1. Introduction I. Introduction 1.1. Purpose This manual provides the information necessary to repair, calibration, description and download the features of the F9200. 1.2. Regulatory Information 1.2.1. Security Toll fraud, the unauthorized use of telecommunications system by an unauthorized part (for example, persons other than your company’s employees, agents, subcontractors, or person working on your company’s behalf) can result in substantial additional charges you’re your telecommunications services.
Page 5
1. Introduction 1.2.5. Notice of Radiated Emissions The F9200 complies with rules regarding radiation and radio frequency emission as defined by local regulatory agencies. In accordance with these agencies, you may be required to provide information such as the following to the end user. 1.2.6.
2. General Performance 2. General Performance 2.1 Hardware Feature Class GPRS Class 10 Radio Tri Band (GSM900/DCS1800/PCS1900) Camera 1.3M CMOS Display 2.0 176 x 220 262K TFT Connectivity Bluetooth Class1, USB Sound 64 Poly Battery 1000 mAh (min) Li-Ion Size / weight 106 x 46.5 x 16mm , 105g - 7 -...
Page 11
3. Technical Brief BaseBand Components (Sub_Camera) U100 LD100 CN101 CN100 LD100 Camera Flash U100 Hall switch CN100 B to B Conn CN101 Camera Conn - 12 -...
Page 12
3. Technical Brief BaseBand Components (Touch FPCB) CN100 U100 U100 Touch Sensor CN100 B to B conn - 13 -...
3. Technical Brief 3.4 Memory • 256 Mbit Nor flash memory + 128Mbit PSRAM • 16 bit parallel data bus • ADD01 ~ ADD24 • RF Calibration data and battery calibration data are also stored in Flash memory area. • 256 Mbit Nand Memory for Multimedia IC - 16 -...
3. Technical Brief 3.5 Power Management Section • VRDBB: supplies Digital Baseband Processor core (1.8V, 1.4V, and 1.2V, 170mA) • VRMEM: supplies external memory and digital baseband memory interface I/Os (1,8V or 2.8V, 60mA) • VSIM: supplies the SIM card and SIM card driver (1.8V or 2.9V, 20mA) •...
Page 17
3. Technical Brief 3.5.1 MIDI • The ringing source of LG-KG330 is the MIDI IC • LG-KG330 uses 8 bit parallel interface. • The MIDI chip which is used in LG-KG330 is • Support differential Mono output & stereo YMU 783 from Yamaha.
Page 21
3. Technical Brief 3.5.5 SIM • SIM Interface - SIM interface scheme is shown below. SIM_IO, SIM_CLK, SIM_RST ports are used to communicate DBB with ABB and the Charge Pump in ABB enables. 1.8V/3V SIM operation - SIM_CLK: SIM Card reference clock - SIM_RST : SIM Card async/sync reset - SIM_IO: SIM Card bi-directional data line V_SIM...
Page 22
3. Technical Brief 3.5.6 Keypad • KEYPAD Scanning Scheme (number -key) The power key is connected to TWL3016(ABB) directly using ‘PWON’. The other number-key and side-key is connected to Calypso Plus (DBB) using: SIDE KEY PAD C800 CON800 CAMERA VOL_DOWN VOL_UP KB800 R800...
Page 23
3. Technical Brief Keypad • Jog Encoder Key Scanning Scheme (Navigation key). FD_JOG encoder generates coded signals by displacement of actuator. The shifted timing of output signal between FD_JOG_BDET and FB_JOG_ANT decide its operating directions (clockwise or counterclockwise). FD_JOG_BDET and FD_JOG_ANT signal are connected to GPIO_2 and GPIO_1of DBB respectively.
Page 24
3. Technical Brief Keypad • Rotary Key scanning Scheme (Short Menu Key). Rotary encoder generates M_EN_BDET and M_EN_ANT signals, which are connected to GPIO_4 and GPIO_7 of DBB respectively. Depend on its direction, the Rotary Encoder Key move up or down on screen.
