ProVisual BA401-SP Instruction Manual

Plug Producing Methods
Instruments needed: wire crimper, network cable tester.
1. R emove 2cm of the insulating layer from the end of cable, and bar together the 4
连 接 接 口
pairs of UTP cables.
Plug Producing Method
2. S eparate the 4 pairs of UTP cable and straighten them.
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should
3. Line up the 8 cables of EIA/TIA 568A or 568B.
conform with EIA/TIA568A or 568B.
1. Please remove 2cm long the insulating layer, and bar the 4 pairs UTP cable;
4. Strip each cable to reveal 1.5cm of bare wire
2. Separate the 4 pairs UTP cable and straighten them;
5. Plug 8 cables into RJ45 plug, making sure that all cables make contact with pins.
3. Line up the 8 pieces of cables per EIA/TIA 568A or 568B.
4. Cut off the cables to leave 1.5cm bare wire;
6. Use a wire crimper to crimp the connection.
5. Plug 8 cables into RJ45 plug, make sure each cable is in each pin.
7. Repeat steps 1-6 to create connections as needed.
6. Use the wire crimper to crimp it;
8. Use a network cable tester to assure cable is working properly before installation.
7. Repeat above 5 steps to make the another end;
8. Using network tester to test the cable whether is working.
pin color
1 white/green
2
green
3
white/orange
4
blue
5
white/blue
6 orange
7 white/brown
8 brown
EIA/TIA 568A
Notice
When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
HIGH RISK OF ELECTROCUTION.
There are uninsulated and dangerous voltages within the enclosure of this
lso please make
product. These currents may be of sufficient magnitude to cause electric shock
or death to individuals.
To reduce the risk of electric shock, please do not remove the cover or back of
this product. Only a qualified technician should tamper with the interiors of this
item and it's electrical components.
To prevent fire or shock hazards, do not expose unit
to water for an extended period of time.
• Avoid using this product at extreme high or low temperatures.
For more information please review product specifications.
• Never expose products to direct sunlight or other extreme
conditions, damages to your product could occur.
• Do not mount or place any products near a heater or radiator.
4
*Violation of any of these recommendations could result in ProVisual voiding this products warranty. Please
visit our website for all details regarding your warranty.
POE Injector
pin color
1
white/orange
2
orange
3 white/green
4 blue
5
white/blue
6
green
7
white/brown
8 brown
EIA/TIA 568B
CAUTION:
BA401-SP
Congratulations on purchasing this BA401-SP model PoE splitter. This item is
compatible will all PoE switches that are based on IEEE 802.3af standards. This
splitter can also provide data and a power source for devices that do not support
PoE Splitter
PoE functions. The BA401-SP provides 3 levels of power output, DC 5V / 12V / 24V
providing different power requests for IP devices.
The product is a PoE Network and Power Splitter based on
compatible with POE switch that based on IEEE 802.3af standard. The product can also
NOTE: Please read this instructional booklet carefully to ensure proper use of the
provide network and power source for network device that does not support PoE function.The
product, as well as reduce the risk of injury or death.
product provide DC 5V/12V/24V 3 Level Power output. It can support different power request
for IP camera or IP device.。
Application
IP Camera
Feature
Voltage Output:
Product Features
product. Support 10/100/1000 Mbps data conversion.
Power Output：≤15.4W;
Transmission Medium：Cat5/5e/
• Voltage Output: DC5V/12V/24V, 10/100/1000 Mbps data conversion
Standard: Support IEEE802.3af Standard; Power supply support A（End-Span）and
• Power Output: ≤ 15.4W
mode B（Mid-Span）
• Standard: Supports IEEE802.3af, Power supply support A (end-span)
Protection: Excellent circuit protection, strong lighting protection and anti-interference.
and mode B (mid-span).
Notice
4
• Protection: Excellent circuit, lighting and anti-interference protection.
To make sure the transmission quality, please use standard Cat5/5e/6 cable.
• Structure: Supports tablet installation. 2 sets of PoE power adapters
1
can be connected with a Bayonet.
| PoE Splitter Instruction Manual
IEEE 802.3af
IP Dome Camera
IP Camera
IP PTZ Camera
DC5V/12V/24V DIP Adjustment Available, available for various ethernet
6 Cable;
；
Board
Front
. The device is
Back
M
o n
i t o
r
Insta
Please c
dealer.
POE S
M to M
User M
Please
1) Please
2) Conne
port;
3) Conne
4) Conne
5) Please
1