Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Phoenix Audio Spider MT502 PSTN
- Page 1 Spider MT502 PSTN USER MANUAL Page 1...
-
Page 2: Table Of Contents
INDEX Overview .............Page 03 Connecting the Spider .............Page 04 Using the Spider .............Page 05 • Dialing .............Page 05 • Incoming Call .............Page 05 • During A Call .............Page 06 Display .............Page 07 Device Menu .............Page 08 External Mic/Speaker .............Page 12 Daisy Chaining .............Page 14 Specifications... -
Page 3: Overview
SPIDER 502 PSTN OVERVIEW The Spider is a high-quality conference speakerphone that will turn any room into a professionally sounding conference room. It has an exceptionally large pickup and broadcasting range, yet is small in size and discreet in design. The Spider utilizes multiple microphones, a uniquely designed speaker, and a powerful DSP to achieve commanding performance. - Page 4 Once you plug the Power Supply into a power source, your Spider is ready for use. No additional drivers or steps are needed. However, we do recommend downloading and using our “Phoenix Audio Setup Utility” for optimal audio control and performance. This utility can be found on our website: www.phnxaudio.com/downloads/audiosetup/...
-
Page 5: Using The Spider
CONNECTING TO AN ANALOG PHONE LINE For any session using a PSTN/POTS/ANALOG phone line. ‣ Using the telephone cable provided, plug one end of the cable into the Spider’s RJ11 telephone jack (TEL connector located on the connector panel below the unit). ‣... -
Page 6: During A Call
DURING A CALL THE DIRECTIONAL ARRAY During a call the Spider uses a proprietary Beamforming technology to locate a legitimate voice source, and to steer an array towards it. This allows the Spider to focus on the speaker in the room and to cancel out all other noises. -
Page 7: Display
DISPLAY DISPLAY SETTINGS Can be found in the Settings section of the MAIN MENU (see page 11.) DISPLAY TIMEOUT The amount of time before the unit’s display and keypad dim off. DISPLAY BRIGHTNESS Scroll using the buttons to choose a display brightness setting. GRILL LIGHT Turn ON/OFF the blue and red lights that appear under the grill during a call (incoming call, mute, Beamforming, and hanging up). -
Page 8: Device Menu
SET CALLER ID STANDARD For caller ID to work properly, you must set the Spider to match with your service provider’s standard. ‣ Enter the MAIN MENU by clicking on the button. ‣ Scroll using the buttons and select Settings press 7. - Page 9 NAVIGATING THE MENU ENTER button functions as ENTER and will take you one step forward in the menu. BACK The right function key is BACK and will return you one step back in the menu. EXIT button will EXIT the menu and will return you to the Spider’s main display. MENU CATEGORIES CALL LOG The Spider’s call history.
- Page 10 PHONE BOOK Store up to 100 contact names and numbers. You can clear the whole phone book by selecting the middle function button in the main menu, or clear a specific call by using the middle function button inside the PHONE BOOK. You can scroll through the lists using the buttons, and dial the number by selecting it with the...
- Page 11 SETTINGS General device controls and settings. Restore Defaults Returns all settings to factory defaults. Display Timeout The amount of time before the unit’s display and keypad dim off. Display Brightness Scroll using the buttons to choose a display brightness setting. Grill Light Turn ON/OFF the blue and red lights that appear under the grill during a call (incoming call, mute, Beamforming, and hanging up).
- Page 12 INFORMATION Firmware Version The firmware version that the Spider is running. The Spider’s serial number given by Phoenix Audio Technologies. An internal ID number. CONNECTING AN EXTERNAL MIC AND SPEAKER MICROPHONE ONLY Connect the external microphone to the 3.5mm connector using a 3-pin to 4-pin adapter (the same adapter that is used to connect a standard microphone to a Smart device).
- Page 13 PRIVACY MODE When using a mic’d headset, you can utilize the standard headset button to toggle between Privacy Mode (Headset Audio) and Speakerphone Mode. This allows you to leave your headset (or handset) plugged into the device when using the Spider’s built-in microphone and speaker. When in Privacy Mode the two front red LEDs will blink.
-
Page 14: Daisy Chaining
DAISY CHAINING Every Spider comes with a built in ability to connect to other SMART Spiders (MT503) or Quattro3s (up to 15 units). This feature enables you to provide coverage for larger spaces using a chain of units. NOTE: The PSTN Spider MT502 can only act as the first or “master” unit and not as a satellite unit. - Page 15 MAKING THE CONNECTION ‣ The PSTN Spider will be the master unit. This unit will be the one interfacing for the entire chain. The master unit will be the only unit communicating with an external device, while all other units will connect and communicate only with each other. ‣...
-
Page 16: Specifications
SPECIFICATIONS • USB interface (micro B connector) • 3.5mm external loudspeaker and microphone jack • Daisy chain expandability of up to 15 units • Three-way bridging capability • Frequency response 50Hz – 16KHz • Low latency (10ms) • Broadcast level (peak): 92dB SPL @1m (5 watts RMS) •... -
Page 17: Warranty
The following warranty statement is effective for all Phoenix Audio Technologies’ products as of October 1st, 2007 Phoenix Audio Technologies warrants that this product is free of defects in both materials and workmanship. Should any part of this product be defective, the Manufacturer agrees, at its option, to repair or replace with a like new replacement any defective part(s) free of charge (except transportation charges) for a period of two years for all products.
Need help?
Do you have a question about the Spider MT502 PSTN and is the answer not in the manual?
Questions and answers