1. Manuals
  2. Brands
  3. Apxalarm Manuals
  4. Security System
  5. APX32EN
  6. Quick start manual

Apxalarm APX32EN Quick Start Manual

Hide thumbs Also See for APX32EN:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual See also: Programming Manual
APX32EN is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N
U U U U L L L L
LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.
Introduction
This Quick Start Guide can help you install the rechargeable APX32EN quickly and easily by providing the basic
steps for installation using the built-in defaults. For more detailed information and important notes, refer to the
APX32EN Installation and Setup Guide.
Installing APX32EN
Installation and Electrical Connections
Step
1.
Install the control as follows:
a.
Separate the front assembly from the back plate and disconnect the cable from the front assembly board.
Note: Disconnect the cable only from the front assembly board, not from the terminal block PC board.
b. Mount the back plate.
2.
Make wiring connections as follows:
a.
Connect the incoming phone line to either the 8-position jack or terminals 2 (TIP) and 3 (RING).
b. Connect the handset phone lines to either the RJ11 jack or terminals 4 (TIP) and 5 (RING).
Note: For full line seize operation, see the installation instructions.
c.
If used, connect a piezo sounder to terminals 10 (+) and 11 (–).
d. If used, connect a bell to terminals 11 (–) and 12 (+).
e.
If used, connect the IP or GSM communications device to the Alarmnet LRR/IP communications port.
f.
Connect wires from the K10145X10 AC Transformer to terminals 15 and 16.
3.
Make battery connections as follows:
a. Remove battery retainer.
b. Remove backing from tape on back plate.
c. Insert battery pack into back plate.
d. Install battery retainer.
e. Connect battery connector to receptacle on terminal block PC board.
f.
Carefully reconnect the ribbon cable to the front assembly PC board connector (properly aligning the red
wire).
g. After all wiring connections have been made, snap the front assembly to the back plate so it is held by the
locking tabs.
h. Plug the transformer into a 24-hour, 110VAC unswitched outlet.
Note: Rechargeable batteries may take up to 48-hours to fully charge. "LOW BAT" message should clear within
four hours, or by entering Test Mode.

Security System

Quick Start Guide

Action
K14117-8
11/07 Rev. A
APX32EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the APX32EN and is the answer not in the manual?

Questions and answers

Related Manuals for Apxalarm APX32EN

Summary of Contents for Apxalarm APX32EN

  • Page 1: Security System

    LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed. Introduction This Quick Start Guide can help you install the rechargeable APX32EN quickly and easily by providing the basic steps for installation using the built-in defaults. For more detailed information and important notes, refer to the APX32EN Installation and Setup Guide.
  • Page 2 FOLLOWING INTEGRAL RECHARGEABLE PROPER OPERATION BATTERY PACKS: OF THIS SYSTEM DATA P/N LYNXRCHKIT-SC NOTE P/N LYNXRCHKIT-HC USE ONLY THE K10145X10 P/N LYNXRCHKIT-SHA TRANSFORMER PROVIDED ONLY REPLACE EVERY FOUR YEARS CONNECTIONS * WHEN AVAILBLE 09012-010-V0 APX32EN WIRING CONNECTIONS - 2 -...

  • Page 3: System Programming

    Enter Programming mode: Installer Code + 8 0 0 Set a programming default as follows: Press *97, then press number 1 to select default table. Refer to APX32EN Programming Default Tables. Program the variable data fields as follows: RF House ID - Press *24, then enter the desired 2-digit RF House ID for wireless keypads.
  • Page 4 Step Action Serial Number - This prompt can be used to enroll the transmitter serial number via RF (Cont.) transmission or manually. If using RF Learning proceed to c. 1). If using the manual mode skip to c. RF Learning – Two (2) transmissions (two key depressions at least five second apart) will be required for BR type or four (4) transmissions (fault, restore and fault, restore) for UR or RF type.
  • Page 5 APX32EN PROGRAMMING DEFAULT TABLES For programming data values and Powerline Carrier Devices other than those listed in the default tables, see the Installation Instructions. Function Default Value Installer code 4112 Quick arm enable Keypad backlight timeout Forced bypass RF house ID code...

  • Page 6: 5800 Series Transmitter Loop Numbers

    Zone Default Value front door back door window motion detector ------- ------- ------- ------- loop 3 arm away loop 2 disarm loop 4 arm stay loop 1 no alarm response loop 3 arm away loop 2 disarm loop 4 arm stay loop 1 no alarm response duress silent alarm...

  • Page 7: Security Functions

    Keypad Functions (when default programming is used) Security Functions Checking system status: STATUS (high level messages); press STATUS again for secondary messages. To arm in STAY mode: Press and hold down STAY (or enter your code + STAY ) See note below. To restart exit delay: STAY (applies only if system is armed in Stay mode and Quick Exit option has been enabled) To arm in AWAY mode: Press and hold down AWAY (or enter your code + AWAY ) See note below.

  • Page 8: Speakerphone Operation

    In addition, if the system is armed by pressing and holding the Quick-Arm buttons, neither the Babysitter Code nor the Installer Code can disarm the system. REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE LIMITATIONS OF THIS SYSTEM AND WARRANTY INFORMATION. 5132 North 300 West Provo, Utah 84604 (800) 216-5232 www.apxalarm.com ÊK14117-8~Š K14117-8 11/07 Rev. A...

Table of Contents