Summary of Contents for Kramer Tavor 8-Sub
-
Page 1: User Manual
K R A ME R E LE CT R O N IC S L TD . USER MANUAL MODEL: Tavor 8-Sub Powered Subwoofer P/N: 2900-300397 Rev 1... -
Page 3: Table Of Contents
Figure 4: Connecting via LFE Figure 5: Connecting via Line Input Figure 6: Connecting via High Level Input Figure 7: Connecting to an Active Speaker Figure 8: Installing the Bracket Figure 9: Mounting Tavor 8-Sub over the Bracket Tavor 8-Sub – Contents... -
Page 4: Introduction
Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront video, audio, presentation, and broadcasting professionals on a daily basis. In recent years, we have redesigned and upgraded most of our... -
Page 5: Getting Started
Avoid interference from neighboring electrical appliances that may adversely influence signal quality Position your Kramer Tavor 8-Sub away from moisture, excessive sunlight and dust This equipment is to be used only inside a building. It may only be connected to other equipment that is installed inside a building. -
Page 6: Recycling Kramer Products
Kramer Electronics has made arrangements with the European Advanced Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular country go to our recycling pages at http://www.kramerelectronics.com/support/recycling/. -
Page 7: Overview
The Tavor 8-Sub can be mounted on the wall, on the floor or next to the wall in a way that hides the control panel. -
Page 8: Figure 1: Tavor 8-Sub Front Panel
Figure 1 shows the front panel and Figure 2 shows the Tavor 8-Sub rear panel: Figure 1: Tavor 8-Sub Front Panel Figure 2: Tavor 8-Sub Rear Panel Tavor 8-Sub - Overview... -
Page 9: Defining The Tavor 8-Sub
Defining the Tavor 8-Sub This section defines the active Tavor 8-Sub: Figure 3: Tavor 8-Sub Active Speaker Tavor 8-Sub - Defining the Tavor 8-Sub... - Page 10 POWER Settings Slide Switch Set to 110-120V or to 220-240V ON Switch Set to ON to power the Subwoofer Power Connector with Fuse AC connector, enabling power supply to the unit Tavor 8-Sub - Defining the Tavor 8-Sub...
-
Page 11: Installing The Tavor 8-Sub
Position your subwoofer on a hard surface or hang it on the wall: Keep the vibrations to a minimum Do not cover or place anything on the Tavor 8-Sub Before installing the subwoofer: Experiment by placing the subwoofer in different locations and check the... -
Page 12: Tavor 8-Sub Different Setups
6. Turn the volume all the way down. 7. Play a track with deep bass and rich in low frequencies. 8. Listen to the bass line and set the Tavor 8-Sub volume to the point where the bass sounds most balanced. The subwoofer should not be louder compared to the rest of the system;... -
Page 13: Figure 4: Connecting Via Lfe
HIGH LEVEL INPUT, see Section 5.3.3 You can also connect the Tavor 8-Sub to an active speaker as described in Section 5.3.4. Sending a 50W input to the Hi-Level inputs and setting full volume on the LFE inputs – might damage the Tavor 8-Sub. -
Page 14: Figure 5: Connecting Via Line Input
2. Connect the receiver subwoofer output right RCA connector to the R LINE LEVEL INPUT RCA connector, via an RCA cable. Use the CROSSOVER control button on the Tavor 8-Sub to set the optimal crossover frequency of the system. Figure 5: Connecting via Line Input... -
Page 15: Figure 6: Connecting Via High Level Input
Connecting to a Receiver via the High Level Input If the receiver does not have a dedicated subwoofer output, connect it to the Tavor 8-Sub using the receiver’s speaker outputs via regular speaker wires. The low frequencies will be set via the Crossover control knob. -
Page 16: Figure 7: Connecting To An Active Speaker
Connecting to an Active Speaker via the Line Level Input When using an active speaker, for example the Tavor 5-O, you can connect the Tavor 8-Sub directly to the speaker via its SUB OUT connector using the Kramer Mini Jack (3.5mm) to RCA cable (C-A35M/2RAM) as illustrated in... -
Page 17: Mounting The Tavor 8-Sub On The Wall
Mounting the Tavor 8-Sub on the Wall You can place the Tavor 8-Sub vertically or horizontally or use the specially designed wall mount bracket included in the package to hang the Tavor 8-Sub on the wall at the desired location. - Page 18 4. Pass the wiring through the opening in the bracket. 5. Lift the Tavor 8-Sub and place the groove on the subwoofer over the bracket. Figure 9: Mounting Tavor 8-Sub over the Bracket Tavor 8-Sub - Mounting the Tavor 8-Sub on the Wall...
-
Page 19: Technical Specifications
45cm x 40cm x 20.5cm (17.7” x 15.7” x 8.1”), W, D, H. DIMENSIONS: INCLUDED ACCESSORIES: Power cable COLORS: Available in white Specifications are within a 10% tolerance and are subject to change without notice at http://www.kramerelectronics.com Tavor 8-Sub - Technical Specifications... - Page 21 This page is intentionally left blank...
- Page 22 For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback. Web site: www.kramerelectronics.com E-mail: info@kramerel.com SAFETY WARNING...
Need help?
Do you have a question about the Tavor 8-Sub and is the answer not in the manual?
Questions and answers