4. TROUBLE SHOOTING 4. Troubleshooting BaseBand Part Troubleshooting 4.1 Power On Trouble (1) • Trouble Shooting Setup - Connect PIF-UNION to the phone. - Set the AID-remote switch at PIF-UNION off. • Trouble Shooting Procedure - Check Battery Voltage - END_KEY Dome Switch condition - Check the output voltages of all LDOs.
4. TROUBLE SHOOTING Power On Trouble (2) Test Point VABB VUSB VDBB VSIM VBAT VMEM VRTC • Check point - Battery Voltage - Power on Key Detection - Output of LDOs - 29 -...
Page 29
4. TROUBLE SHOOTING Checking Flow START Check Battery Voltage Charge or Change Battery > 3.4V ? Push power-on key Check the contact of power key And check the level change Or dome-switch of PWON Check the voltage of Replace U100 The LDO outputs at U100 VABB=2.8V VDBB=1.5V...
4. TROUBLE SHOOTING 4.2 Charging Trouble (1) Circuit Diagram Charging current flow VCUSB VCHG VBAT V_IO U200 ISL6299 CRDL CUR_MON IMIN _PPR _CHG _CHG_STAT ICDL USBON CHG_EN PGND C202 Test Point • Charging Procedure - Connecting TA & Charger Detection - Control the charging Current by R221 U200(Charger IC)
Page 31
4. TROUBLE SHOOTING Charging Trouble (2) START The charging adaptor(TA) is out of order. Voltage at VCHG of U200 Change the charging adaptor = 5.2V? U200, R221, R219 Resolder Well-Soldered? U200, R221,R219 Charging is operating properly. Change Voltage at R207 is U200 The battery may have problems.
4. TROUBLE SHOOTING 4.3 LCD Display Trouble (1) • LCD Control signals - From CL8524 :L_RD, L_WR, L_ADS, L_CS ,L_DATA(0:15) From DBB : A(1:3),D(0:15),_WR,_RD • Check point - The assembly status of the LCD Module - The Soldering of connector - The connection between B to B connector and FPCB from LCD Module.
Page 33
4. TROUBLE SHOOTING LCD Display Trouble (2) START Refer to Power is supplied to Power On Trouble the board? Connection between Reconnect FPCB LCD Module and boards is OK? LCD Module is out of order. Change the LCD C704 is soldered well? Module.
4. TROUBLE SHOOTING 4.4 Receiver Trouble (1) Circuit Diagram • Check Points - Audio signals from ABB - Audio signals to the receiver TWL3016 - Audio signal path - Soldering of connector - Connection between EARP Connector and Receiver EARN - Receiver SPKN2 RECEIVER_P...
Page 35
4. TROUBLE SHOOTING Receiver Trouble (2) Test Point Receiver C116,C117:RECEIVERP, RECEIVERN Check Audio signal Soldering here ! Check RECEIVERP, RECEIVERN - 36 -...
Page 36
4. TROUBLE SHOOTING Receiver Trouble (3) START Check the signal level of Check the Replace the Main RECEIVERP AND soldering board. ABB is out RECIEVERN at C116, C166,C167 of order. C117. Are these levels about 1.2V? soldering C166,C167 Check again Check the CONNECTION Re-connecting receiver OF RECEIVER.
4. TROUBLE SHOOTING 4.5 Speaker Trouble (1) Circuit Diagram V_IO 2V8_AVDD VBAT U503 generates Ring tone and provide Amplifier for C519 C518 C520 C514 C515 C516 C517 C521 C513 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u MP3 sound near to V_IO L503 HPOUTR HF_R...
Page 38
4. TROUBLE SHOOTING Speaker Trouble (2) Test Point C535 C536 U209 Soldering Check Speaker - 39 -...
Page 39
4. TROUBLE SHOOTING Speaker Trouble (3) SETTING : Connect PIF to the phone, and Power on. Enter the engineering mode, and set "Melody on" at Buzzer of BB test menu. START Voltage of Change the C515, C518 board about Vbat? Voltage at Change the C535,C536...
