Table of Contents
Advertisement
Quick Links
User Manual v1.0
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
•
GSM communicator ET07 (further referenced as system) contains a radio transceiver operating in GSM900 and GSM1800 bands.
•
Don't use the system where it can interfere with other devices and cause any potential danger.
•
Don't use the system with medical devices if this is required in the manual of the medical device.
•
Don't use the system in hazardous environment.
•
Don't expose the system to high humidity, chemical environment or mechanical impacts.
•
Don't attempt to personally repair the system.
•
System labelling sticker is at the bottom of the device.
System ET07 is a device mounted in limited access areas. Any system repairs must be done only by qualified, safety aware
personnel.
Mains power must be disconnected before any installation or tuning work starts. The system installation or maintenance
must not be done during stormy conditions.
The system must be powered by main 11-24V 50Hz ~300mA AC or 11-24V --- 300mA DC power supply which must be appro-
ved by LST EN 60950-1 standard and be easily accessible.
Any additional devices linked to the system ET07 (computer, alarm control panel etc.) must be approved by LST EN 60950-1
standard.
External power supply can be connected to AC mains only inside
installation room with automatic 2-pole circuit breaker capable of
disconnecting circuit in the event of short circuit or over-current con-
dition. Open circuit breaker must have a gap between connections of
more than 3mm.
Fuse F1 type 5x20 mm 3A Slow blown. Blown fuse cannot be replaced by the user and the replacement fuses have to be
exactly the same as indicated by the manufacturer.
The device is fully turned off by disconnecting 2-pole switch off device of the external power supply or any other linked
device that the system ET07 is powered from.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that in the EU
the product must not be disposed of together with household waste.
Copyright © "ELDES UAB", 2009. All rights reserved.
It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from "ELDES
UAB". "ELDES UAB" reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB declares that this
COMMUNICATOR ET07 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of confor-
mity may be consulted at www.eldes.lt/ce.
Phase
Null
Grounding
AC 230V
50 Hz/DC 24V
ET07
USB cable
Advertisement
Table of Contents
Summary of Contents for Eldes ET07
-
Page 1: Safety Instructions
Copyright © “ELDES UAB”, 2009. All rights reserved. It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB declares that this COMMUNICATOR ET07 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. -
Page 2: Table Of Contents
3. GSM antenna ............1 pcs About User Manual. Quick Start. This document describes remote informing system ET07, its operation and installation. It is very important to read User Manual before start using the system. A quick start guide is located in first two chapters. -
Page 3: General Information
1. General Information 1.1 Function Communicator ET07 is for transferring information from the Alarm Control Panel to the monitoring station via GSM audio con- nection channel or/and users via SMS message. The system van be used in the following applications: •... -
Page 4: Connection Circuit
Connectors for restoring factory default settings RS232 COM port connection Mini USB port Connectors for enabling the 3 operation mode of the device MODE Connectors for connecting the 2 operation mode of the device PROG Not used USER MANUAL ELDES ET07 V1.0... -
Page 5: System Installation
1.6 System Installation NoTE Due to GSM network characteristics it is recommended to use the system ET07 with the same GSM operator which is used by system users. Thus you will ensure the quickest SMS message delivery and receipt. NoTE To ensure maximum system operation reliability we recommend do not use prepaid cards. -
Page 6: Light Emitting Indicators Functionality
Control Panel to the panel of security service. (this indication is possible then device is working in first mode) Indicator is lit The device decodes the data sent via CONTACT ID protocol to textual, user-understandable information. USER MANUAL ELDES ET07 V1.0... -
Page 7: System Pre-Operation
ET07 Configuration Tool (for more information please refer to user manual of this program). SMS messages can be received by up to 5 users. -
Page 8: Appendix
System configuration is performed by using program software ET07 Configuration Tool that can be downloaded from internet website www.eldes.lt Before connecting the cable to the computer via USB (or RS232 type) port read ET07 Configuration Tool user manual that can be found in HELP section of the program. - Page 9 Pagaminta Lietuvoje. Made in Lithuania. Сделано в литве. www.eldes.lt...