Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Simplicity GKTG6SY2B
- Page 2 Dear customer! This electric integrated gas cooker is manufactured for household use. Our appliances are packed in the environmentally friendly materials which may be recycled, deposited or destroyed without any hazard to the environment. Such packaging materials are also labeled accordingly. Once the life cycle your appliance is over, make sure not to pollute the environment, and deliver it to the authorized collectors of old household appliances.
- Page 3 TECHNICAL INSTRUCTIONS AND INSTALLATION Important warnings • Installation of the appliance into a kitchen worktop and its connection to the power mains and the gas supply may only be performed by an adequately qualified technician. • When the appliance is in use, additional heat and moisture are emitted into the room.
-
Page 4: Installation
• Minimum distance between the built-in cooking hob and the rear wall is indicated on the installation drawing. • Cooking hobs can be installed into worktops that are 25 to 40 mm thick. The front part must have an opening of no less than 5 mm. GKTG6SY2B GKTG6SY2W A (mm) B (mm) -
Page 5: Connecting The Appliance To The Power Mains
Before inserting the appliance into the opening in the kitchen worktop, the supplied Installing the foam foam gasket must be attached to the lower side of the glass ceramic (glass) cooking gasket hob (see fi gure above). Do not install the appliance without the foam gasket! The gasket should be attached to the appliance in the following way: - Remove the protective film from the gasket. - Page 6 other side, adjacent to the appliance. • The current conducting and isolated parts must be protected from any possibility of direct contact. WARNING! • Before any intervention, disconnect the appliance from the power mains. Connect the appliance in compliance with the electric connections diagram supplied; make sure the relevant network voltage is observed! The ground wire (PE) should be connected to the clip indicated by the earthing symbol.
- Page 7 • When connecting, the knee R1/2 should be held firmly to prevent it from rotating. • For sealing of the connection joints, use a non-metal approved gaskets and approved sealants. • The gaskets should only be used once. The thickness of the flat non-metal gaskets should not be deformed more than by 25 percent.
-
Page 8: Technical Information
Tighten the screw on the side of the tap, rod clockwise completely. Warning: these tasks may only be carried out by a qualified technician, authorized by the gas distributing company or authorized service center! TECHNICAL INFORMATION (TABLE 1) GKTG6SY2B GKTG6SY2W Appliance dimension (mm) Operating voltage 220-240 V~, 50/60 Hz... -
Page 9: Appliance Description
burner is insufficient; as a result, combustion effect is lesser. Burner type Pan diameter Auxiliary (1,0 kW) 120 - 180 mm Semirapid (1,75 kW) 180 - 220 mm Mini-Wok (3,3 kW) 220 - 300 mm Important warnings regarding the glass ceramic hob •... - Page 10 Hob control elements for both left cooking zones Cooking time function For both left cooking zones the cooking time can be set. When the countdown cooking time expired the gas on selected burner is turned off. Cooking time can be set from 1 to 99 minutes. Time function settings Turn on the gas cooking zone.
-
Page 11: Cleaning And Maintenance
permanently. • The flame can then be set between the maximum and minimum level. Any setting between 0 and the large flame is not recommended, as the flame is not stable in this interval and may be extinguished. WARNING: once the cook top has been cleaned, ensure that the burners are firmly in their seats and do not interfere with the igniter. - Page 12 Apply sparingly with a soft cloth following the instructions on the packaging. Printed surfaces The printing can be damaged if soiling (e.g. food or fluids that contained salt, olive oil) is not removed immediately. Remove any soiling immediately. Do not use any stainless steel cleaner on printed surfaces. This would rub off the print.
- Page 13 or the stability of the surface. Such discolorations are mostly a result of burnt food residues or use of cookware made of materials such as aluminum or copper; these stains are difficult to remove. Warning: All damage described above predominantly relates to the aesthetics, i.e. appearance of the appliance and do not affect its functionality directly.