Advertisement
Available languages
Available languages
1/4" VGA IP PTZ Dome Colour Camera CCID1410-ST
Package contents
•
1 x 1/4" VGA IP PTZ-dome
•
1 x Documentation CD
•
1 x Utilities CD
•
1 x Installation instruction (English, German)
•
1 x Installation instruction (French, Spanish, Italian)
•
1 x SD card with case (2 GB)
•
3 x Wall plugs
•
3 x Mounting screw
•
1 x Mounting template for installation
•
1 x Mounting plate
Target readers
The instructions in this document are designed only for the
following target readers:
Installer
Qualification Activity
Condition of the
product
Technical
Installs the product,
Components of the
training for
individual
product are not yet
electrical
components of the
installed or need to be
installations.
product or
replaced or modified.
replacement parts.
General safety precautions
•
Read the general safety precautions before installing,
configuring and operating the device.
•
Keep this document for reference.
•
Always pass this document on together with the product.
•
Please also take into account any additional country-
specific, local safety standards or regulations concerning
project planning, operation and disposal of the product.
•
Follow all warnings and instructions marked on the
device.
•
Do not attempt to service or modify this device yourself.
Refer this work to qualified service personnel.
Liability claim
•
Do not make any changes or modifications to the device
unless they have been approved by the manufacturer.
•
Use only spare parts and accessories that have been
approved by the manufacturer.
Installation
•
It is recommended that all preparatory work (e.g. fitting of
accessories) be carried out in a workshop prior to final
installation.
Radio interference with other devices in the environment
•
When handling modules that are susceptible to
electrostatic discharge, please observe the ESD
guidelines.
Damage due to unsuitable mounting location
•
The environmental conditions recommended by the
manufacturer must be observed. See section
Specifications.
•
Do not operate the device in dusty places.
•
Do not expose the device to mechanical vibrations or
shocks.
•
Protect the device against moisture.
•
Place the unit on a stable surface that will hold its weight.
•
The mounting surface must be solid and non-
combustible.
•
Do not operate the device close to sources of powerful
electromagnetic radiation.
Danger of electrical shock due to incorrect connection
•
Connect the device only to power sources with the
specified voltage. Voltage supply requirements can be
found on the mains adapter.
•
Make sure the device is permanently connected to the
electricity supply; a readily accessible disconnect device
must be provided.
•
This device is designed to work with 24 V AC-systems or
PoE. Do not connect the device to any other power
systems
Transportation
•
Keep the packaging material for future transportation.
•
Do not expose the device to mechanical vibrations or
shocks
2
Siemens Building Technologies
Fire Safety & Security Products
Ordering Data
Type
Item Number
Description
CCID1410-ST S54561-C82-A1
MJPEG/MPEG-4 IP Colour
PTZ Dome Camera,
24 V AC, 50 Hz or PoE
CCID1410-AB S54561-B202-A1 Adapter for CCDA
Accessories
Installing the camera
Mounting on a ceiling
Note: Check if the ceiling structure and material have
a sufficient strength before installing the camera onto a
ceiling. If the amounting strength is inadequate, the
camera will fall, potentially causing an injury or a
camera failure.
1.
Paste the mounting template (1) on a ceiling.
2.
Make a hole in the ceiling where the camera is to be
installed to insert the power cable, LAN cable and other
cables.
3.
Feed all cables through the ceiling hole and the mounting
template hole.
4.
Fix the mounting plate (1) below the hole by using the
included wall plugs and mounting screws.
5.
Tie the safety wire (2) of the mounting plate (1) onto the
safety hook (3) of the camera.
6.
Align the camera grooves with the mounting plate (1).
7.
Push up the camera onto the mounting plate (1) and then
slide the camera back until the security hooks lock.
Connecting the cable
1.
Remove the terminal cover (5).
2.
For configuration and operation of the camera via
Ethernet, connect the network cable to the RJ45 terminal
(12) using a hub or a switch.
3.
Connect the control input to the terminals GND and AL IN
(15).
4.
Connect the AC Power on the camera.
•
For 24 V AC: Connect 24 V (~) cables to terminals
~AC 24 V (13).
•
For PoE: Connect the network cable to the RJ45
terminal (12) using a hub or a switch.
Caution: Incorrect connection may cause malfunction
and/or damage to the camera.
5.
Attach the terminal cover (5). (The terminal cover has the
function to prevent coming off of the AC power cable and
other cables.)
Setting camera parameters
Camera parameters can be modified through the IP
connection. You can follow the user manual of CCID1410-ST
for the IP function and parameter setting.
Presetting of camera position
The presets function of the camera enables you to assign up
to 64 different positions and names for the camera.
Pan/Tilt operation
•
Automatic Patrol can be set.
•
Automatic scanning can be set.
•
A PAN/TILT operation range of the camera can be set.
•
Camera can be set the Left/Right limit position
IP connection
Connect the Ethernet connector with an RJ45 cable, then
follow the user manual of CCID1410-ST for the IP function.
If direct connection to a PC network card is required, a cross-
over LAN cable should be used.
Care and maintenance
The camera is maintenance-free. Small amounts of dirt or
dust can be cleaned from the camera using a clean soft cloth.
•
Do not touch the lens area. Use a soft cloth moistened
with alcohol to clean the surface if it is touched
accidentally.
Update
For the latest camera firmware update, please refer to
the following download link:
http://www.siemens.com/cctv
Specifications
Image sensor
1/4"
Effective pixels
330K pixels, 640 (H) x 480 (V)
Image compression
MJPEG / MPEG4
method
Resolution
MJPEG: VGA (640 x 480) /
QVGA, (320 x 240) at 30 ips
MPEG4: VGA (640 x 480) /
QVGA, (320 x 240 ) at 30 ips
Min. Illumination
0.7 lux (1/30s F1.8 AGC max.)
Lens
F = 1.8 to 2.9, f: 4.2 – 42 mm, 10x
Pan travel
-175 to +175°
Pan speed
Max. 300 °/s (at preset)
Tilt range
Desktop: -30 to + 90°
Ceiling: -90 to +30°
Tilt speed
Max. 200 °/s (at preset)
Synchronisation
Internal
Network connection
RJ45, 1 x 10/100 based-T Ethernet
connection for LAN/WAN
TCP/IP, UDP, HTTP, SMTP, DNS,
Internet protocols
DHCP, NTP, ARP, ICMP, FTPc, FTPs,
DDNS, RTP (RTCP, RTSP), IGMP v3,
UPnP, NFS, CIFS
Power requirement
24 V AC, PoE
Power consumption
Max. 16 W
Camera weight
0.95 kg
Operating
0 to +50 °C
temperature
Disposal
Electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities
appointed by the government or the local
authorities.
EN
03.2009
Advertisement