4. TROUBLE SHOOTING 4.6 Microphone Trouble (1) Circuit Diagram MAIN_MIC_CKTs R505 MICBIAS C532 C530 R506 2.4K 100nH 0.1u C534 MICP MIC500 L509 C538 100nH 0.1u C537 MICN L510 BOS-T1342SDN3-LH R511 VA505 C542 C543 VA506 • Microphone Signal Flow • Check Points - MIC is enabled by MICBIAS - Microphone bias level - MICBIAS is supplied by ABB...
Page 41
4. TROUBLE SHOOTING Microphone Trouble (2) Test Point - Trouble Shooting Procedure - Check the bias of the microphone. - Check the audio signal path. - Check the soldering. - Check the microphone. R505:MICBIAS - 42 -...
Page 42
4. TROUBLE SHOOTING Microphone Trouble (3) START Voltage at Redownload R505 Change Main Board is about Software 2.5V? Good MIC Bias Voltage Check the signal level at Replace the each side of MIC Connector microphone Is it a few tens mVAC? Check the soldering of Re-solder L509, L510, L509, L510, C534, C537...
4. TROUBLE SHOOTING 4.7 Vibrator Trouble (1) Circuit Diagram VBAT VIBRATOR_CKTs C503 U501 CON502 VOUT BGND R501 VIBRATOR C506 STBY 1.5K (From YAMAHA) Current Flow BH28FB1WHFV C509 C510 2.2u D501 1SS352-TPH3_F When the vibrator works, the VIBRATOR signal at this point goes High •...
Page 44
4. TROUBLE SHOOTING Vibrator Trouble (2) Test Point U501 R501 CN502 C503 • Trouble Shooting Procedure • Check Points - Check vibrator signal - VCC lines of MIDI chip - Check vibrator - Vibrator signal path - The soldering of components - LDO - The Vibrator - 45 -...
Page 45
4. TROUBLE SHOOTING Vibrator Trouble (3) START Replace Is the voltage at pin 1 MIDI(U503) of R501 high? Check the soldering Replace U501 of U501 Check the contact state Change the main board of CN502 Change the vibrator. Check the vibrator Replace Vibrator.
4. TROUBLE SHOOTING 4.8 Keypad Backlight Trouble Test Point Circuit Diagram VBAT KEY BACKLIGHT R708 R709 R710 R711 R712 R713 R714 R715 R718 Q700 KEY_BACKLIGHT 2SC5585 (GPO_0) R719 C741 R720 R721 • Backlight Operation • Check Point - The keypad LED backlight is controlled with - KEY_BACKLIGHT and Signal Key_Backlight signal.
Page 47
4. TROUBLE SHOOTING Keypad Backlight Trouble START Charge battery Is the voltage level VBAT 3.6-4.2V? Check the soldering of each R or Are all LEDs LD100-LD101 LD700-LD707 replace LEDs not working. Working? BACKLIGHT WILL WORK PROPERLY - 48 -...
Page 49
4. TROUBLE SHOOTING Touch Pad Trouble START Connect. Is B to B connected? Check the soldering Replace U702 Of C744 and C101 Are they 3.3V? Replace Touch FPCB. Vibrator will work properly - 50 -...
4. TROUBLE SHOOTING 4.10 Jog Encoder Trouble Test Point R105 R106 R109 R110 Circuit Diagram ROTARY ENCODER V_IO V_IO SW100 R109 R110 FD_JOG_BDET FD_JOG_AINT (GPIO _2) (GPIO _1) C105 C106 0.1u 0.1u • Jog Encoder Operation • Check Point - Up, down and confirm key - V_IO - FD_JOG_BDET and FD_JOG_ANT signal - FD_JOG_ANT, FD_JOG_BDET, signals...
Page 51
4. TROUBLE SHOOTING Jog Encoder Trouble START Check the voltage of Re Download R105, R106 Are they 2.8V Re-solder R109, R110 Check the soldering of R109, R110, R105, R106 R105, R106. Replace JOG Check JOG Encoder Encoder 1. JOG Encoder will work properly - 52 -...
