Wisnetworks WIS-Q2300 User Manual
  1. Manuals
  2. Brands
  3. Wisnetworks Manuals
  4. Wireless Access Point
  5. WIS-Q2300
  6. User manual

Wisnetworks WIS-Q2300 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

WIS-Q2300 User Manual
WIS-Q2300 User Manual
V1.0
Page 1 , Total 26

Advertisement

Table of Contents
loading

Summary of Contents for Wisnetworks WIS-Q2300

  • Page 1 WIS-Q2300 User Manual WIS-Q2300 User Manual V1.0 Page 1 , Total 26...

  • Page 2: Configuration Preparation

    WIS-Q2300 User Manual 1. Application Thank you for your purchase WIS-Q2300。This handbook is to help you know and configure WIS-Q2300. 2. Configuration Preparation 2.1 Installation Device Figure 1  Press the clip of 2.4GHz CPE，pull out the cover，stick one end of cable into ETH port; Slide the cover until the clip locked.

  • Page 3: Configuration Instruction

    WIS-Q2300 User Manual Figure 2 3. Configuration Instruction Main Page After logining enter automatically into Main Page, as shown. Status has 3 status label pages, Wireless、 Network and System Page. The below is introduced separately. Page 3 , Total 26...
  • Page 4 WIS-Q2300 User Manual Figure 3-1 3.1.1 WIRELESS Page Radio status box mainly shows work mode and RF information of 2.4GHz CPE.  Wireless mode：working mode of 2.4GHz CPE, supporting 4 kinds of working mode, AP Mode、Station Mode、AP WDS Mode and Station WDS Mode；...

  • Page 5: Network Page

    WIS-Q2300 User Manual sending rate. If AP and Station can reach to 40MHz channel bandwidth, max sending rate can reach to 300Mbps, and throughout rate can improve more than twice. Station status box shows CPE working as Station Mode. ...
  • Page 6 WIS-Q2300 User Manual Figure 3-2 Network Mode of Network Role status box shows current network mode.  Network Mode: device supports 3 kinds of Network Modes, namely Bridge Mode、SOHO Router Mode and WISP Mode. We will have a brief introduction to those: 1.

  • Page 7: Interfaces List

    WIS-Q2300 User Manual  Bridge Mac： MAC address of bridge interface；  Gateway： gateway IP Address of bridge interface；  Primary DNS IP： primary DNS address of bridge interface；  Secondary DNS IP： secondary DNS address of bridge interface； 3.1.3 SYSTEM Page This page mainly shows version, device name and so on, as shown Figure 3-3.

  • Page 8: Arp List

    WIS-Q2300 User Manual Figure 3-4  Interface：listing all interfaces and interface name；  Address：listing MAC address of all interfaces；  Bytes：sending bytes number；  Packet：sending packet ；  Err：sending error packet ；  Bytes：receiving bytes ；  Rx Packet: receiving packet；...
  • Page 9 WIS-Q2300 User Manual  AID: connecting ID of STA；  Signal：AP detected RSSI of STA；  Assoc Time：time online of STA；  Tx/Rx Packets：send-receive packets between AP and STA. Tx means sending packets from AP to STA, Rx means receiving packets from STA to AP；...

  • Page 10: Routes List

    WIS-Q2300 User Manual 3.1.8 Routes List Routes list shows current routing relationship of device, as Figure 3-8. Figure 3-8  Destination: destination address and mask;  Gateway：next address against destination address, that is gateway address.  Flags：network type of this routing info;...

  • Page 11: Dhcp Server List

    WIS-Q2300 User Manual  RX Bytes: CPE receiving bytes by PPP interface. 3.1.10 DHCP Server List DHCP Server List shows status of assigning IP address when CPE is DHCP Server, as Figure 3-10。 Figure 3-10  Address：MAC address of DHCP Client；...

  • Page 12: Basic Wireless Settings

    WIS-Q2300 User Manual 3.2.1 Basic Wireless Settings  Wireless Mode：used for working mode of WLAN, 2.4GHz CPE supporting AP Mode, Station Mode, AP WDS Mode and Station WDS Mode, the default is Station Mode. Because settings of those 4 modes have little impact to parameter setting of whole Radio,we will not introduce parameter setting of Radio for 4 modes.

