Ex-Or SceneSelect II SMD810 Instruction Manual

Mixed dimmer

Advertisement

SceneSelect II
Scene-setting and Dimming System
SMD810
MIXED DIMMER
Warning ............................................................. 2
Features ............................................................ 2
Important Safeguards ........................................ 2
Internal View ................................................... ...3
Mounting ............................................................ 4
Supply & Load Cable Connections .................... 5
Tel: 01942 719229 Fax: 01942 272767 Email: technicalsales.ex-or@honeywell.com
Instruction Manual
Haydock Lane, Haydock, Merseyside WA11 9UJ
www.ex-or.com
Contents
Connecting Serial Control Cables...................... 6
Hardware Controls ............................................ 7
Dimmable Lamps Chart .................................... 7
Troubleshooting................................................. 9
Specification ..................................................... 9
Ex-Or
W4386A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SceneSelect II SMD810 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ex-Or SceneSelect II SMD810

  • Page 1: Table Of Contents

    Internal View ............3 Changing Scenes Using The Program Key ..8 Mounting ............4 Troubleshooting..........9 Supply & Load Cable Connections ....5 Specification ............. 9 Ex-Or Haydock Lane, Haydock, Merseyside WA11 9UJ Tel: 01942 719229 Fax: 01942 272767 Email: technicalsales.ex-or@honeywell.com www.ex-or.com...
  • Page 2: Warning

    ‘basic’ mode unless programmed via a THIS DEVICE MUST BE EARTHED. computer. Should programming be required, INSTALLATION, PROGRAMMING AND contact Ex-Or for details. Once the data cable is MAINTENANCE MUST BE CARRIED OUT BY QUALIFIED PERSONNEL. connected to the device(s), the factory default settings will allow any control panel to control all channels in all dimmers.
  • Page 3: Internal View

    Internal View Entry Gland Plate for Load Cables Circuit Breakers and Emergency Lighting Line Outputs Dimmed or Switched 230V Outputs 40A Single Phase Supply Connections 4 x Side Entry Gland Knockouts DALI Broadcast, 1-10V or DSI Control Ouputs Earth Link Accessory Port SceneSelect Bus Terminations...
  • Page 4: Mounting

    Mounting Select a suitable location CABLE TRAY OR This device is designed for indoor use only. If OTHER OBJECT installing in an external location, the device must be housed in a suitable well-ventilated 200mm MINIMUM GAP RISING HEAT enclosure. Choose a dry location, that will be accessible after the installation is complete.
  • Page 5: Supply & Load Cable Connections

    Supply & Load Cable Connections Supply Cables 1. Supply Terminals The supply input terminals are located toward the middle of the enclosure and consist of Earth, Neutral, 2. Emergency Lighting Terminals and Live, all of which will accept up to 10mm cables. 3.
  • Page 6: Connecting Serial Control Cables

    Connecting Serial Control Cables SceneSelect Bus Cable Connections There is one bus port in the form of an RJ12 socket on the front panel. This is used for the t e m p o r a r y c o n n e c t i o n o f a P C f o r RJ12 Socket Connections programming purposes.
  • Page 7: Hardware Controls

    Hardware Controls AUX Input - This is a dry contact interface that is active low. The dry contact is connected between the AUX and GND terminals on the SceneSelect bus connector strip. The function of the AUX input is programmable. Ensure that the cable length between the dry contact and terminal strip is no longer than 2 metres.
  • Page 8: Changing Scenes Using The Program Key

    Changing Presets Using The Program Key STEP 1: Select Preset to be changed by pushing buttons 1–4. The button LED will indicate current scene. STEP 2: Hold down the PROGRAM button for approximately five seconds, and then release it. All scene buttons will be flashing. STEP 3: To increase or decrease the brightness of all channels at the same time press the up, down or off button until the required...
  • Page 9: Troubleshooting

    Troubleshooting Check the following list. If you are still unable to rectify the situation, contact Ex-Or. Please ensure that you have completed the following prior to calling our technical support department. Check all symptoms in the Troubleshooting list Check for any deviations between the installation and the installation instructions...
  • Page 10 Notes...

Table of Contents