Set Lnb Power; Lnb Setup; Signal Setup; Tune Dsd - UEC DSD 700 Operating Instructions Manual

Set LNB Power

In most installations the correct setting for the LNB Power is "On".
Certain special applications may require the setting to be "Off".
To set the LNB Power "On" or "Off", do the following:
1 Press MENU on the RCU.
The Main Menu options list is displayed.
2 On the RCU, press to highlight Advanced Options.
3 Press OK.
The Advanced Options Menu is displayed, in which the Change
Dish Installation option is highlighted.
4 Press OK.
The PIN Code for Installation screen is displayed.
5 Type the PIN code 9949 using the keypad on the RCU. See
Note. After successfully entering the installation PIN, the Change
Dish Installation Menu is displayed, in which the LNB
Configuration option is highlighted.
NOTE: 9949 is the installation PIN code. A different PIN code is
required for the Parental Guidance PIN .
6 Press OK.
The LNB Configuration Menu is displayed, in which LNB Setup 1
highlighted.
7 Press OK. The Set LNB Power screen is displayed.
8 Press OK to save ON setting, or press
to OFF.
9 Press OK to activate the setting.
The Change LNB Settings Menu is displayed.
10 Press EXIT to return to the previous menu or MENU to return to
the service.

LNB Setup

The LNB mode and frequency or frequencies must be appropriate for
the LNB installed on the satellite dish. The information is supplied with
the LNB.
To set the frequency:
1 Repeat steps 1 to 6 of Set LNB Power (page 21).
2 Press to highlight LNB Mode.
3 Press to highlight LNB frequency.
4 Press OK.
The LNB Configuration menu screen is displayed. Press EXIT.
5 The Change Dish Installation menu screen is now displayed.
6 Press to highlight Signal Setup, then press OK.
7 Signal Setup 1 (home) is now highlighted on the Signal Setup
menu. Press OK.
8 The Signal setup screen displays the parameters for the
particular signal source, and also shows the configuration of
the selected LNB.
22
Signal Setup Alternatives
The factory preset values will normally not require changing. If, how-
ever, it is necessary to insert values for other signal sources, it is
recommended that you contact your local installer.

Tune DSD

If the settings made in LNB Configuration and Signal Setup are satis-
factory, retune the decoder with these settings as follows:
1
2

Reset to Factory Defaults

If difficulty is experienced in the functioning of the decoder, it may be
advisable to reset the factory defaults. This is achieved by selecting
the Reset Factory Defaults then pressing OK.

LoopThrough Mode

The Loop through Mode is used when the installation is using DiSEqC
control of LNBs. In a normal setup, it is not important whether this is
Enabled or Disabled. If DiSEqC LNB is used, consult your installer.

Signal Detection

to set the LNB power
This facility is used to help final alignment of the satellite dish and to
confirm that a signal is being received from the satellite.
NOTE: For LNB adjustment refer to the LNB installer. The
1
2
3
4
5
6
7
8
9
OPERATING INSTRUCTIONS
Press to highlight Tune DSD.
Press OK.
A rotating bar on the decoder front panel indicator indicates that
it is searching for the default frequency. The decoder then
returns to the current service, and the Information Bar and Clock
are displayed for the preset period of time.
decoder signal detection facility is only useful for final
alignment of a dish that is already aimed roughly at the
satellite. If there is no signal the bars will not be
present.
Press MENU on the RCU.
The Main Menu options list is displayed.
On the RCU, press to highlight Advanced Options.
Press OK.
The Advanced Options Menu is displayed.
Press to highlight Signal Detection.
Press OK.
The Signal Detection screen is displayed. The screen shows
the service provider name and the strength of the signal.
Adjust the alignment of the dish to obtain the maximum signal
strength as indicated by the bars on the screen. Press
to toggle between the coarse and fine tuning.
Physically lock the dish into position, then re-check the signal
detection.
Press OK.
The Advance Options Menu is displayed.
Press EXIT to return to the Main Menu or MENU to return to the
service.
and
DSD 700