Table of Contents
Advertisement
Available languages
Available languages
Quick Links
COMMERCIAL
CEILING FANS
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer at the address or
telephone number listed in the warranty.
2. Before servicing or cleaning unit, or installing a light kit, switch power
off at service panel and lock service panel to prevent power from
being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
5. This unit must be grounded.
6. Do not use this fan with any solid-state fan speed control device.
7. Most outlet boxes commonly used for the support of lighting fixtures
are not acceptable for fan support and may need to be replaced,
consult a qualified electrician if in doubt.
Use only UL Listed outlet boxes marked "FOR FAN SUPPORT".
The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 50 pounds. Use only
the two steel screws (and lock washers) provided with the outlet box
for mounting the ceiling fan to the outlet box The outlet box must
not twist or work loose. DO NOT USE PLASTIC OUTLET BOXES.
8. After marking electrical connections, spliced conductors should
be turned upward and pushed carefully up into outlet box. The
wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box.
9. After installation is complete, make sure that all connections are
secure to prevent the fan from falling. Make sure all wire connections
are secure, and that there are no exposed conductor strands.
10. Do not use water or detergents when cleaning the fan or fan blades.
A dry dust cloth or lightly dampened cloth will be suitable for most
cleaning.
MODELS CFC56BR • CFC56WH
CAUTION
TO REDUCE THE RISK OF PERSONAL INJURY, OBSERVE THE
FOLLOWING:
1. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power unit.
2. The fan must be mounted with a minimum of 10 feet clearance
between fan blades and floor.
3. Make sure that your installation will not allow the fan to come into
contact with any adjacent obstacles such as doors, hanging lamps,
etc.
4. If you are installing more than one ceiling fan, do not mix the blade
sets.
5. Do not bend the blade brackets.
6. Do not insert objects in between rotating fan blades.
7. Be careful when working around or cleaning the fan.
8. Please read specification label on product for further information
and requirements.
WEIGHT OF FAN
The weight of your fan is 17.9 lbs. The weights of light kits, down rods,
and ceiling adapters are listed in the instructions packed with those
accessories.
INSTALLER:
Leave this manual with the
homeowner.
HOMEOWNER:
Use and care instructions on
page 6.
Page 1
Advertisement
Table of Contents
Related Manuals for NuTone CFC56BR
Summary of Contents for NuTone CFC56BR
- Page 1 MODELS CFC56BR • CFC56WH Page 1 COMMERCIAL CEILING FANS READ AND SAVE THESE INSTRUCTIONS WARNING CAUTION TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO REDUCE THE RISK OF PERSONAL INJURY, OBSERVE THE TO PERSONS, OBSERVE THE FOLLOWING: FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If...
-
Page 2: Mounting Options
MODELS CFC56BR • CFC56WH Page 2 CONTENTS Unpack your fan and check the contents. You should have the following items: A - Blade Set (3) B - Hanger Bracket Assembly C - 6” Downrod D - Coupling Cover E - Fan Motor Assembly F - Package Hardware: Mounting Hardware 2 screws, 2 wood screws, 2 washers, 4 lock washers, OUTLET BOX 3 wire nuts Balance Kit FIGURE 1 TOOLS & MATERIALS REQUIRED FLAT... -
Page 3: Install The Fan
MODELS CFC56BR • CFC56WH Page 3 INSTALL THE FAN CEILING HANGER 1. Remove the decorative canopy bottom cover from the canopy by BRACKET turning the cover counter clockwise. (Fig. 5) CEILING 2. Remove the hanger bracket from the canopy by removing the 1 of CANOPY 2 screws from the bottom of the hanger bracket and loosening the other one a half turn from the screw head. Next, turn the canopy counter clockwise to removing the hanger bracket from the canopy. (Figure 5) CANOPY COVER 3. Pass the 120-volt supply wires through the center hole in the ceiling FIGURE 5 hanger bracket as shown in Fig. 6. CUL LISTED 4. Secure the hanger bracket to the ceiling outlet box with the screws ELECTRIAL and washers provided with your outlet box. 5. Remove the hanger pin, locking pin and set screws from the top of the motor assembly. WASHERS... -
Page 4: Connect Wiring
MODELS CFC56BR • CFC56WH Page 4 INSTALL SAFETY SUPPORT 1. An additional safety support is provided to prevent the fan from falling. Secure the safety cable to the ceiling joist with screw and washer, as illustrated in Figure 9. HANGER SAFETY CABLE BRACKET FIGURE 9 CONNECT WIRING Remember to disconnect the power. Follow the steps below to connect 120 VAC the fan to your building/facility wiring. Use the wire nuts supplied with LINE IN your fan. Secure the connectors with electrical tape. Make sure there GREEN are no loose strands or connections. -
