Subscribe to Our Youtube Channel
Summary of Contents for be3D DeeGreen
- Page 1 Installation and service instructions, warranty terms & conditions DeeGreen User Guide Version 2.4...
- Page 2 DeeGreen User Guide - 2 -...
-
Page 3: Table Of Contents
DeeGreen User Guide Contents 1. Contents ........................- 3 - 2. Technical parameters ..................... - 4 - 3. Safety instructions ....................- 4 - 4. Package contents ....................- 6 - 5. Parts description ..................... - 7 - 6. Getting the printer ready for operation ............. - 9 - 7. -
Page 4: Technical Parameters
Warranty void if damaged due to not following the instructions in this User Guide None of the printer components or accessories are suitable for eating. Avoid eating anything delivered from be3D. Spatula, which is part of the accessory box, is sharp. Beware of cuts. - Page 5 DeeGreen User Guide 11. The printer is a heavy device. In order to avoid injury, or damage to the printer, do not let it fall. 12. Disposal of the device must be performed in accordance with correct environmental directions. 13. Keep the printer away from any flammable substances.
-
Page 6: Package Contents
In order to avoid interruption of the print task due to an ESD event, the DeeGreen M3D0100 3D printer should not be touched during the printing process. If an ESD occurs, the printer will restart. After this situation, it is recommended to use the "parking position"... -
Page 7: Parts Description
DeeGreen User Guide Parts description - 7 -... - Page 8 DeeGreen User Guide Print bed - 8 -...
-
Page 9: Getting The Printer Ready For Operation
DeeGreen User Guide Getting the printer ready for operation Unboxing 1. Make sure the printer is standing on a solid platform and is not upside down. 2. Stand the printer so the protective foam can be accessed. Remove the protection. - Page 10 DeeGreen User Guide Hang the spool on the spool holder. Do not let go of the end of the string freed. Now, follow the Filament installation chapter Filament installation Push the string end through the small box on the back of the spool chamber, until it cannot go any further.
-
Page 11: Printer Menu Scheme
Filaments and selected spare parts can be ordered at your supplier or via distributors of be3D printers. Warranty terms and conditions DeeGreen 3D printer warranty Defect product liability law The law is in accordance with the latest Czech laws regarding product defect responsibility. - Page 12 DeeGreen User Guide Terms & conditions: The manufacturer is responsible for both the device and delivered software to operate properly, all in accordance with this User Guide. All malfunctions and flaws caused by the manufacturing process or the assembly are covered by the manufacturer within the limits of the warranty.
-
Page 13: Authorized Servicing
DeeGreen User Guide The warranty is void when the printer’s electronics and control units are damaged due to atmospheric events such as a thunderstorm, a power network surge, pollution and damage of a mechanical, chemical or heat character, as well as repairs, alternations or modifications by an unauthorized service center or user. - Page 14 DeeGreen User Guide Visually check if the string is pulled in and complete the guide until the melted filament is released off the nozzle. Remove the released filament from the print bed and nozzle. Be extra cautious when removing the filament from the extruder as it is hot and may cause...
- Page 15 DeeGreen User Guide Using your finger place new tube to same position as removed old one, then put and screw the new nozzle same way as you removed it. After that setting the offset setting is necessary Offset setting Offset is the distance between the nozzle and the print bed This is what the model should look like when the offset is set correctly.
- Page 16 DeeGreen User Guide to save the value when you are done by clicking the “Save” button. Then run the print. If the print bed hits the nozzle, or if the layer is too thin and wavy, the offset is too low. On the printer display, go to “Settings” →...
-
Page 17: Contact Details
DeeGreen User Guide Contact details Manufacturer: be3D, s.r.o. ID No.: 49356593 VAT No.: CZ49356593 Contact address: Pod Hajkem 406/1a, Prague 8, 180 00, Czech Republic Invoicing address: Pod Hajkem 406/1a, Prague 8, 180 00, Czech Republic Email: info@be3d.cz help@be3d.cz Web: www.be3d.cz Changes and print errors rights are reserved.
Need help?
Do you have a question about the DeeGreen and is the answer not in the manual?
Questions and answers