4. TROUBLE SHOOTING 4.11 Rotary Trouble Test Point R102 R103 R107 R108 Circuit Diagram FD_JOG_ENCODER V_IO CON100 R102 R103 R107 R108 M_EN_AINT M_EN_BDET (GPIO _7) (GPIO _4) C102 C104 0.01u 0.01u • Jog Encoder Operation • Check Point - Up, down short menu key - V_IO - M_EN_AINT and M_EN_BDET signals go - M_EN_AINT and M_EN_BDET signal...
Page 53
4. TROUBLE SHOOTING Rotary Trouble START Check the voltage of Re Download R102, R103 Are they 2.8V Re-solderR107, R108. Check the soldering of R107, R108 Check Rotary Encoder Replace Rotary Encoder Rotary will work properly - 54 -...
4. TROUBLE SHOOTING 4.12 SIM Detect Trouble (1) Test Points Circuit Diagram R228 V_SIM V_SIM R228 CON201 SIM_RST SIM_IO SIM_CLK J101 CON201 C209 C210 C211 C212 C213 0.1u 150p 150p C212 • Connection between SIM and ABB • Trouble Shooting Setup - SIM_CLK, SIM_IO, SIM_RST - Insert the SIM into socket - Connect PIF to the phone, and power on.
Page 55
4. TROUBLE SHOOTING SIM Detect Trouble (2) START Change the SIM. Our Phone Does the SIM supports 3V? supports 3V SIM only Check the Resolder or condition of replace CON201 CON201. Good? Voltage of pin 1 Check CON201=2.85V Good? Replace Change SIM card download Main board...
Page 57
4. TROUBLE SHOOTING Earphone Trouble (1) Circuit Diagram Mic-bias (the same as main mic) Close to EAR-JACK R802 INSTPAR HSBIAS D800 C801 C802 C803 R803 DC BLOCKING CAP. 2.2K C804 0.1u R804 100nH HSMIC C805 100u R805 HSO_R C806 100u R807 HSO_L Close to EAR-JACK...
Page 58
4. TROUBLE SHOOTING Earphone Trouble (2) START cf) PRBS : Pseudo Random Bit Sequence Insert the earphone to the handset. Earphone detect problem Does the audio Profile of the phone change to the earphone mode? Audio path problem Set the audio part of test equipment to PRBS Set the audio part of the...
Page 59
4. TROUBLE SHOOTING Earphone Trouble (3) Earphone detect problem Check CON801 Level of R813 is Or replace about 0? Earphone Software Change the Re-download main board - 60 -...
Page 60
4. TROUBLE SHOOTING Earphone Trouble (4) CW signal Change the appears at L504 main board and L506 Soldering CW signal status of C805, Re-solder C805, C806, appears at pin 4, C806, R805, and R805, and R807 5 of CN801 R807 Change the Change the Level of R137 is...
Page 61
4. TROUBLE SHOOTING Earphone Trouble (5) MP3 signal Change the appears at L503 main board and L505 Soldering CW signal status of C805, Re-solder C805, C806, appears at pin 4, C806, R805, and R805, and R807 5 of CN801 R807 Change the Change the EARJACK...
Page 62
4. TROUBLE SHOOTING Earphone Trouble (6) Earphone sending path problem Voltage at Re-solder R813 is 2.5V? R813 Level of C804 is Re-download Re-solder about a few tens software. or hundreds VAC? C804 Change Does it work well? main board Does it work well? - 63 -...
Page 67
4. TROUBLE SHOOTING Camera Trouble (3) START Does LCD work properly? Go to the LCD Trouble Set the Camera Check CN816Contact button ON Check power 2.6V Replace U604 (At R821) Check power 1.8V (At R820) Re-contact CN816 Check the 24MHz waveform? Replace MainBoard 3 Pin (At FL803) Change the...
Page 69
4. TROUBLE SHOOTING Camera Flash Trouble (2) START Set the Camera Flash ON Replace Flash LED Check VOUT Check FLASH_EN working? : 3.4~3.7V (R618) : HIGH BOARD Replace U604 Camera flash Change the will work Properly Camera FLASH LED • Camera Flash operation •...