Page 5: Finish Installation
MODELS CFC56BR • CFC56WH Page 5 FINISH INSTALLATION 1. Tuck connections neatly into ceiling outlet box. OUTLET 2. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 13) HANGER BRACKET 3. Align the circular hole on canopy with the remaining hole on the SCREWS mounting bracket, secure by tightening the two set screws. Note: Adjust the canopy screws as necessary until the canopy and canopy cover are snug. CANOPY Warning: Make sure tab at bottom of hanger bracket is properly seated in groove of hanger ball before attaching canopy to bracket. -
Page 6: Operation
MODELS CFC56BR • CFC56WH Page 6 OPERATION TROUBLESHOOTING Fan will not start. Turn on the power and check the operation of your fan. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. WALL SWITCH (OPTIONAL) Fan sounds noisy. Your fan is also designed to operate with a wall switch (sold separately). 1. Make sure all motor housing screws are snug. Refer to wall switch instructions for installation and wiring information. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing. CAUTION: Make sure main power is off. MAINTENANCE 4. Allow a 24-hour “breaking-in” period. Most noise associated with a new fan disappear during this time. 5. Some fan motors are sensitive to signals from solid-state variable IMPORTANT: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL speed controls. If you have installed this type of control, choose and... -
Page 7: Service Parts
MODELS CFC56BR • CFC56WH Page 7 SERVICE PARTS K EY PART NO. DESCRIPTION 1 S77000972 BLADE SET (CONTAINS 3) (CFC52WH) S77000973 BLADE SET (CONTAINS 3) (CFC52BR) 2 S77000974 CANOPY (CFC52WH) S77000975 CANOPY (CFC52BR) 3 S77000979 DOWNROD W/BALL, 6” (CFC52WH) S77000980 DOWNROD W/BALL, 6” (CFC52BR) 4 S77000976 COUPLING COVER (CFC52WH) S77000977 COUPLING COVER (CFC52BR) -
Page 8: Warranty
Any assistance NuTone provides to or procures for you outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty. NuTone will not reimburse you for any expenses incurred by you in repairing or replacing any defective Fan, except for those incurred with NuTone’s prior written permission. HOW TO OBTAIN WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address or telephone number stated below within seven (7) days of discovering the covered defect, (b) give the model number and part identification and (c) describe the nature of any defect in the fan or part. At the time of requesting warranty service, you must present evidence of the original purchase date. Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (888-336-6151) If you must send the fan or part to NuTone, as instructed by NuTone, you must properly pack the fan or part—NuTone is not responsible for damage in transit. 79040061A... - Page 9 MODELOS CFC56BR • CFC56WH Página 9 VENTILADORES DE TECHO COMERCIALES LEA Y GUARDE ESTAS INSTRUCCIONES ADVERTENCIA PRECAUCIÓN PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA PARA REDUCIR EL RIESGO DE LESIONES, SIGA LAS INDICACIONES O LESIONES, SIGA LAS INDICACIONES QUE SE ENUMERAN A QUE SE ENUMERAN A CONTINUACIÓN:...
-
Page 10: Herramientas Ymateriales Requeridos
MODELOS CFC56BR • CFC56WH Página 10 CONTENIDO Desempaque su ventilador y verifique que el contenido esté completo. El paquete debe incluir lo siguiente: A - Juego de paletas de doble faz (5) B - Conjunto de soportes de suspensión C - Barra descendente D - Tapa acopladora E - Conjunto del motor del ventilador F - Paquete del equipo: Herrajes de montaje CAJA DE DISTRIBUCIÓN 2 tornillos, 2 tornillos para madera, 2 arandelas, 4 arandelas de seguridad, 3 tuercas para alambre Kit de nivelación FIGURA 1 HERRAMIENTAS Y MATERIALES REQUERIDOS CAJA DE DISTRIBUCIÓN... - Page 11 MODELOS CFC56BR • CFC56WH Página 11 INSTALACIÓN DEL VENTILADOR SOPORTE DE SUSPENSIÓN PARA TECHO 1. Retire la tapa inferior de la carcasa decorativa girando la cubierta en CARCASA sentido contrario a las agujas del reloj. (Fig. 5) PARA TECHO 2. Quite el soporte de suspensión de la carcasa, retire 1 de los 2 tornillos de la parte inferior del soporte de suspensión y afloje el segundo girando media vuelta la cabeza del tornillo. A continuación, gire la carcasa TAPA DE LA en sentido contrario a las agujas del reloj para retirar el soporte de CARCASA FIGURA 5 suspensión. (Figura 5)
- Page 12 MODELOS CFC56BR • CFC56WH Página 12 INSTALACIÓN DEL SOPORTE DE SEGURIDAD 1. Se incluye un soporte de seguridad adicional para evitar que el ventilador se caiga. Sujete el cable de seguridad a la viga del techo SOPORTE DE con un tornillo y una arandela, tal como se muestra en la figura 9. CABLE DE SUSPENSIÓN SEGURIDAD FIGURA 9 CABLEADO DE CONEXIÓN Recuerde desconectar la alimentación eléctrica. Siga los pasos que se ENTRADA DE indican a continuación para conectar el ventilador a la instalación eléctrica...
