1. Manuals
  2. Brands
  3. Axmin Manuals
  4. Saw
  5. UE-153DV1
  6. Operation manual

Axmin UE-153DV1 Operation Manual

Small band saw machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UE-153DV1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Axmin UE-153DV1

  • Page 2: Table Of Contents

    Table of Contents General Safety Rules ......................1 Electrical schematic ......................... 2 Before cutting ........................... 3 Pump grease ........................... 3 The Quick Vise and Work Set Up ..................3 Usage of the vise ........................3 Work set up ..........................3 Special Safety Rules for Metal Saw ..................

  • Page 3: General Safety Rules

    1. General Safety Rules WARNING Read and understand instructions of this manual entirely before operating the machine. Always wear approved safely glasses /face shields when using the machine. Make certain the machine is properly grounded. Before machine in operation, remove tie, ring, watch, other jewelry, and roll your sleeves up to above elbows.

  • Page 4: Electrical Schematic

    Electrical Schematic - 2 -...

  • Page 5: Before Cutting

    Before Cutting 2. The Quick Vise and Work Set Usage of the Vise The vise is mounted on the machine base. Follow the easy steps to open or close the vise. Fig. 1 Release the lock pin (A) in Fig.1 to free this saw. After service, must relock in the pin to the saw Fig.

  • Page 6: Special Safety Rules For Metal Saw

    3. Special Safety Rules for Metal is equipped with a bi-metallic blade which can be used to cut stainless steel, steel, iron, brass, aluminum, wood, plastic and so ˙ Make sure the direction of rotation WARNING: For your own safety, do not arrow on the blade matches the operate your metal saw until it is direction arrow on the saw.

  • Page 7: Whenever Saw Is Running

    After finishing a cut, keep holding the power ˙ Tie back long hair. head down, release the switch, and wait for ˙ Roll long sleeves above the elbow. all moving parts to stop before moving your To avoid injury from accidental starting, hands.

  • Page 8: Earth

    Earth handle normal loads. For heavy loads, however, the voltage (caused by a small size wire in the supply circuit or This metal saw is single insulated tool, so the an overly long supply circuit wire) may earth system is provided to protect you from drop too low for the motor to operate.

  • Page 9: Description And Characteristics

    WARNING SHUT OFF THE POWER SOURCE ALL THE TIME, BEFORE THIS MACHINE IS IN MAINTENANCE, OPERATION, ADJUSTMENT, OR REPAIRMENT. Fig. 4 WARNING Disconnect machine from the power source! Item Attached Parts Q’ty No matter when, where, or how. Pay extra attention to the saw during it in transportation, Stop Rod Assembly (E) 1 set...

  • Page 10: Auto Cutting

    Auto Cutting Trigger switch Feed Rate by spring holding Turn toggle switch to lower location. (Fig. 7) Select spring as outer location. (Lower photo Fig.8) Press green button down (Fig. 5) to start auto cutting. Fig. 9 Toggle switch Angle Cutting The machine uses a swivel miter base for angle cutting from 0~60 degree.

  • Page 11: Changing Blade

    Changing Blade Raise this saw head up-to proper position by lifting up the arm Fig.11. Fig. 14 Remove blade from both wheels and blade guides bearings in Fig.15. Fig. 11 Remove the blade guard by loosening two screws (U) in Fig. 12 on the saw frame. Blade guides bearings Fig.

  • Page 12: Magnetic Switch

    Magnetic Switch Adjusting Poor Cutting The band saw is equipped with magnetic switch The machine has been adjusted and in Fig.16, which is designed for operating safety. power-tested with several test cuts before After power failure, the machine has to be leaving the factory to insure proper cutting.

  • Page 13: Changing The Motor Carbons Brushes

    Changing the Motor Carbons There are coppers sheet with wiring covered on the carbon brushes (Fig.22). Brushes If the motor is making an unusual noise then the carbon brushes may need to be replaced. Disconnect machine from power supply. Remove two tap screws connected with on/off switch’s box, and three Phillips head screws around cover base.

  • Page 14: Part List & Explosion Drawings

    PARTS LIST Part No. Description Size No. Q'ty Part No. Description Size No. Q'ty Round head nut Locking handle 3/8" Handle rod Hook screw 3/8x1-3/4" Lead screw base Hex. soc. cap screw M5x12 Lead screw Position plate Spacer M10x17 Table Adjusting hook Vise table Tension spring...
  • Page 15 PARTS LIST Part No. Description Size No. Q'ty Part No. Description Size No. Q'ty Center gear M10x17x8 4x4x6 Side bracket 1m/m Center gear shaft Hex. cap bolt M8x13x16 Speed meter Flat washer M8x19x1.5 Motor base 1/2" 93-1 Hex. soc. cap screw M5x25 Adjusting bolt Motor...
  • Page 16 - 14 -...
  • Page 17 - 15 -...
  • Page 18 - 16 -...

Table of Contents