Table of Contents
Advertisement
Quick Links
REVO - LOW PROFILE 35 DRILL
WARNING !
When using electric power tools
basic safety precautions should
always be used to reduce the risk
of fire, electric shock and personal
injury.
ORIGINAL INSTRUCTIONS
G&J Hall Ltd, Burgess Road, Sheffield, S9 3WD, England
Tel: +44 114 254 3206
Email: info@gjhall.co.uk
www.revo-tools.co.uk
Machine shown
REVO Low Profile 35
Fax: +44 114 244 9256
Web: www.revo-tools.co.uk
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Revo Low Profile 35
Summary of Contents for Revo Low Profile 35
- Page 1 REVO - LOW PROFILE 35 DRILL ORIGINAL INSTRUCTIONS Machine shown REVO Low Profile 35 WARNING ! When using electric power tools basic safety precautions should G&J Hall Ltd, Burgess Road, Sheffield, S9 3WD, England always be used to reduce the risk...
- Page 2 Good balance for Carrying Crank Lever Quick-release tool holder Annular cutter (Not included) Pilot pin (Not included) LED Work Light Motor switch Magnet switch Standard Accessories Power 1100W * Wrench M8 Voltage See machine nameplate * Hex. Key M2.5 No Load / Full Load min 650 / 390 Max.
- Page 3 WARNING! Read and understand all instruction before operating any drilling system. Failure to follow all instructions listed below may result in electrical shock, damage to drilling system and even personal injury. GENERAL SAFETY INSTRUCTIONS Work area Keep your working area clean and well lit. Cluttered benches and work stations or dark work areas can cause accidents.
- Page 4 Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.
- Page 5 Symbols used in this manual IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Terminology used in the manual 1.
- Page 6 SPECIFIC SAFETY RULES AND REGULATIONS Always use safety chain. Mounting can release. The magnet’s adhesion depends on the thickness of the work piece. Always ensure that the work piece is a minimum of 12mm (7/16 in.) thick. If it is not, then use a piece of steel plate at least 12mm thick and larger than the magnet below the work piece to supplement the magnetic adhesion.
-
Page 7: Operation-General
MOUNTING ANNULAR CUTTERS CAUTION: Never use a cutting tool that is larger than the maximum rated capacity of the machine. 1. To insert an annular cutter, first insert the pilot pin into the cutter. 2. Whenever mounting or removing cutters, always unplug the machine. 3. -
Page 8: Release Button
The crank handle offers tremendous leverage; so do not use too much force. Allow the cutting tool to determine the pace. With experience, the operator will be able to determine the best pace to feed to the work. There should be some degree of audible slowing of the motor but not bogging in the cut. Correct cutting speed with a properly sharp annular cutter will produce long unbroken chips, which produce a “bird’s”... -
Page 9: Maintenance
THE OPTIONAL LED WORK LIGHT Models equipped with the optional LED WORK LIGHT have a light which is always on whenever the machine is plugged in. This can be useful when working in dark work spaces. LED Work Light CAUTION: Never attempt to re enter a half-finished cut if the magnet has been turned off and the machine shifted in the interim. -
Page 10: Carbon Brushes
THE CARBON BRUSHES The carbon brushes are a normal wearing part and must be replaced when they reach their wear limit. Caution: Always replace the brushes as a pair. To replace: 1. Remove the 4 screws and remove the motor tail cover. 2. - Page 11 Wiring...
-
Page 12: Exploded View
Exploded View... -
Page 13: Parts List
PARTS LIST ITEM PARTS NAME PART No. ITEM PARTS NAME PART No. INTERNAL CIRCLIP R-19 22X01 SOCKET CAP SCREW M6 x 30 22X57 ARBOR WASHER Ø10 x Ø18.5 X 0.8 22X02 SPRING WASHER M6 22X58 COOLANT SEAL Ø10.2 x Ø12 x 15 22X03 LED LAMP 22X59... -
Page 14: Ce Declaration Of Conformity
CE Declaration of Conformity On our sole responsibility we declare that this product, the REVO Tools Low Profile 35 Drill, meets the basic requirements with the following standards and directives:- DIN EN 61029 (VDE 0740 Teil 500):12 2003 DIN EN 55014-1: 2007-06...
Need help?
Do you have a question about the Low Profile 35 and is the answer not in the manual?
Questions and answers