Delkim RX Plus Getting Started

DELKIM Plus RADIO SYSTEM

GETTING STARTED

Before the system can be used the Rx Plus Mini Receiver must first be programmed
to recognise the users uniquely coded transmitters (Tx-i Plus or Tx Plus ). Normally
the user programmes the individual LED channels to match the LED colour of the
Delkim Plus Bite Alarm but this is not essential. The user can programme any colour
combination of Delkim Plus Bite Alarm into any channel of the Rx Plus irrespective of
RANGE &
LED colour, i.e. three blue LED Delkims may be programmed into red, white & blue
POWER SWITCH
LED channels on the Rx Plus if required.

PROGRAMMING

(Usually required once only unless additional transmitters are added to the system)
STEP 1 - Connect a PP3 battery, fit inside the battery compartment, close the door
VOLUME
and turn up the volume. Please note that the volume control is totally independent
from that on the Delkim Plus which can be set at zero, the recommended setting. For
optimum performance it is recommended to use a Duracell MN1604 battery.
STEP 2 - Switch on into either L (Local) or D (Distant), press and release programming
button, situated at the bottom right of the receiver back - Channel One LED starts
flashing (Purple Haze).
STEP 3 - If programming of the first channel is required, activate the first Delkim,
either automatically by just switching on or manually by vibrating the sensor to transmit
the code. When the code is accepted, it is confirmed audiby by a double tone and the
next channel's LED starts flashing. If the channel does not require programming,
press and release button once to skip to next channel.
STEP 4 - Repeat Step 3 until all required channels are programmed. To complete
programming skip over any unprogrammed channels which is confirmed visually by
all the LEDs giving a "Mexican Wave" flash and audibly by the musical switch-on tone.
(A short cut is to simply turn the Rx Plus off once all the desired channels are pro-
grammed and switch back on again).
STEP 5 - Check successful programming by switching on into either Local (L) or
Distant (D) and activating each programmed Delkim in turn as described in Step 3.
STEP 6 - Fit mounting clips or Velcro as required.
THE DELKIM Plus RECEIVER IS NOW READY TO USE - For programming of extra
or additional transmitters see ADVANCED PROGRAMMING.

RESET TO CLEAR PROGRAMME MEMORY

BATTERY
COMPARTMENT
If a channel has been programmed in error clear the memory of the Rx Plus and re-
programme :-
(If using a Tx Plus Micro Transmitter it can simply be re-fitted to the correct Delkim)
STEP 1 - Switch receiver off.
STEP 2 - Press and hold the programming button down and switch on the receiver.
STEP 3 - Continue to hold the programming button down until a "pip" is heard and
then release button. All the LEDs will start to flash.
PUSH
BUTTON
STEP 4 - Press and hold the programming button down, the LEDs will go out, wait
until another "pip" is heard and then release. The musical start up tone will be heard
and all the LEDs will flash in a double "Mexican Wave" effect. This confirms a
successful reset.
This procedure should always be used if you are in any doubt about what is
programmed and wish to start again. Full programming then has to be repeated.

USING THE RX Plus MINI RECEIVER

Simply switch on the Rx Plus Mini Receiver into either Local (L) or Distant (D) and set volume to required level.
To maximise battery life it is recommended to use Local (L) for all in swim situations where the range is up to 50 metres.*
Only use Distant (D) for occasional out of swim use over 50 metres*.
* Range will always depend on bankside obstructions, atmospheric conditions, positioning of transmitters & receiver and may vary
from unit to unit. The range check facility on the Tx-i Plus will give a rough guide to the reception range but as conditions change
constantly it should not be relied upon. USING A TRANSMITTER CLOSE TO THE GROUND MAY REDUCE THE RANGE. RAISING IT
BY JUST A FEW CENTIMETRES CAN GIVE A DRAMATIC INCREASE IN RANGE.