Dean La Jolla Passive Installation Instructions

LA JOLLA
Passive Model 3105
S S
T E R E O O U N D H O L E
P
I C K U P
M M & & P P P P
A A G G N N E E T T I I C C I I E E Z Z O O I I C C K K U U P P S S
E E I I
A A S S Y Y N N S S T T A A L L L L A A T T I I O O N N
Dean Markley's La Jolla Passive
™ ™
both the Dean Markley Tahoe sound hole pickup and the Dean Markley
™
Barstow Gold-Plated Under-The-Bridge-Saddle
™
dual system allows tone benefits from each style of pickup. In this stereo
arrangement, each pickup may be equalized separately for a fat, rich tone.
The Tahoe sound hole magnetic pickup will produce excellent bass and
™
mid-range response, while the transducer will provide you with more
transparent mid-range and glassy highs. In the past, guitarists have
"improvised" similar systems, but the La Jolla
complete stereo unit with "voiced" and matched components.
O F
UTSTANDING EATURES OF
• Tahoe ™ magnetic sound hole pickup features individual string balance
adjustment screws
• Qwik-Knx connector allows easy installation and removal of your
™
Tahoe
™
• Barstow ™ Under-The-Bridge-Saddle
connector
• 24-K Gold-Plated End-Pin Jack
• 6 Individual string sensors for independent string response
• Sensors mounted in 24-K Gold-plated steel casing, providing a level
surface for balanced string volume
• Quick & easy, solderless, mini-plug connectors
P E
ARTS NCLOSED
(1) Tahoe ™ magnetic sound hole pickup with male Qwik-Knx
(1) Gold-Plated Barstow Under-The-Bridge-Saddle
™
solderless mini-jack connection
(1) 24-K Gold-plated End-Pin Jack
(4) Stick-on flexible metal, cable ties with adhesive backing
T N
OOLS EEDED
1/8" (3.175 mm) drill bit
3/16" (4.763 mm) tapered step bit
9/16" (14.288 mm) open-end wrench
#1 Phillips head screwdriver
3/32" (2.381 mm) Allen wrench
Piece of string – 16" (40.64 cm) length
15/32" (11.906 mm) tapered reamer (optional)
1/8" (3.175 mm) drill bit
Fine Tooth Metal File
Sandpaper, 120 grit
& T
R A N S D U C E R
S
Y S T E M
• • W W F F S S O O
I I R R E E D D O O R R T T E E R R E E O O U U T T P P U U T T
• • S S C C
O O L L D D E E R R L L E E S S S S O O N N N N E E C C T T I I O O N N S S
is a true stereo pickup system. It includes
transducer pickup. This
™
Passive is truly the first
™ ™
L J P
™ ™
A OLLA ASSIVE
™ transducer with mini-plug
™
™ connector
transducer with
™
with female Qwik-Knx connector
™ ™
D M
EAN
3350 Scott Blvd. #45 • Santa Clara, CA 95054
1-408-988-2456 • 1-800-800-1008 • Fax 1-408-988-0441
www.DeanMarkley.com • Email info@DeanMarkley.com
©Nov2003 Dean Markley Strings, Inc.
I
NSTALLATION
Most guitar players realize that the investment in their prized guitar deserves
a professional installation of the La Jolla
be only a fraction more if you have your La Jolla
someone who is experienced in pickup installation.
You can install the La Jolla Passive
™
some knowledge of basic guitar mechanics. The La Jolla
uniquely designed for simple installation and requires no soldering for
ordinary applications.
NOTICE: Installer assumes all responsibility for damage to the La Jolla
guitar components. Be certain you read and fully understand all
instructions. Have a clear, clean workspace to do the installation. Use tools
in strict accordance with the manufacturer's recommendations and
warnings. When in doubt, seek the advice of a qualified guitar specialist.
Read ALL directions thoroughly BEFORE starting installation!
Part I – Installing the Barstow ™
Before you get started, it is imperative that the bottom of your saddle slot is
flat and uniform. If it is cut unevenly or warped, this may cause a string
volume balance problem. It is recommended that if your slot is uneven, you
take it to a professional technician to address the problem.
Start by removing all of the strings, one at a time. Don't cut your strings off
unless you loosen them first. The resulting jolt that the neck takes if the
strings are cut before loosening is not good for the neck.
Before removing the bridge saddle, take a sharp pencil and make a mark on
the saddle all along where the saddle meets the bridge. Now remove the
bridge saddle.
1. Correctly installed, each string should pass over the center of a string
transducer. Keeping that in mind, correctly position the transducer by lining
up the transducer with the string peg holes. On the bass side of the bridge
saddle slot, a 1/8" hole must be drilled for the transducer wire to go
through. Mark the spot in the saddle slot for the transducer wire's hole. Drill
with 1/8" drill bit, using care to maintain a 90-degree angle from the top of
the guitar. It is important that you drill straight so as to not widen the
existing slot on either side. Remove any wood chips and foreign material
from the saddle slot.
S , I .
ARKLEY TRINGS NC
I
NSTRUCTIONS
Passive . Your full investment will
™ ™
Passive™ installed by
™
yourself if you have patience, care, and
™
Passive
™ ™
Under-The-Bridge-Saddle ™ Transducer
has been
™ or