Advertisement
QUINTEZZ LED SENSOR FLOODLIGHT
See Illustration I
1)
Floodlight
2)
PIR Motion Sensor
3)
Wiring cable + connector
4)
Mounting bracket
5)
Adjustment knob
INTRODUCTION
Your QUINTEZZ LED sensor Floodlight is a unique indoor or outdoor lighting system
for your home or business. At night, the built-in infrared (PIR) motion sensor turns
on the Floodlight when it detects motion in its detection field. The built-in light
sensor can be activated during the day in order to save electricity. An adjustable
timer makes you able to select how long the Floodlight needs to stay on after
activation.
A 20W LED light is installed which can be adjusted thanks to the 3 different knobs
located at the bottom of the motion sensor:
1)
SENS (SENSITIVITY): SENS knob
controls the sensitivity, the detection
area : lowest sensitivity = detects all
motion within 5m, highest sensitivity
= detects all motion within 12m.
2)
TIME: TIME knob controls how long
the Floodlight will stay on after the
last motion has been detected.
The minimum TIME is 10sec., the
maximum TIME is 7min.
3)
LUX: LUX knob determines at what
light level the Floodlight will start
working, so it actually controls the
built-in light sensor.
SAFETY PRECAUTIONS
•
Do not install when it is raining
•
Make sure you switch off the power before installation
•
Make sure that the power wiring comes from a circuit with a suitable fuse or
circuit breaker
•
Make sure that there are no objects within a range of 80 cm from the Floodlight
•
Do not remove the adjustment knob (5)
•
Do not remove the Floodlight head assembly and motion sensor from the base,
so as to avoid any rotation
•
The unit can only be installed horizontally, not vertically as shown on illustration II.
IMPORTANT
Some countries may require installation of this product by a qualified electrician.
Please check the laws and requirements in your country. If the house wiring
is of aluminum, consult with an electrician about proper wiring methods.
Before proceeding the installation, TURN OFF THE POWER TO THE LIGHTING
CIRCUIT AT THE CIRCUIT BREAKER OR FUSE BOX TO AVOID ELECTRICAL
SHOCKS.
CHOOSE A MOUNTING LOCATION
•
For the best results, fix the Floodlight on a solid surface at a height between
2.5 ~ 3.8 m.
•
For outdoor installation: a location under eaves is preferable
•
Avoid aiming the motion sensor at pools, heating vents, air conditioners or
objects which may change temperature rapidly
•
Try to avoid pointing the Floodlight at trees or shrubs or where the motion of
pets may be detected
•
Before mounting, please keep in mind that the motion sensor is most sensitive
to all motion appearing across the sensor and less sensitive to all motion
appearing directly towards the sensor (See Illustration III.)
INSTALLATION
Make sure you have a screwdriver and drill ready. Select a location for the unit,
based on the coverage angles shown in Illustration IV.
WIRING INSTRUCTION
1)
Switch off the power source
2)
Remove the mounting bracket from the Floodlight. Drill the wall and screw
the bracket onto the wall using suitable wall plugs and screws (not included).
Check that the bracket is securely fitted onto the wall. See illustration V.
Note: at this stage, do NOT re-attach the Floodlight to the bracket.
3)
Strip approximately 6-8 mm insulating part of the power cable and original
wire (if needed). Before connection make sure that the wiring box gasket is
firmly seated in its original place.
4)
Connect the BROWN wire (live wire +) to the terminal block "L" mark.
Connect the BLUE wire (Neutral wire) to the terminal block "N" mark.
Connect the YELLOW/GREEN wire (earthing wire) to the terminal block
mark. (in case there is an earthing wire).
5)
Re-attach the Floodlight to the bracket and secure the cable to the wall using
suitable clips (not included). Ensure that the cable is not touching the body
of the Floodlight and that there is sufficient slack in the cable to allow the
Floodlight to be titled and adjusted as required which should be done by
grasping the metal body of the Floodlight and determining its position.
6)
Use the adjustment knob (5) to rotate/turn the Motion Sensor in the perfect
position. (see illustration VI).
SETTINGS
1) TEST MODE
•
- Turn the SENS knob clockwise to
the maximum setting.
- Turn the TIME knob anti-clockwise
to the minimum setting.
- Turn the LUX knob clockwise to the
maximum 'sun' (
) setting.
•
When you switch on the power, the controlled power load will not yet work.
Preheating will take 30 sec. As soon as the sensor detects motion, the
Floodlight will turn on. When the Floodlight turns off, it will turn on again
when the sensor detects motion within 5~15 sec.
•
Afterwards make the Floodlight turn itself on after 5-10 sec. This should work
now. When there is no motion signal in the sensor, the Floodlight will turn off.
•
Turn the LUX knob anti-clockwise to the minimum. If it is set to less than 3 LUX
(dark), the light and sensor will not work when testing in daylight. If you cover
the detection window by an opaque object (a towel for example), the light will
turn on. When there is no motion signal, the light will turn off within 5-15 sec.
