Related Manuals for Jet JAT-501
Summary of Contents for Jet JAT-501
- Page 1 Pneumatic Mini HVLP Spray Gun #505501, JAT-501 Operation & Parts Manual M-505501 Edition 1 02/2015 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2015 JET...
-
Page 2: Warranty And Service
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. -
Page 3: Safety Warnings
10. The air tool must be properly lubricated before operating. Do not use this tool for other than its intended use. If used for other purposes, JET disclaims 11. Never start a percussion type air tool (chipper, any real or implied warranty and holds itself breaker, buster, etc.) without securing the... - Page 4 33. Do not lubricate the tool with combustible off the trigger, before connecting to air supply. liquids, such as kerosene, diesel or jet fuel. 24. Remove adjusting keys and wrenches before 34. Do not dispose of this tool with normal turning on tool.
-
Page 5: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
Any missing parts or damage should be reported ® immediately to your JET distributor. Do not use a NOTE: To reduce overspray and obtain maximum damaged tool. Read this instruction manual efficiency, always spray with the lowest possible thoroughly for operation, maintenance and safety air pressure/fluid flow combination. -
Page 8: Maintenance
Water in the air line may enter the tool and or water, depending upon material used. cause damage. Place cleaning solution into cup and install on gun. Spray solution through the gun until Change filters on the air system on a regular basis. JAT-501 Mini HVLP Spray Gun ... - Page 9 Air-line pressure increased Use safety shut-off valves so air flow can be accordingly to compensate for extra-long air stopped quickly in case of a line break. hoses (usually over 25 feet). Inside diameter When using multiple hoses, air hoses should be of hose should be minimum 3/8-inch.
- Page 10 Troubleshooting JAT-501 Mini HVLP Spray Gun Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Correct normal pattern. No correction necessary. Dirty or damaged air cap.
-
Page 11: Replacement Parts
Problem Possible cause Remedy Gun leaks from fluid Foreign substances between Disassemble and clean nozzle and nozzle. fluid nozzle and needle. needle. Paint emerges from needle Needle packing is damaged or Replace packing. packing. missing. Too much overspray. Gun too far away. Move gun closer to work surface. - Page 12 #505501, JAT-501, Mini HVLP Spray Gun – exploded view JAT-501 Mini HVLP Spray Gun ...
- Page 13 #505501, JAT-501, Mini HVLP Spray Gun – parts list Index Part No. Description Index Part No. Description JAT501-01 Air cap assembly 1.0mm 15 JAT501-15 Screw M2.6x5 JAT501-02 Fluid nozzle 1.0mm 16 JAT501-16 Air inlet 1/4in. PS JAT501-03 Plastic gasket 17 JAT501-17...
- Page 14 This page intentionally left blank. JAT-501 Mini HVLP Spray Gun ...
- Page 15 This page intentionally left blank. ...
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-501 Mini HVLP Spray Gun ...