MTL 9469-ETplus Instruction Manual

108mbps wireless bridge/access point

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

9469-ETplus

108Mbps Wireless Bridge/Access Point

Instruction Manual

INM9469

Table of Contents

Need help?

Do you have a question about the 9469-ETplus and is the answer not in the manual?

Questions and answers

Summary of Contents for MTL 9469-ETplus

Page 1 9469-ETplus 108Mbps Wireless Bridge/Access Point Instruction Manual INM9469...
Page 2 INM9469-3 June 2012...
Page 3: Table Of Contents
CONTENTS FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 DESCRIPTION .
Page 4 INM9469-3 June 2012...
Page 5: Features
9469-ETplus IS Wireless Access Point/Bridge INM9469-3 June 2012 FEATURES ♦ Intrinsically Safe ATEX / IECEx certified / FM / FMC approved ♦ Ga Ex ia IIC T4 GD (surface), Ma Ex ia I M1 (mining) ♦ Zone 1 / Division 1 mounting in a suitable enclosure ♦...
Page 6: Description
DESCRIPTION The 9469-ETplus 108Mbps Wireless Bridge / Access Point is a dual functionality module. When used in the Access Point (AP) mode, it allows wireless devices to connect through it onto the wired Ethernet network, either in Ad-hoc or Infrastructure modes. When used as a Bridge, it makes it possible to turn any 10/100 Ethernet device into a wireless device, or to connect two network segments together to make a single network (without the interconnecting wire or fibre optic).
Page 7: Electrical Connections
3 .3 Electrical connections DC power can be supplied to the equipment through the front panel screw terminals or alternatively using the Power over Ethernet (PoEx) option where DC power is supplied from a 9466-ET module down the Ethernet Cat5e (or Cat6) cable into the RJ45 connector on the front panel. WARNING: Whichever wiring method of powering the modules is used, the supply to them must be derived from a suitably certified, intrinsically safe supply.
Page 8: Getting Started
WiFi equipment (set in “infrastructure” mode) to connect into a wired Ethernet network. 4 . 1 .2 . Bridge In this mode, the 9469-ETplus gives wired Ethernet output equipment access to a WiFi network. (Use “infrastructure” mode to connect to an existing access point, otherwise use “adhoc” mode.) 4 .2 .
Page 9: Web Configuration
Note. If the device is behind a gateway the locator program will not find it. Use a computer on the same local network as the device for initial setup. If a firewall is installed on the computer ensure that UDP port 17784 is not blocked WEB CONFIGURATION To configure the device, run the administration web page.
Page 10: Maintenance & Troubleshooting
For more detailed information about the take-back and recycling contact MTL. TECHNICAL Ethernet LAN...
Page 11: Accessories
FM CERTIFICATION INFORMATION Special Condition of Use - Factory Mutual (USA & Canada) ♦ The Model 9469-ETplus shall be installed in compliance with the enclosure, mounting, spacing and segregation requirements of the ultimate application. ♦ The Model 9469-ETplus shall be excluded from use in environments containing chemical vapours of the Ketone or Ester families.
Page 12: Atex & Iecex Certification Information
ATEX & IECEX CERTIFICATION INFORMATION The following information is in accordance with the Essential Health and Safety Requirements (Annex II) of the EU Directive 94/9/EC [the ATEX Directive - safety of apparatus] and is provided for those locations where the ATEX Directive is applicable. General a) This equipment must only be installed, operated and maintained by competent personnel.
Page 13 INM9469-3 June 2012...
Page 16: Measurement Technology Limited
Tel: +39 (0)2 61802011 Fax: +39 (0)2 61294560 E-mail: info@mtl-inst.it 3413 N. Sam Houston Parkway W. Suite 210 Houston TX 77086 Tel: +1 281 571 8065 Fax: +1 281 571 8069 E-mail: csinfo@mtl-inst.com Group Internet home page http://www.mtl-inst.com/ Members of The MTL Instruments Group...