Charging the PRYMEBLU Speaker Microphone
The PRYMEBLU Speaker Microphone has an internal Lithium Ion rechargeable battery pack which must
be charged prior to operation, and must be recharged regularly. A fully charged battery will provide
approximately 11 hours (or more) of operation before needing to be recharged. However, operating time
can vary depending on usage and the condition of the battery pack. Recharge the battery regularly.
STEP ONE: Charging the PRYMEBLU Speaker Microphone
To charge the PRYMEBLU Speaker Microphone
1. Ensure the PRYMEBLU Speaker Microphone is turned o using the multifunction button.
2. Plug the supplied wall charger into a standard 120 volt AC outlet.
3. Plug the charge cable into the AC wall charger and then into the charge jack on the bottom of the
PRYMEBLU Speaker Microphone. You will need to remove the protective rubber cover that is inserted
into the charge jack. (To prevent dust and moisture from damaging your speaker microphone, always
ensure this cover is in place when you are not charging the BTH-SPM100.)
4. Once the charging process has begun, the LED indicator on the bottom of the PRYMEBLU Speaker
Microphone will show a constant red light. When the battery is done charging, the LED light will
change to a constant green color.
5. Typical charge time is approximately three hours. Actual charge time will vary depending on several
factors including the battery's charge state, condition, and age.
6. Disconnect the charger from the adapter when charging is completed.
Charging Cautions:
- Use only the wall charger supplied by the manufacturer. Do not use any other charger.
- Do not use a wall charger that appears to be damaged. (Example: frayed wires, melted plastic, etc.)
Contact PRYME to get a new manufacturer-approved replacement charger.
- Do not tamper with or modify the PRYMEBLU Speaker Microphone or charger.
- Always turn PRYMEBLU Speaker Microphone o when charging.
3
Controls and Connection
Front Firing Speaker
Received calls are heard over this speaker.
The volume level is controlled using the
volume control knob on the two-way radio.
PTT Button
When the PRYMEBLU Speaker
Microphone is paired to a PRYMEBLU
Radio Adapter, pressing and holding
this button will cause the two-way
radio to transmit.
Accessory Jack
This jack is used to connect
the supplied wall charger to the
speaker microphone; can also be
used to connect a wired listen-only
earphone for enhanced privacy.
Multifunction Button
Turns the PRYMEBLU Speaker Microphone on and o . Also, this button can be used
to place the PRYMEBLU Speaker Microphone into pairing mode so that it can be
connected wirelessly to a new PRYMEBLU Radio Adapter.
Pairing with a PRYMEBLU Radio Adapter and 2-way Radio
STEP TWO: Pairing with a PRYMEBLU Radio Adapter
When pairing the PRYMEBLU Speaker Microphone with a PRYMEBLU Radio Adapter, make sure
that the speaker microphone, adapter, and the two-way radio the adapter is connected to are
all powered o .
If your PRYMEBLU Radio Adapter gets power directly from the two-way radio it is attached to:
• Hold down the Talk button on the PRYMEBLU Radio Adapter while turning the two-way radio ON.
If your PRYMEBLU Radio Adapter has its own charger/internal battery pack:
• Turn the power switch on the PRYMEBLU Radio Adapter to the ON position while holding down
the multifunction Talk button on the PRYMEBLU Radio Adapter.
If your PRYMEBLU Radio Adapter gets power from an external source (such as an automobile cigarette
lighter jack):
• Hold down the Talk button on the PRYMEBLU Radio Adapter while plugging the adapter into the
external power source (cigarette lighter jack).
Continued on page 5
Microphone:
This microphone picks up the user's
voice audio to send over- the-air
Clothing Clip
The alligator-type clip secures
the PRYMEBLU Speaker Microphone
to the user's clothing during use.
The clip can be rotated to allow the
microphone to be better positioned.
Status LED
The LED ashes messages that
let the user know the current
status of the PRYMEBLU Speaker
Microphone.
2
4