-
Page 13: Terminación De La Instalación
MODELOS CFC56BR • CFC56WH Página 13 TERMINACIÓN DE LA INSTALACIÓN 1. Introduzca las conexiones de forma ordenada en la caja de distribución del techo. CAJA DE DISTRIBUCIÓN 2. Deslice hacia arriba la carcasa al soporte de manera que el orificio de la carcasa quede sobre el tornillo del soporte de montaje. A continuación, SOPORTE DE gire la carcasa hasta que quede trabada en su lugar en la sección más SUSPENSIÓN angosta de los orificios. (Fig. 13) TORNILLOS 3. Alinee el orificio circular de la carcasa con el orificio restante del soporte, asegúrelos apretando los dos tornillos de sujeción. CARCASA Nota: Ajuste los tornillos de la carcasa según sea necesario hasta que la carcasa y su cubierta queden bien ajustadas. Advertencia: Antes de sujetar la carcasa al soporte, asegúrese de que la lengüeta en la parte inferior del soporte de suspensión calce bien en... -
Page 14: Solución De Problemas
MODELOS CFC56BR • CFC56WH Página 14 FUNCIONAMIENTO SOLUCIÓN DE PROBLEMAS El ventilador no se enciende. Encienda la alimentación y verifique el funcionamiento de su ventilador. 1. Verifique los fusibles o los disyuntores. 2. Verifique las conexiones de los cables al ventilador y las conexiones del cable del interruptor en la carcasa de interruptores. PRECAUCIÓN: INTERRUPTOR DE PARED (OPCIONAL) Asegúrese de que el interruptor principal de alimentación esté apagado. Su ventilador también está diseñado para funcionar con un interruptor de pared (vendido por separado). Consulte las instrucciones del interruptor de El ventilador hace mucho ruido. pared para su instalación y la información de cableado. 1. Asegúrese de que todos los tornillos de la carcasa del motor estén bien ajustados. 2. Asegúrese de que los tornillos que sujetan los soportes de las paletas al cubo del motor estén bien ajustados. -
Page 15: Piezas De Servicio
MODELOS CFC56BR • CFC56WH Página 15 PIEZAS DE SERVICIO CLAVE Nº DE PIEZA DESCRIPCIÓN 1 S77000972 JUEGO DE PALETAS (INCLUYE 3) (CFC52WH) S77000973 JUEGO DE PALETAS (INCLUYE 3) (CFC52BR) 2 S77000974 CARCASA (CFC52WH) S77000975 CARCASA (CFC52BR) 3 S77000979 BARRA DESCENDENTE CON BOLA DE 6” (CFC52WH) S77000980 BARRA DESCENDENTE CON BOLA DE 6” (CFC52BR) 4 S77000976 CUBIERTA DE ACOPLAMIENTO (CFC52WH) S77000977 CUBIERTA DE ACOPLAMIENTO (CFC52BR) 6 S77000978 BOLSA DE PIEZAS * S77000981 SOPORTE DE MONTAJE... - Page 16 LIMITADAS, LA DURACIÓN DE CUALQUIER GARANTÍA IMPLÍCITA APLICABLE ESTÁ LIMITADA AL PERIODO ESPECIFICADO PARA LA GARANTÍA EXPRESA. Algunos estados no permiten limitaciones en la duración de una garantía implícita, así que la limitación anterior tal vez no aplique en su caso. Cualquier descripción verbal o escrita del ventilador es para el único propósito de identificarlo y no deberá considerarse como una garantía expresa. REMEDIO: Durante el periodo de garantía limitada aplicable, NuTone, a su opción, suministrará piezas de repuesto, o reparará o reemplazará, sin cargo alguno, cualquier ventilador o pieza, hasta el grado en que NuTone lo encuentre cubierto bajo esta garantía limitada y en incumplimiento de la misma. NuTone le enviará el ventilador reparado o reemplazado o las piezas de repuesto sin cargo. Usted es responsable de todos los costos de retiro, reinstalación y envío, seguro u otros cargos de flete incurridos en el envío del ventilador o la pieza a NuTone.