Proposition 65 State of California Warning ! Engine exhaust and some its constituents are known to the State of California to cause cancer, birth defects, and/or other reproductive harm. Notification of Spark Arrester Requirement for State of California It is a violation of Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order or the engine...
WARNING Concrete cutting produces dust and fumes Refer to the HDS60 Parts List in this manual known to cause illness, death, cancer, respiratory disease, birth defects, and/or other for additional information and part reproductive harm.
Keep all body parts away from rotating Always use diamond blades manufactured machinery. specifically for the HDS60 saw. Replace all guards and access panels Never cut dry. Without an adequate water (unless stated otherwise) prior to operating supply to properly lubricate the blade, the the saw.
Wear gloves and be alert to the surrounding environment when handling DO NOT install or remove the blade guard blades. with the saw running. When installing the blade, always fit the groove in the blade to the main drive wheel. ...
Technical Information Weight (without blade) -------------------------- 29.8 lbs. / 12.5 kg Width ------------------------------------------------ 10-1/4 in. / 260 mm Height (without the blade) --------------------- 19 in.. / 483 mm Length (without the blade) --------------------- 26 in. / 660 mm Power Requirement ----------------------------- Hydraulic Maximum flow ------------------------------------ 8 GPM / 30 l/min.
Page 8
Blade removal and installation Step 1: Remove blade guard and splash flap using 9/16” wrench provided (figure Figure 1 Step 2: Remove adjustable arm assembly (figure 2). Figure 2...
Page 9
Blade removal and installation Step 3: Relieve transmission assembly tension by pulling t-handle out and turning 90 degrees (figure 3) Figure 3 Step 4: Disassemble upper drive roller by locking roller and removing allen screw with the ¼” allen wrench provided (figure 4). Figure 4...
Page 10
Blade removal and installation Step 5: Hold transmission in neutral position and remove upper drive wheel and blade (figure 5). Figure 5 Step 6: Remove water injection plate with the 5/32” allen wrench provided. Note location of water injection holes prior to removing plate. Install new plate with water injection holes matching previous mounted location (outer right side opposite from drive wheel)(figure 6).
Page 11
Blade removal and installation Step 7: Inspect lower drive roller for wear on lip. Replace if lip is worn to half the original width (.200”)(figure 7). Figure 7 Step 8: Install new blade, matching groove in blade to lip on the lower drive roller.
Page 12
Blade removal and installation Step 9: With the transmission assembly in neutral position, reinstall upper drive roller using the ¼” allen wrench provided. Tighten securely by locking drive wheel in position (figure 9). Figure 9 Step 10: Using 5/32” allen wrench provided, remove guide roller cover and inspect both guide rollers for wear or damage.
Page 13
Blade removal and installation Step 11: Reinstall adjustable arm assembly, blade guard and splash flap on saw. Hand tighten bolts. Place ring saw on flat surface (figure 11) so that the adjustable arm assembly is sitting with the weight of the saw on it. Tighten bolts using the 9/16”...
Page 15
Diagram Part Quantity Number Number Required Description 6061241 BLADE GUARD ASSEMBLY (INCLUDES 1, 2, 3, 4) 6061188 BLADE GUARD 6061189 SPRING 6061190 UPPER GUARD 3a** 2903244 DOWEL PIN, 1/4" DIA X 1/2" 6061191 6061191 CLAMPING BLOCK CLAMPING BLOCK 6061242 ADJUSTABLE ARM ASSEMBLY (INCLUDES 5, 6, 7, 8, 9, 10, 39, 55) 6061192 ROLLER ARM 6061193...
Page 17
Diagram Part Quantity Number Number Required Description 6061226 COVER-GEAR BOX 6061227 STEM 6061228 VALVE CAP 6061229 SPRING 6061230 STEM BLOCK 2505125 2505125 O RING O-RING 2505126 SEAL-QUAD 2706791 SEAL-QUAD 2902985 SCREW, FLAT HEAD 1/4-20 X 1-1/4" 6061231 GEAR SMALL 6061232 GEAR LARGE 6061233 HOSE ASSEMBLY # 2...
Page 20
(1) year from the date of shipment to Customer. The responsibility of Diamond Products under this Warranty is limited to replacement or repair of defective parts at Diamond Products’ Elyria, Ohio...