Lantronix xSenso 21R2 Quick Start Manual

xSenso
xSenso 21R2 Quick Start Guide
™
WHAT'S
WHAT'S xSenso 21A2 Quick Start Guide ™
WHAT'S INSIDE ™ Quick Start Guide 21A2 Quick Start Guide WHAT'S INSIDE xSenso xSenso™ 21A2 Wall Mount Bracket
1 HARDWARE REVIEW 9-30VDC Barrel Locking Power Input Rubber Feet (4)
INSIDE xSenso™ device Mini USB Port (Auto-MDIX) Ethernet port 10/100 Mbps For management and configuration of Output 2 Output 1 and Analog Input 2 I = 0-20mA Input Voltage V = ±100mV, ±1V, ±10V Input Current Input 1 Analog Block Power Input 9-30VDC Terminal
Reset pin Input 1 and Input 2 status LED status LED P = 15VDC, 10mA per channel or 20mA total = Ground Excitation
Analog Output 1 Analog Output Current I = 0-20mA = Ground Output 2 Output Voltage V = 0-10V
DIN Rail Mount hook onto the DIN rail, then push it 1. Angle the xSenso™ to position and 2 HARDWARE INSTALLATION 1. Place xSenso™ upside down on a smooth, flat surface. Desktop, shelf, or table top installation
to unlatch and remove. Angle and lift the xSenso™ upwards orange clip downward to unlock. 2. To remove from DIN rail, pull the secure. rail. Push the orange clip upwards to back until it is flat against the DIN adhesive-side down onto each corner of the xSenso device. 3. Turn the xSenso™ over so that it is resting on the rubber feet. 2. Peel off the rubber feet from the adhesive strip and place them
Quick Start Guide xSenso™ 21R2 Wall Mount Bracket
Rubber Feet (4)
1 HARDWARE REVIEW
9-30VDC Barrel Locking Power Input
INSIDE
Mini USB Port
For management Analog Analog 9-30VDC Terminal
Input 2 Input 1 Block Power Input
and configuration of
xSenso™ device
Input Current I = 0-20mA
Input Voltage V = ±100mV, ±1V, ±10V
10/100 Mbps Excitation P = 15VDC, 10mA per channel or 20mA total
Output 1 and
(Auto-MDIX) = Ground
Ethernet port Output 2
status LED
Input 1 and
Input 2
Reset pin status LED
Relay 1 Relay 2
NO = Normally Open
NC = Normally Closed
COM = Common Ground
2 HARDWARE INSTALLATION
DIN Rail Mount Desktop, shelf, or table top installation
1. Angle the xSenso™ to position and 1. Place xSenso™ upside down on a smooth, flat surface.
hook onto the DIN rail, then push it 2. Peel off the rubber feet from the adhesive strip and place them
back until it is flat against the DIN adhesive-side down onto each corner of the xSenso™ device.
rail. Push the orange clip upwards to
secure. 3. Turn the xSenso™ over so that it is resting on the rubber feet.
2. To remove from DIN rail, pull the
orange clip downward to unlock.
Angle and lift the xSenso™ upwards
to unlatch and remove.
Quick Start Guide
1 HARDWARE REVIEW
Mini USB Port
For management
and configuration of
xSenso™ device
10/100 Mbps
(Auto-MDIX)
Ethernet port
Reset pin
2 HARDWARE INSTALLATION
DIN Rail Mount
1. Angle the xSenso™ to position and
hook onto the DIN rail, then push it
back until it is flat against the DIN
rail. Push the orange clip upwards to
secure.
2. To remove from DIN rail, pull the
orange clip downward to unlock.
Angle and lift the xSenso™ upwards
to unlatch and remove.
21R2 Quick Start Guide
™
xSenso™ 21R2
Output 1 and
Output 2
status LED
Input 1 and
Input 2
status LED
Wall Mount Bracket
9-30VDC Barrel Locking Power Input
Analog Analog
Input 2 Input 1
Input Current I = 0-20mA
Input Voltage V = ±100mV, ±1V, ±10V
Excitation P = 15VDC, 10mA per channel or 20mA total
= Ground
Relay 1
NO = Normally Open
NC = Normally Closed
COM = Common Ground
Desktop, shelf, or table top installation
1. Place xSenso™ upside down on a smooth, flat surface.
2. Peel off the rubber feet from the adhesive strip and place them
adhesive-side down onto each corner of the xSenso™ device.
3. Turn the xSenso™ over so that it is resting on the rubber feet.
Rubber Feet (4)
9-30VDC Terminal
Block Power Input
Relay 2