Table of Contents
Advertisement
Quick Links
Miller Easy Lift
Miller
and Miller Diving
®
Use of these terms to describe products that are not manufactured by Miller
Diving
is not permitted.
®
The two dimensional images (such as photographs and illustrations) of our
products are © copyrighted and trademarks of Morgan Diving Corp. The three
dimensional forms of our products are trademark/trade dress protected.
© ⅯⅯⅩⅡ Morgan Diving Corp. All rights reserved. This manual is made avail-
able for the express use of owner of this Miller Diving
manual may be reproduced, stored in any retrieval system, or transmitted, or
used in any form or by any means, whether graphic, electronic, mechanical,
photocopy, or otherwise by technology known or unknown, without the prior
written permission of Miller Diving
User Guide
Document P/N 100-902
Miller Diving
1430 Jason Way
Santa Maria, CA 93455, USA
Telephone (805) 928-7772
FAX (805) 928-0342
E-Mail: sales@millerdiving.com
Web Site: www.millerdiving.com
are all registered trademarks of Morgan Diving Corp.
®
Document #120613010
Harness
™
®
.
®
product. No part of this
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Miller Easy Lift
Summary of Contents for Miller Easy Lift
-
Page 1: User Guide
Miller Diving are all registered trademarks of Morgan Diving Corp. ® ® Use of these terms to describe products that are not manufactured by Miller Diving is not permitted. ® The two dimensional images (such as photographs and illustrations) of our products are ©... -
Page 2: Warranty Information
Should any part become defective, contact the nearest authorized Miller Diving dealer. If there is no dealer in your area, contact Miller Diving directly at (805) 928-7772. You must have a return authorization from Miller Diving prior to the return of any item, Upon approval from Miller Diving, return the defective part, freight prepaid, to the Miller Diving plant. -
Page 3: Table Of Contents
Weaving the vertical leg straps through the 3 hole adjustment buckle Inserting the leg buckles Disconnecting the leg buckles Maintenance of the Miller Easy Lift Harness ANSI Compliance ADCI Standards Notes © ⅯⅯⅩⅡ Miller Diving. All rights reserved. Document # 120613010... -
Page 4: Definitions Of Signal Words Used In This Guide
B WARNING Do not use the Miller Easy Lift harness in petroleum. The petroleum will attack the nylon material of the webbing which will result in the deterioration of the webbing and equipment failure. -
Page 5: Miller Easy Lift Harness Terminology
(yellow) leg strap leg strap buckles Replacement Assemblies 905-250 Leg Strap, Left, Sm- Med 905-251 Leg Strap, Right, Sm-Med 905-252 Leg Strap, Left, Lrg-XL 905-253 Leg Strap, Right, Lrg-XL © ⅯⅯⅩⅡ Miller Diving. All rights reserved. Document # 120613010... -
Page 6: Miller Diving
Miller Diving Ben Miller Ben Miller is the man behind the original designs of Miller Diving Equip- ment and a man dedicated to craftsmanship, quality and principles too often lost in today's world of mass production and imitation. Miller, a... -
Page 7: General Information
Miller Easy Lift Harness General Information General Information The Miller Easy Lift harness includes a rubber backpack to mount a bail-out cylinder, shoulder strap, chest strap, waist strap, leg straps, seat support straps and D-rings for umbilical and tool at- tachment. - Page 8 Note: The D-ring on the waist should hang freely on the outside of the lower arm strap webbing. Remove the harness and add the leg straps. © ⅯⅯⅩⅡ Miller Diving. All rights reserved. Document # 120613010...
-
Page 9: Installing The Leg Straps
Note: This will put the short end of the leg strap on the inside of the leg. Pull sleeve up over the loose ends of both straps, it will keep the end from coming out © ⅯⅯⅩⅡ Miller Diving. All rights reserved. Document # 120613010... -
Page 10: Weaving The Vertical Leg Straps Through The 3 Hole Adjustment Buckle
Make a loop with the strap and push strap down through slotted hole #3 on the inside of the existing buckle strap that holds the buckle to the harness. © ⅯⅯⅩⅡ Miller Diving. All rights reserved. Document # 120613010... - Page 11 From the #2 slot push the strap down through #1 slotted hole on the inside of the existing vertical strap. e. Tighten strap and pull sleeve over both straps. The vertical strap will have the short end behind the vertical strap. © ⅯⅯⅩⅡ Miller Diving. All rights reserved. Document # 120613010...
-
Page 12: Inserting The Leg Buckles
✓ Incorrect male buckle direction Correct male buckle direction The leg straps should fit comfortably snug. Adjust these straps as necessary. © ⅯⅯⅩⅡ Miller Diving. All rights reserved. Document # 120613010... -
Page 13: Disconnecting The Leg Buckles
This will release the leg strap. Maintenance of the Miller Easy Lift Harness The Easy Lift harness is made using high tensile strength nylon webbing and heavy duty stainless buckles and D-rings thereby minimizing maintenance. However, it is essential to thoroughly inspect the harness for damage and wear before and after each dive. -
Page 14: Ansi Compliance
ANSI Compliance The Miller Easy Lift Harness and Extraction Bridle have been tested and meets all criteria for ANSI Z359.1 standards ADCI Standards The Miller Easy Lift Harness and Extraction Bridle meet the ADCI Consensus Standards 6 Edition, section 6.3.4 harnesses. -
Page 15: Notes
Miller Easy Lift Harness Notes Notes © ⅯⅯⅩⅡ Miller Diving. All rights reserved. Document # 120613010...
Need help?
Do you have a question about the Easy Lift and is the answer not in the manual?
Questions and answers