Care And Maintenance - Mark Of Fitness MF 46 User Manual

The avarage of the stored result in the selected bank is displayed.
The latest result stored is displayed when there is only a single result and the clock display remains when there are no results stored.
The indication at the top of the display alternately changes from memory data number to date and to time.
The memory data is displayed for approximately 30 seconds. Approximately 30 seconds after MEMORY BUTTON is released, the
apparatus will turn off.
2 Press MEMORY BUTTON to move to next data.
The memory data number 1 is the latest among the stored data in the selected memory bank.
3 Every depression of the key switches among the memory data.
As MEMORY BUTTON is pressed, the memory data number increases; the bigger the number, the older the result.
4 Press ON/OFF BUTTON 2 and turn off the unit.
DELETING STORED DATA
Deleting a single data
1
Show the data to be deleted following
the steps in MEMORY FUNCTIONS.
2
Press and hold down MEMORY BUTTON
M1 3 or M2 4 whichever the data is
stored.
The displayed data starts flashing.
Hold down the button until the display
disappears.

CARE AND MAINTENANCE

Because the unit includes precision parts, care should be taken to avoid extreme temperature variations, humidity, shock, dust, and direct sunlight. Do not drop
or strike the unit. Make sure not to expose the unit to moisture. This unit is not water resistant.
Use only a soft, dry cloth to clean the unit. Do not use gasoline, paint thinner, or other strong solvents on the unit. Since the cuff may absorb perspiration and
other fluids, inspect it for stain and discoloration after each use. When cleaning the cuff, do not machine wash or scrub it. Use a synthetic detergent and gently
rub the surface. Make sure fluid never gets in AIR HOSE 10 . Air dry throughly.
When storing the unit, do not place heavy objects on it and do not coil AIR HOSE too tightly. When the unit has been stored at a temperature below the freezing
point, keep it for at least 1 hour in a warm place before using it. Remove the batteries if the instrument is to be stored for an extended period of time. Keep
MEMORY FUNCTIONS
see fig.6
Deleting all data in a bank
1
Press MEMORY BUTTON M1 3
and show the average of the bank to be
deleted.
2
Press and hold down selected MEMORY
BUTTON.
The displayed data starts flashing.
Hold down the button until the display
disappears.
GASOLINE
PAINT
THINNER
- 14 -
the batteries out of reach of children.
We suggest that you have your blood pressure monitor checked every 2 years. This operation may only be performed by the manufacturer or by firms
authorized by the manufacturer.
Do not inflate the cuff when it is not wrapped around your arm.
Do not disassemble or modify the unit.
ERROR DISPLAYS AND TROUBLESHOOTING
ERROR SYMOL / SYMPTOM
OVER-PRESSURIZATION
page 7
MEASUREMENT ERROR
or M2 4
INFLATION ERROR
DEFLATION ERROR
IMPROPER OPERATION
No display when ON/OFF BUTTON
is pressed.
2
Refer to "PARTS NAMES AND PRODUCT COMPONENTS" on page 2 for circled numbers:
CAUSE / CHECK POINT REMEDY
The cuff was inflated to the maximum pressure Do not move during measurement.
because of movement of body etc.
Measurement could not be made because of Remain still and quiet during measurement.
moving or talking during measurement.
TUBE PLUG is not correctly inserted. Reinsert TUBE PLUG
11
securely inserted.
Movement or talking was detected during Turn off the power and make another
measurement. measurement while being quiet and still.
ON/OFF BUTTON 2 was accidentally pressed Press ON/OFF BUTTON
during battery replacement. once and press it again to start a
measurement.
Have the batteries polarities been positioned Reinsert the batteries in the correct position.
incorrectly?
Have the batteries run down? Replace them with new ones.
Are the battery terminals clean? Clean the battery terminals with a dry cloth.
- 15 -
~
1 14
CARE AND MAINTENANCE
and make sure that it is
11
2 to turn off the power