Page 79
4. TROUBLE SHOOTING For these 2 test case, No Call connection is needed Open Change CN400 Check CN400 Pin ANT,RF with RF Cable connected. Change CN400 Short Check CN401 Pin ANT,RF with No RF Cable Connected Check R421,R422 EGSM=> Check if ANT_SW is set as sw1:low/sw2:low Change the Board.
Page 80
4. TROUBLE SHOOTING 5. Checking Rx I/Q U401 C418 C425 Check C418, C425. Similar? Check if there is Change U401 any major Difference Redownload the Software and calibrate - 81 -...
Page 86
4. TROUBLE SHOOTING 3.Checking RF Chipset Control Signal Check SCLK,SENB,SDI U401 Refer to Graph Redownload Similar? Phone S/W Control Signal OK. See next page check. SENB SCLK R412 SCLK SCLK R413 _SEN SENB R414 SDIO U401 RXQN SI4210D RXQP RXIN RXIP XOUT R415...
Page 87
4. TROUBLE SHOOTING 3.Checking RF Chipset Control Signal - 88 -...
Page 88
4. TROUBLE SHOOTING 4. Checking Tx I/Q U401 C418 C425 Check C418, C425. Similar? Change U401 Check if there is any major Difference Redownload the Software and calibrate - 89 -...
Page 90
4. TROUBLE SHOOTING 5. Checking PAM Circuit GSM_TX Output U400 U400 PA_ON DCS_PCS TX Output PA_BAND Check control signals of Similar? Download S/W U400 refer to waveform Check if there is Go to Next Step any major difference - 91 -...
Page 93
4. TROUBLE SHOOTING 6. Checking FEM & Mobile Switch For these 2 test case, No Call connection is needed Open Change CN400 Check CN400 Pin ANT,RF with RF Cable connected. Short Change CN400 Check CN401 Pin ANT,RF with No RF Cable Connected Check R421,R422 EGSM=>...
5. Downloading Software 5. Downloading Software 5.1 The Environment of Downloading Software 1. In case of using the Data kit Describes Download Setup Preparation • Target Handset • Data kit • Battery • IBM compatible PC supporting RS-232 with Windows 98 or newer If you use data kit, you should have a battery with the voltage above 3.7V.
5. Downloading Software 5.2 The Procedure of Downloading Software(1) 1. Computer Program file -> MultiGSM.exe Click - 96 -...
Page 96
5. Downloading Software The Procedure of Downloading Software(2) 2. Click the “Setting” button. Then, choose Configuration which is going to download. - 97 -...
Page 97
5. Downloading Software The Procedure of Downloading Software(3) 3. Configuration Setting C:\GSMULTI\Model\KG330dll - 98 -...
Page 98
5. Downloading Software The Procedure of Downloading Software(4) 4. Press “Start Button”. MG210 - 99 -...
Page 99
5. Downloading Software The Procedure of Downloading Software(5) 5. After “Start Button”, Which Stand-by condition MG210 - 100 -...
Page 100
5. Downloading Software The Procedure of Downloading Software(6) 6. SW downloading Condition. MG210 - 101 -...
Page 101
5. Downloading Software The Procedure of Downloading Software(7) 7. SW downloading END Condition. MG210 - 102 -...
Main 1/8 M_EN_BDET C144 2006 BT_LDO_EN OUT2 _CHG_STAT EN_SET Checked MAP_HOLD OUT3 J.H. BAE DRAWING DBB & ABB CHG_EN TCH_LDO_EN OUT4 NAME GPIO_CON GPIO_CON Approved HP_PATH_SEL OUT5 KEY_BACKLIGHT DRAWING REV_1.0 LG Electronics Inc. LG Electronics Inc. LGIC(42)-A-5505-10:01 - 105 -...
Page 105
Section Sign & Name Date Sheet/Sheets KG330 MODEL 06/02 Designer S.D. KIM Main 2/8 2006 Checked J.H. BAE DRAWING I/O CONNECTOR NAME Approved DRAWING REV_1.0 Iss. Notice No. Date Name LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 106 -...
