Do you have a question about the IM2022 and is the answer not in the manual?
Questions and answers
Joan Harkness
February 20, 2025
Where is the fuse located?
1 comments:
Mr. Anderson
May 14, 2025
The location of the fuse in the Salton IM2022 is not specified in the provided context.
This answer is automatically generated
Steve
January 25, 2025
Red light on and ice maker won’t make ice
1 comments:
Mr. Anderson
February 10, 2025
The red light on the Salton IM2022 ice maker may be on because the Ice Basket is full. In this case, gently remove ice from the Ice Basket using the Ice Scoop. If the ice-making cycle is running but no ice is being made, it could indicate a refrigerant leak or a blocked cooling system pipe, which requires inspection by a qualified technician. Additionally, if the Ice Shovel is jammed due to overflowing ice, allow the ice to melt and restart the ice maker. If water is not filling the Water Tray, clean the Water Filter inside the Water Inlet Tube.
All servicing should be performed by an authorized service representative. See Warranty section. 8. The use of accessories or attachments not recommended by Salton may cause hazards. 9. Do not use outdoors.
18. WARNING: Do not touch the Evaporator when the Ice Maker is making ice, it may burn your skin. SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY GROUNDED PLUG To reduce the risk of electric shock this appliance has a grounded plug. (2 blades and 1 pin) If the plug does not fit fully into the electrical outlet contact a qualified electrician.
BEFORE FIRST USE 1. Remove all packaging and tape. Make sure that you have the Ice Basket, Ice Scoop and extra Silcone Stopper before discarding packaging. 2. Place the Ice Maker on a solid level surface, away from direct sunlight and other sources of heat, such as a stove, furnace and or radiators.
HOW TO USE 1. Open the Drain Plug, on the left side of the unit, and ensure that the Silicone Stopper is installed. Close the Drain Plug. 2. Plug the Ice Maker into the wall outlet and the green power indicator light will blink (approximately every 5 seconds).
HELPFUL HINTS 1. To ensure the cleanliness of the ice cubes, water in the Water Reservoir should be replaced every 24 hours. 2. If the compressor stops for any reason such as water shortage, too much ice, power outage, etc., wait 3 minutes before restarting. 3.
TROUBLESHOOTING GUIDE PROBLEM SOLUTION ‘Add Water’ LED light is on - Lack of water. Press the Power Button to stop the unit. Fill up with water then wait 3 minutes before restarting. - If there is sufficient water, try cleaning the Water Filter (see the Care and Cleaning section) ‘Ice’...
If you are unable to have a defective product replaced under warranty by the retailer, please check our website at “www.salton.com” for the service centre nearest you. You may also contact us for assistance by mail, e-mail, fax or telephone as listed below.
Need help?
Do you have a question about the IM2022 and is the answer not in the manual?
Questions and answers
Where is the fuse located?
The location of the fuse in the Salton IM2022 is not specified in the provided context.
This answer is automatically generated
Red light on and ice maker won’t make ice
The red light on the Salton IM2022 ice maker may be on because the Ice Basket is full. In this case, gently remove ice from the Ice Basket using the Ice Scoop. If the ice-making cycle is running but no ice is being made, it could indicate a refrigerant leak or a blocked cooling system pipe, which requires inspection by a qualified technician. Additionally, if the Ice Shovel is jammed due to overflowing ice, allow the ice to melt and restart the ice maker. If water is not filling the Water Tray, clean the Water Filter inside the Water Inlet Tube.
This answer is automatically generated