)1424 200722
+44(0)1424 443976
Tel:
Fax:
Email:
sales@inscale-scales.co.uk
Http: www.inscale-scales.co.uk
Solutions in Weighing Technology
Inscale Measurement Technology Ltd follows a policy of continuous improvement and reserves the right to change specifications without notice. © October 2002
Advertisement
Table of Contents
Summary of Contents for Inscale IN301
- Page 1 7 Heron Close, St. Leonards-on-Sea. East Sussex TN38 8DX United Kingdom +44(0)1424 200722 +44(0)1424 443976 Tel: Fax: Email: sales@inscale-scales.co.uk Http: www.inscale-scales.co.uk Solutions in Weighing Technology Inscale Measurement Technology Ltd follows a policy of continuous improvement and reserves the right to change specifications without notice. © October 2002...
- Page 2 Shielded interconnect cables must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by Inscale could void the user's authority to operate the equipment. © Inscale 2000...
- Page 3 The printer comes preset to work with the default RS-232 interface found on the Inscale balances. It can easily be changed to work as a standard printer with other equipment. The printer is easy to use with only a paper feed button (grey button) and a print switch (red button).
-
Page 4: Specifications
20 meter roll maximum diameter 48mm. Size 60 x 180 x 150mm 0.6kg Interface RS-232 or RS-242 (TTL) 5 pin DIN Connector 1200, 2400, 4800 or 9600 baud 8 bit or 7 bit With or without parity © Inscale 2000... -
Page 5: Paper Loading
If the paper does not feed easily check you are using the paper entry slot and there are no obstructions in the paper path. Configuration Dip-Sw it ch Paper Loading Note direction of paper roll © Inscale 2000... - Page 6 The printer is set with the dip-switches under the paper roll, see drawing on page 3. When configured as a statistics printer it will work with the Inscale balances only. The data from the balances will be collected and statistical information on the readings from the balance can be printed.
- Page 7 5 pin DIN connector. 9 Pin D-Subminiature Socket Pin 1 RXD ----------- Pin 3 Data from Scale Pin 2 DTR ----------- Pin 1 Not used by Inscale balances Pin 3 GND ----------- Pin 5 Signal ground Pin 4 nu Pin 5 TXD -----------...
-
Page 8: Statistics Operation
The Statistics Report consists of the following information. number of results sum x sum of all results average standard deviation (n-1) srel relative standard deviation minimum value maximum value range (max – min) The equations used are: − srel = − © Inscale 2000... - Page 9 If the printer detects a change in format or an error during data collection a message of * Data Error * will be printed. If the message does not clear when the balance data is sent to the printer it may be necessary to turn the printer off/on before starting again. © Inscale 2000...
-
Page 10: Normal Printing
The baud rate and parity should be as set above regardless of how the printer is configured using the dip-switches. A program to set the date and time is available from Inscale. This program will run under Windows. Contact us for details. - Page 12 © Copyright by Inscale Measurement Technology Ltd. All rights reserved. No part of this publication may be reprinted or translated in any form or by any means without the prior permission of Inscale. Inscale reserves the right to make changes to the technology, features, specifications and design of the equipment without notice.