  • Page 13: Wireless Page

    WIS-Q2300 User Manual will trigger aggr limit. WIRELESS Page Wireless Page is used for setting wireless service of AP Mode or relevant parameters for Station Mode connecting AP . 3.3.1 AP/AP WDS Mode When CPE is set as AP/AP WDS Mode, Wireless Page is shown as Figure 3-12.
  • Page 14 WIS-Q2300 User Manual  Security：used for setting security type, the default is None.； If choosing WEP security type，as shown Figure 3-13. Figure 3-13  Authentication Type：used for setting authentication method, the default is open；  WEP Key Length：used for setting WEP key length, the default is 64 bit；...
  • Page 15 WIS-Q2300 User Manual Figure 3-15 Wireless Settings  SSID: When CPE is set as Station Mode, enter here SSID of linked AP. If just enter SSID not AP MAC address, CPE will choose the strongest signal among homonym SSID to link.

  • Page 16: Network Page

    WIS-Q2300 User Manual  Lock to AP: locking it as wireless service that CPE will connect. Wireless Security There is no more introduction for choosing it according to authentication method and encryption way. NETWORK Page NETWORK Page is used for setting relevant parameters of network mode. As told before, 2.4GHz CPE is supporting Bridge Mode, SOHO Router Mode and WISP Mode.

  • Page 17: Management Network Settings

    WIS-Q2300 User Manual  Network Mode: used for setting current network mode. 2. Management Network Settings  Bridge IP Address: Bridge IP address obtaining way, separately static set and DHCP access；  IP Address: used for setting static IP address；...
  • Page 18 WIS-Q2300 User Manual Figure 3-18 Network Role  Network Mode : used for setting current network mode. 2. WAN Network Settings  WAN IP Address: WAN IP adsress obtaining way, separately static set, DHCP access and PPPoE negoiation. Because static set and DHCP access are the same with setting of Bridge Mode, there is directly introduction PPPoE；...

  • Page 19: Services Page

    WIS-Q2300 User Manual  MTU/MRU: used for setting MTU and MRU PPPoE negoiation；  used for setting MPPE Agreement when“enable” or “to enable” PPPoE negoiation is using Encryption: （Microsoft Point-to-Point Encryption Agreement） ；  NAT：used for setting NAT service of “enable” or “to enable”CPE；...

  • Page 20: Web Server

    WIS-Q2300 User Manual Figure 3-19 3.5.1 Web Server  Server Port: used for setting server port of web service, the default is 80；  Session Timeout: used for setting web session timeout, the default is 15 minutes. 3.5.2 Telnet Server ...

  • Page 21: Security Service

    WIS-Q2300 User Manual  spoofing attack detect: spoofing attack, if enable, prevent outer net linking by using inner net IP；  ping attack detect: ping request, if enable, abandon ping requestof outer net sending；  tcp null scan detect：tcp null scan, if enable, abandon null scan of tcp sending；...

  • Page 22: Mac Control

    WIS-Q2300 User Manual  worm_virus: worm virus, if enable, prevent worm virus attack；  shake_virus: shake virus, if enable, prevent shake virus attack；  shock_virus: shock virus, if enable, prevent shock virus attack；  hackers_horse：hackers horse, if enable, prevent hackers horse attack ；...

  • Page 23: System Page

    WIS-Q2300 User Manual Figure 3-24 ※Attention: MAC Control is available to all ports. Pls be careful to setup. 3.6 SYSTEM Page SYTEM Page is mainly used for setting relevant device management, as Figure 3-25. Page 23 , Total 26...

  • Page 24: Date Settings

    WIS-Q2300 User Manual Figure 3-25 3.6.1 Device  Device Description: used for setting device description；  Enable Startup Date: used for setting enable startup date, the default is enable state；  Startup Date: used for setting device startup date. 3.6.2 Date Settings ...

  • Page 25: System Accounts

    WIS-Q2300 User Manual 3.6.3 System Accounts  Username: used for setting admin username；  Current Password: amending username and new password after entering current password；  New Password: used for setting new password；  Verify New Password: used for verifying new password.

  • Page 26: Specification

    WIS-Q2300 User Manual 3.6.6 Specification Feature Item Content Passive POE(24V DC) Reset Power:On/Off Hardware LED Indicator LAN1:On/Off/Flashing information RSSI Signal:1,2,3, Ethernet 1 x 10/100M LAN port(Support Passive POE) Power 24VDC/0.8A Frequency Range 2.4~2.4835GHz Antenna 12dBi dual-polarized directional antenna Beamwidth(HPBW) Horizontal: 60°, Vertical: 30°...

Table of Contents