Advertisement
Quick Links
a
Capacities
Steel
Wood
I
Wood screw
I
Machine screw
Cordless Driver Drill
No load speed
Dimensions
Net
(L x W x H)
weight
(RPM)
Equipped with Electric Brake
MODEL 6222DE
MODEL 6222DWE
Battery Cartridge 9120
INSTRUCTION MANUAL
*
Model DC9700 Fast Charger
With Fast Charger
9.6 V
SPEC IF I CAT1 0 N S
A.C. only 50 Hz
-
60
Hz
D.C. 7.2 V, 9.6 V
1 Hr.
*
Model 6222D
I
I
I
10
mm
15
mm
5.1 mm x 35
mm
202
mm
x 77
mm
x
221
mm
1.4 kg
(318")
I
(518")
I
(3116'' x 1.318")
I
I
13.1 lbsl
"
(114"1
1
-
700
I
(7-15116" x 3" x 8-314")
Voltage
I
Input
I
output
I
Charging time
Advertisement
Related Manuals for Makita CORDLESS DRIVER DRILL 6222DE
Summary of Contents for Makita CORDLESS DRIVER DRILL 6222DE
- Page 1 Cordless Driver Drill INSTRUCTION MANUAL SPEC IF I CAT1 0 N S Model 6222D Capacities Steel Wood Wood screw 5.1 mm x 35 (318") (518") (3116'' x 1.318") Battery Cartridge 9120 Model DC9700 Fast Charger Voltage 9.6 V A.C. only 50 Hz Equipped with Electric Brake No load speed (RPM)
-
Page 2: Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user the tool.
- Page 5 Before using battery charger, read all instructions and cautionary markings battery charger, 12) battery, and CAUTION To reduce risk of injury, charge only MAKITA Battery Cartridge 9100. Other types of batteries may burst causing personal injury and damage. Do not expose charger t o rain or snow.
- Page 6 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle.
- Page 7 Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and Always insert it all the way until it locks in...
-
Page 8: Operation
ASSEMBLY Installing or removing driver bit or drill bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit Hold the ring and turn the sleeve counter- clockwise to open the chuck jaws. Place the bit in the chuck as far as the ring firmly and turn the sleeve clock- wise to tighten the chuck. - Page 9 CAUTION: Always withdraw the tool from the workpiece before resuming operation. If the tool can- not be withdrawn, hold the tool firmly when turning on the tool, reaction. Adjusting the fastening torque The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body.
- Page 10 Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the ing. Then proceed as follows. *Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw.
-
Page 11: Maintenance
Always be sure that the tool is switched off and the battery cartridge before attempting t o perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Recycling the Battery... - Page 12 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified manual. The use any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments Bits Size Phillips Slotted...
- Page 13 1 Hour Automotive charger Model DC9112 Part No. 1131 1 0 - 5 1 Hour charger Model DC1201 Part No. 113126-0 Battery cartridge 9120 Part No. 192638-6 Plastic carrying case Part No. 824447-2 High Capacity charger Model DC1410 1 Hour Automotive charger Model DC1412 Battery cover Part No.
- Page 14 F e b . - l l - ' 9 7 CORDLESS DRIVER DRILL Model 6222D Note: The switch and other part configurations may differ from country to country.
- Page 15 Spur Gear 15 Spur Gear 15 Spur Gear Complete Spur Gear 15 Spur Gear 15 Spur Gear Internal Gear 42 Flat Washer 12 Motor 9 6 Hand Strap Battery 9120 Handle Set IWith Item 11 Steel Ball Makita Label Feb-11-'97...
- Page 16 MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.