Page 106
Section Sign & Name Date Sheet/Sheets KG330 MODEL 06/02 Designer J.W.KIM Main 3/8 2006 Checked J.H. BAE DRAWING Bluetooth & Memory NAME Approved DRAWING Iss. Notice No. Date Name REV_1.0 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 107 -...
Page 107
J.W.KIM 22K Thermistor GND1 2006 RF_LDO_EN GND2 C434 R426 Checked C435 C436 J.H. BAE DRAWING 1000p RF Ckts TEMPSENSE NAME Approved R427 4.7K DRAWING REV_1.0 Iss. Notice No. Date Name LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 108 -...
Page 108
VO_REC_N MIDI_SPKPHN_HS_CKTs Section Date Sign & Name Sheet/ KG330 MODEL Sheets 06/02 Designer S.D. KIM 2006 Checked J.H. BAE DRAWING MIDI&VIB&MIC NAME Approved DRAWING REV_1.0 Iss. Notice No. Date Name LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 109 -...
Page 109
Sign & Name Sheet/ KG330 L_CS MODEL Sheets L_WR 06/02 Designer S.D. KIM L_RD 2006 L_ADS Checked J.H. BAE DRAWING MAP&NAND&CHG_PU NAME Approved DRAWING REV_1.0 Iss. Notice No. Date Name LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 110 -...
Page 110
KG330 (GPIO_5) MODEL Sheets I2C_DATA_TCH 06/02 Designer S.D. KIM (GPIO_10) 2006 I2C_CLK_TCH (GPIO_9) Checked C744 J.H. BAE C745 DRAWING LCD&T_FLASH&F_IF 0.1u NAME Approved DRAWING REV_1.0 Iss. Notice No. Date Name LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 111 -...
Page 111
C_RST S.D. KIM 2006 C_MCLK INOUT_B3 INOUT_A3 INOUT_B4 INOUT_A4 V_IO Checked (10 ohm, 7.5pF) J.H. BAE C820 C819 DRAWING KEY&EAR_J&CAMERA 0.1u NAME Approved DRAWING REV_1.0 Iss. Notice No. Date Name LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 112 -...
Page 112
TP101 TP102 TP103 Section Date Sign & Name Sheet/Sheets MODEL BUDDY 06/02 Designer S.D. KIM 2006 Checked DRAWING IF_BOARD NAME Approved J.H. BAE DRAWING Iss. Notice No. Date Name REV_1.0 LG Electronics Inc. LG Electronics Inc. LGIC(42)-A-5505-10:01 - 113 -...
Page 113
M_EN_BDET M_EN_AINT M_EN_BDET Section Date Sign & Name Sheet/Sheets MODEL BUDDY 06/02 Designer S.D. KIM 2006 Checked J.H. BAE DRAWING ENCODER NAME Approved DRAWING Iss. Notice No. Date Name REV_1.0 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 114 -...
Page 114
I2C_DATA_TCH R104 TOUCH_ACK Section Date Sign & Name Sheet/Sheets MODEL BUDDY 06/02 Designer S.D. KIM 2006 Checked J.H. BAE DRAWING FPCB NAME Approved DRAWING REV_1.0 Iss. Notice No. Date Name LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 115 -...
9. Calibration 9.2 Standalone Test 1. What is the Standalone Test Set the Phone to Perform only Tx or Rx mode for monitoring performance of Tx part or Rx part only 1. Normal Call 2. Standalone • During Rx Standalone •...
Page 125
9. Calibration 3. TX Standalone Test Setup 1. Setting the Test Equipment as ‘Test Mode-BCH’ Example) For HP8960 On the Control Window Operating Mode: Test Test Function: BCH For HP8922 Operating mode: Test Mode 1. Setting Channel and Power - 126 -...
Page 127
9. Calibration 4. RX Standalone Test Setup 1. Setting the Test Equipment as ‘CW Mode’ Example) For HP8960 On the Control Window Operating Mode: Test Test Function: CW For HP8922 Operating mode: CW Generator 2. Setting Channel and Power - 128 -...