•
Adjust the motion sensor to choose and set the desired detection field. For
a smaller detection field, point the sensor down; for a larger detection field,
point the sensor up.
Attention: when testing in daylight, please turn LUX knob to the SUN
position, otherwise the Floodlight will not turn on!
Note:
• Should be installed by an electrician or experienced person
• Avoid installation on objects that can move/shrink/expand ...
POSSIBLE PROBLEMS
When sensitivity is poor:
•
Make sure that the detection window is free from dust and dirt which can
affect the sensitivity
•
Make sure that the ambient temperature is not too high
•
Make sure that the motion signal is located within the detection field
•
Make sure that the installation height corresponds to the recommended
height (between 2.5 ~ 3.8 m)
•
Make sure that the motion sensor is correctly oriented to detect motion
signals
GB
SENS
TIME
LUX
Note: please read this entire
manual before you start installing
this product.
SENS
TIME
LUX
When the Floodlight does not turn off automatically:
•
Make sure there isn't a continuous motion signal within the detection field
•
Make sure that the TIME setting is not set to the maximum
•
Make sure that the power corresponds to the instructions
•
Make sure that the temperature near the sensor cannot change rapidly
caused by e.g. air condition, central heating, ...
2) TIME ADJUSTMENT
The TIME adjustment determines how
long the Floodlight will stay on after the
last motion has been detected.
•
Turn the motion sensor TIME knob
counter-clockwise to increase (up to
about 7 minutes) the amount of TIME
the Floodlight will stay on.
•
Turn the motion sensor TIME knob
clockwise to decrease (down to about
10 seconds) the amount of TIME the
floodlight will stay on.
3) LUX ADJUSTMENT
LUX knob determines at what light level the Floodlight
will start working, so it actually controls the built-in light
sensor.
•
Temporarily turn the LUX knob counter-clockwise
to the moon (dusk) (
)setting
In this provisional setting mode the motion sensor
remains inactive during daylight.
•
At dusk when you find it is the desired night level to
start working, simply set it to the position it needs
to become operative as daylight declines.
4)
SENS ADJUSTMENT
SENS knob controls the sensitivity, the
detection area : lowest sensitivity = detects
all motion within 5m, highest sensitivity =
detects all motion within 12m.
•
Turn the motion sensor SENS knob
counter-clockwise to decrease the
sensitivity (lowest level = within 5
meters)
•
Turn the motion sensor SENS knob
clockwise to decrease the sensitivity
(highest level = within 12 m)
OPERATION
Turn on the wall switch (if applicable). When the sensor detects motion, the
Floodlight will automatically turn on. The built-in light sensor turns the sensor off
and on according to the light and time level set by the LUX and TIME knob.
TROUBLESHOOTING
Light does not turn on:
•
Make sure that you have made a correct "wiring connection",
if the load is correctly and there is 220~240V power.
Sensitivity is poor:
•
Make sure that the LUX knob is correctly set
•
Make sure that the SENS knob is correctly set
(also check "Settings / 1. test mode / possible problems")
Light remains ON:
•
Make sure that you have made a correct "wiring connection"
•
Make sure that the TIME knob is correctly set
•
Make sure that the LUX knob is correctly set
Others
Consult your local service agent concerning safety, protections,
regulations, ...
SPECIFICATIONS
Detection method
Power requirement
Lighting Load
Operating Current
Power Cord Requirement
Sensor Power
Protection Class
Waterproof
Operating
Temperature
SENSor adjustments
Swiveling Angle
Detection Angle
TIME Adjustment
LUX adjustment
SENS adjustment
Mounting height
Switch Functions
Led Light Adjustments
Adjustable Angle
SUPPORT
For all product related questions, please contact: support@quintezz.com or check
our website www.quintezz.com for more information.
GUARANTEE
Copyright © Quintezz. Quintezz
®
Quintezz
brand stands for superior quality products and excellent customer ser-
®
vice. Therefore Quintezz
warrants this product to be free from defects in materials
®
and workmanship for a period of two (2) years from the original purchase date of the
product. The terms of this guarantee and the extent of responsibility of Quintezz
under this warranty can be downloaded from the website: www.quintezz.com.
TIME
About
about
10 seconds
7 minutes
10 seconds
7 minutes
SENS
Detects all
Detects all
motion
within 12m
within 5m
Passive infrared
220 ~240 V / 50~60 Hz
Max. 20W LED
600 mA
H05RN-F, 3G, 1.0 mm²
Class I
IP65
-20° C to + 40°C
<12M at 20° C
Horizontal 330°
Vertical 30°
110°
From 10 +- 3 sec .to 7 +- 2 minutes
3-2000 LUX
5~12 m
2,5~3.8m
SENS, TIME & LUX
Vertical 180 °
is a registered trademark of TE-Group NV. The
TIME
About
about
LUX
SENS
motion
®
Advertisement
