Related Manuals for Ryobi RPW3200
Summary of Contents for Ryobi RPW3200
- Page 1 RPW3200 PETROL POWERED HIGH PRESSURE CLEANER OPERATOR'S MANUAL ORIGINAL INSTRUCTIONS Important! It is essential you read the instructions in this manual before starting and operating this machine. Subject to technical modifications.
- Page 2 DESCRIPTION 19. Hose storage 35. Oil cap/dipstick 1. 5-in-1 Change Over Nozzle 20. Hex nut 36. Upper fill level 2. Detergent tank 21. Washer 37. Funnel 3. Spray wand 22. Trigger handle holder 38. Recoil starter 4. Fuel valve 23. Spray wand holder 39.
- Page 3 Fig.4 Fig.5 Fig.6 Fig.7 Fig.8 Fig.9...
- Page 4 Fig.10 Fig.11 Fig.12 Fig.13 Fig.14 Fig.15...
- Page 5 Fig.16 Fig.17 Fig.18 Fig.19 Fig.20 Fig.21...
- Page 6 Fig.22 Fig.23...
-
Page 7: General Safety Rules
■ Check damaged parts. Before further use of the GENERAL SAFETY RULES tool, a guard or other part that is damaged should be carefully checked to determine that it will operate WARNING properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, Read and understand all instructions. -
Page 8: Special Safety Rules
poorly ventilated area. SPECIAL SAFETY RULES ■ Never store the machine with fuel in the fuel tank ■ Never direct a water stream toward people or pets, inside a building where ignition sources are present, or any electrical device. such as hot water and space heaters, clothes dryers, ■... -
Page 9: Product Specifications
Waste electrical products should not be SYMBOLS disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling Safety alert advice. The following signal words and meanings are intended to explain the levels of risk associated with this product. Please read the instructions carefully before starting the machine. -
Page 10: Intended Use
FUEL TANK Engine specifications This fuel tank has a maximum capacity of 1.2l (0.32 US Engine manufacturer Subaru gal). Use unleaded automotive fuel in the engine. Engine model EA190VP0037 FUEL VALVE Engine type 4-stroke Air- cooled The fuel valve must be open to start the engine and should always be closed before storing the machine. - Page 11 WARNING WARNING Do not use this product if any parts on the Packing To prevent accidental starting that could cause serious List are already assembled to your product when you personal injury, always disconnect the engine spark unpack it. Parts on this list are not assembled to the plug wire from the spark plug when assembling parts.
-
Page 12: Operation
connector on the end of the trigger handle. OPERATION ■ Turn the connector clockwise until it stops. This secures the spray wand in place. WARNING CONNECTING HIGH PRESSURE HOSE TO TRIGGER Do not allow familiarity with this product to make you HANDLE careless. -
Page 13: Oxygenated Fuels
■ Replace the lubricant cap / dipstick and securely CAUTION tighten. Do not run the pressure washer pump without water NOTE: This engine has a total lubricant capacity of 0.6l supply connected and turned on, as this may damage (20 oz). the high pressure seals and decrease pump life. - Page 14 up on the lock out until it clicks into the slot. WARNING ■ Remove the nozzle by placing hand over nozzle then While operating and storing, keep at least 1m (3 feet) pulling back the quick-connect collar. of clearance on all sides of this product, including overhead.
-
Page 15: General Maintenance
WASHING WITH DETERGENT ■ When using these settings, test a small area first to avoid surface damage. See figures 16 - 17. ■ Start at the top of the area to be rinsed and work down, As sold, this unit is designed for use with “downstream” overlapping the strokes. -
Page 16: Nozzle Maintenance
the cover. Installing the filter incorrectly will allow dirt to WARNING enter the engine, causing rapid engine wear. Do not at any time let brake fluids, gasoline, ■ Reinstall the air filter cover. petroleumbased products, penetrating lubricants, etc., come in contact with plastic parts. Chemicals can CHECKING SPARK PLUG damage, weaken or destroy plastic which may result in See figure 21. -
Page 17: Preparing For Use After Storage
NOTE: Use of a fuel stabilizer and pump saver will give you better performance and increase the life of the machine. Discharge fuel: Drain the fuel tank completely. Stored fuel can go stale in 30 days. Engine lubricant: Drain the lubricant and replace with fresh, clean lubricant. Spark plug: ■... -
Page 18: Periodic Maintenance Schedule
PERIODIC MAINTENANCE SCHEDULE Maintenance Items Each use 20 hours 50 hours Check for leakage and loose parts Check and refill engine lubricant Change engine lubricant * Clean spark plug Clean air cleaner Replace air cleaner element Clean fuel cap Clean and adjust spark plug and electrodes Replace spark plug Remove carbon from cylinder head ** Check and adjust valve clearance **... -
Page 19: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE POSSIBLE SOLUTION No fuel in tank Fill tank Spark plug shorted or fouled Replace spark plug Spark plug is broken (cracked porcelain Replace spark plug Engine fails to start or electrodes broken) Ignition lead wire shorted, broken, or Replace lead wire or attach to spark disconnected from spark plug plug... - Page 20 Techtronic Industries (Australia) Pty. Ltd. Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia Techtronic Industries New Zealand Ltd. 18-26 Amelia Earhart Avenue Mangere, Auckland 2022, New Zealand 960478025-01...