10. EXPLODED VIEW & REPLACEMENT PART LIST 10.2 Replacement Parts Note: This Chapter is used for reference, Part order is ordered by SBOM standard on GCSC <Mechanic component> Location Level Description Part Number Specification Color Remark GSM,BAR/FILP TGSM0044601 Black AAAY00 ADDITION AAAY0144101 ACGA00...
Page 133
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark MGAB00 GASKET,EMI MGAB0013701 REAR Yellow MGAB01 GASKET,EMI MGAB0015301 COMPLEX, (empty), , , , , Yellow MIDZ00 INSULATOR MIDZ0113001 COMPLEX, (empty), , , , , Blue MLAB00 LABEL,A/S MLAB0000601...
Page 134
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark MTAZ05 TAPE MTAZ0158201 COMPLEX, (empty), , , , , MTAZ06 TAPE MTAZ0160301 COMPLEX, (empty), , , , , Black ASSY ,104 dB,32 ohm,09*06 ,3T ,; ,30mW(50mW) , , , , SURY00 RECEIVER SURY0012401...
Page 135
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark MPBZ00 MPBZ0151501 COMPLEX, (empty), , , , , Black MPBZ01 MPBZ0151601 COMPLEX, (empty), , , , , Black - 136 -...
10. EXPLODED VIEW & REPLACEMENT PART LIST 10.2 Replacement Parts Note: This Chapter is used for reference, Part order is ordered by SBOM standard on GCSC <Main component> Location Level Description Part Number Specification Color Remark SAFY00 PCB ASSY,MAIN SAFY0159301 SAFB00 PCB ASSY,MAIN,INSERT SAFB0058701...
Page 137
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C103 CAP,CHIP,MAKER ECZH0000826 27 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C104 CAP,CHIP,MAKER ECZH0000826 27 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C120 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP CONNECTOR, CN100 ENBY0019101...
Page 138
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C116 CAP,CERAMIC,CHIP ECCH0000122 47 pF,50V,J,NP0,TC,1005,R/TP C117 CAP,CERAMIC,CHIP ECCH0000122 47 pF,50V,J,NP0,TC,1005,R/TP C118 CAP,CERAMIC,CHIP ECCH0006201 4.7 uF,6.3V ,K ,X5R ,TC ,1608 ,R/TP C119 CAP,CHIP,MAKER ECZH0000813 100 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C120 CAP,CHIP,MAKER ECZH0000813...
Page 139
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C208 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C209 CAP,CERAMIC,CHIP ECCH0000115 22 pF,50V,J,NP0,TC,1005,R/TP C210 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP C211 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C212 CAP,CERAMIC,CHIP ECCH0000187...
Page 140
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C411 CAP,CERAMIC,CHIP ECCH0000110 10 pF,50V,D,NP0,TC,1005,R/TP C412 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP C413 CAP,CERAMIC,CHIP ECCH0000115 22 pF,50V,J,NP0,TC,1005,R/TP C414 CAP,CHIP,MAKER ECZH0000802 1 pF,50V ,C ,NP0 ,TC ,1005 ,R/TP C415 CAP,CERAMIC,CHIP ECCH0000143...
Page 141
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C515 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP C518 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP C520 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C521 CAP,CERAMIC,CHIP ECCH0000182...
Page 142
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C700 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C701 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C705 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP C706 CAP,CERAMIC,CHIP ECCH0004904...
Page 143
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark L103 INDUCTOR,CHIP ELCH0005009 100 nH,J ,1005 ,R/TP , L104 INDUCTOR,CHIP ELCH0005009 100 nH,J ,1005 ,R/TP , L301 INDUCTOR,CHIP ELCH0005005 27 nH,J ,1005 ,R/TP , L302 INDUCTOR,CHIP ELCH0005005 27 nH,J ,1005 ,R/TP ,...
Page 144
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R128 RES,CHIP,MAKER ERHZ0000360 100 Kohm,1/16W ,D ,1005 ,R/TP R129 RES,CHIP,MAKER ERHZ0000402 10 ohm,1/16W ,J ,1005 ,R/TP R130 RES,CHIP,MAKER ERHZ0000405 10 Kohm,1/16W ,J ,1005 ,R/TP R131 RES,CHIP,MAKER ERHZ0000213 120 Kohm,1/16W ,F ,1005 ,R/TP...
