Page 3
1.1 System Specification Recommendation The below is the recommended computer specification to work with X-Vision boards. Model XP4SW25 XP16SW50 – XP16SW100 XP16SW200- XP32SW200 Pentium Celeron 1.7GHz or above Pentium IV 2.0Ghz or above Motherboard Intel 865 Chipset Motherboard or above...
Page 4
We highly recommend you to set automatic daily rebooting in idle time for most stable system operation. 4) Operating System As PCDVR Server Software was built on Windows 2000 platform, it operates most stable on Windows 2000 platform. 5) DirectX DirectX Verison 8.1b or above X-Vision...
Page 7
2.2 XP4SW25 Formation : XP4SW25 board DI/DO Terminal TV Out Watchdog Terminal Camera Input 1 Camera Input 2 Camera Input 3 Camera Input 4 X-Vision...
Page 8
Audio Input Terminal To Motherboard Reset Terminal 16-Ch BNC Cable TV Out To PC Reset Switch Watchdog Cable Connection Remarks Two pcs of XP16SW50 cards can be installed in one system to get 32-ch camera inputs same as XP32SW200. X-Vision...
Page 9
For Back Panel Connetion Audio Card Connect Terminal 16-Ch BNC Cable TV Out Impedence Jumper Arrangment Impedence : match the impedence value of video signal TV Out to the analog TV monitor property. (Default) NC : no impedence matching from capture card. X-Vision...
Page 10
DI/DO Terminal Audio Card Connect Terminal 16-Ch BNC Cable TV Out TV Out Impedence Jumper Arrangment Impedence : match the impedence value of video signal to the analog TV monitor property. (Default) NC : no impedence matching from capture card. X-Vision...
Page 11
TV Out Audio Card Connect Terminal TV Out Impedence Jumper Arrangment Impedence : match the impedence value of video signal to the analog TV monitor property. (Default) 16-Ch BNC Cable Ch 5-8,13-16,21-24,29-32 NC : no impedence matching from capture card. X-Vision...
Page 16
- N/O : Normal Open - N/C : Normal Close - DI Operation Mode (N/O or N/C) can be selected from Setup Mode of Sentry Program - D/O Delay Time can be adjusted from Setup Mode of Sentry Program X-Vision...
Page 17
COM port of DVR. Then connect signal line from receiver to convertor. Select the correct protocol type from PCDVR Server program and match the address number of each PTZ camera to each one in PTZ setup in PCDVR Server Program. COM Port (RS232C) RS422/485 Converter X-Vision...
Page 19
- Remove any DVR Device Driver associated by BT878 : select to delete all device drivers relating BT878 (Usable when other brands capture using BT878 was installed previously) 3. Press OK. Then the system will reboot after completion. Device Manager View After Driver Installation X-Vision...
Page 20
3.2 DVR Program Installation 1. Run “Setup.exe” in the folder in the CD-Rom provided. 2. Click “Next” X-Vision...
Page 21
3. Specify the destination to install and click “Next” 4. Check on three options and click “Next” 5. Select the video type and click “Next” X-Vision...
Page 22
6. Now installation is being performed 7. . Now the installation has been finished. Click “Finish” to finalize. X-Vision...
Page 23
8. Then double click “PCDVR” icon on the desktop to run the program. And the board type selection menu will come up. Check on suitable board type from the list and click “OK” 9. Then “Recording Drive Setup” will come out. Select a drive available and select the recording type, “record or backup”. Then click “Apply” and OK”. X-Vision...
Page 24
PTZ Driver files exist Skin GUI skin file exists Sound Sound files (*.wav) used in DVR program exist Tools Utilities exist (Backup, Backup Player & CaptureClear) Update Temp folder for download when real-tim update WebPages Web files for web service exists X-Vision...
Page 25
- You can make image files and copy them to image folder. Note - In order to apply customized images from install stage, you can make image folder in installation folder (ex ; Server-2003XXXX) and copy the image files to the folder. X-Vision...
Page 26
FontStyle = 700 (Font Type Bold:700, Normal:400) [MESSAGE] Language change starts below this line. Input the term with your language on the right to “= “mark cancel = cancel yes = yes Ex ) yes = si (when changing from English to Italian) X-Vision...