Page 145
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R223 RES,CHIP,MAKER ERHZ0000401 0 ohm,1/16W ,J ,1005 ,R/TP R224 RES,CHIP,MAKER ERHZ0000438 20 Kohm,1/16W ,J ,1005 ,R/TP R225 RES,CHIP,MAKER ERHZ0000466 33 Kohm,1/16W ,J ,1005 ,R/TP R226 RES,CHIP,MAKER ERHZ0000360 100 Kohm,1/16W ,D ,1005 ,R/TP...
Page 146
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R421 RES,CHIP ERHY0003501 220 ohm,1/16W ,J ,1005 ,R/TP R422 RES,CHIP ERHY0003501 220 ohm,1/16W ,J ,1005 ,R/TP R423 RES,CHIP,MAKER ERHZ0000422 15 Kohm,1/16W ,J ,1005 ,R/TP R501 RES,CHIP,MAKER ERHZ0000529 1.5 Kohm,1/16W ,J ,1005 ,R/TP...
Page 147
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R806 RES,CHIP,MAKER ERHZ0000505 680 ohm,1/16W ,J ,1005 ,R/TP R807 RES,CHIP,MAKER ERHZ0000488 4.7 ohm,1/16W ,J ,1005 ,R/TP R808 RES,CHIP,MAKER ERHZ0000505 680 ohm,1/16W ,J ,1005 ,R/TP R809 RES,CHIP,MAKER ERHZ0000505 680 ohm,1/16W ,J ,1005 ,R/TP...
Page 148
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark VA202 VARISTOR SEVY0003901 5.5 V, ,SMD ,480pF, 1005 VA501 VARISTOR SEVY0001001 14 V, ,SMD ,50pF, 1005 VA502 VARISTOR SEVY0001001 14 V, ,SMD ,50pF, 1005 VA503 VARISTOR SEVY0001001 14 V, ,SMD ,50pF, 1005...
Page 149
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C629 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C630 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C631 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP C632 CAP,CERAMIC,CHIP ECCH0000182...
Page 150
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C737 CAP,CHIP,MAKER ECZH0000826 27 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C738 CAP,CHIP,MAKER ECZH0000826 27 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C739 CAP,CERAMIC,CHIP ECCH0000112 15 pF,50V,J,NP0,TC,1005,R/TP C740 CAP,CERAMIC,CHIP ECCH0000112...
Page 151
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R103 RES,CHIP,MAKER ERHZ0000459 3 Kohm,1/16W ,J ,1005 ,R/TP R105 RES,CHIP,MAKER ERHZ0000405 10 Kohm,1/16W ,J ,1005 ,R/TP R106 RES,CHIP,MAKER ERHZ0000405 10 Kohm,1/16W ,J ,1005 ,R/TP R107 RES,CHIP,MAKER ERHZ0000459 3 Kohm,1/16W ,J ,1005 ,R/TP...
Page 152
10. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R803 RES,CHIP,MAKER ERHZ0000443 2200 ohm,1/16W ,J ,1005 ,R/TP R804 INDUCTOR,CHIP ELCH0005009 100 nH,J ,1005 ,R/TP , R811 RES,CHIP,MAKER ERHZ0000477 390 Kohm,1/16W ,J ,1005 ,R/TP R812 RES,CHIP,MAKER ERHZ0000477 390 Kohm,1/16W ,J ,1005 ,R/TP...
Specification Color Remark MBAD00 BAG,VINYL(PE) MBAD0008001 MCJA00 COVER,BATTERY MCJA0031601 ADEY00 DATA KIT ADEY0001074 KG330/KG338 Data Kit for English MBAZ00 MBAZ0004701 CD Cover MCHZ00 COMPACT DISK MCHZ0024801 COMPLEX, (empty), , , , , Black MMBA00 MANUAL,INSTALLATION MMBA0018501 Installation guide for Mobile Agent...