Subscribe to Our Youtube Channel
Related Manuals for IQCCTV IQC1920S2
Summary of Contents for IQCCTV IQC1920S2
- Page 1 HD SDI Full HD 1080P HD-SDI Mini Speed Dome HD SDI HD SDI HD SDI 360° 2.25x IP66 1080 P High Speed Weatherproof Adjustable 1080P 2.25x Optical Pan & Tilt Rated Lens Real Time Zoom User Manual Version 1...
-
Page 2: Table Of Contents
Contents 1. Product Overview ..............1.1. Product Features ........... 2. Product Contents ..............3. Protocol & Baud Rate ............4. Installation ................5. Camera Operation .............. 5.1. Set Preset Position ........5.2. Set Cruise Tracks, Transfer & Delete ... 5.3. Set Auto Scanning, Transfer & Stop ..... 6. - Page 3 Warning Caution: To prevent electric shock and fire hazards, please don’t use a power supply not Warning: To reduce the risk of listed in the manual. electric shock, non-professional personnel should not remove the cover. This symbol alerts the user to operate and maintain the product according to the manual.
-
Page 4: Product Overview
The dome is ideal for indoor or outdoor use (IP66 Rated) and has a cable managed and compact design. The IQC range of HD-SDI cameras from IQCCTV are designed to offer crystal clear images and amazing value for money. -
Page 5: Product Contents
2. Product Contents Before installing this product, please ensure that it contains the following; Contents 1x IQC1920S2 Speed Dome Camera HD SDI Full HD 1080P HD-SDI Mini Speed Dome 1x User Manual IP66 1920x1080P 2x Optical Weatherproof Wide Angle Resolution... -
Page 6: Protocol & Baud Rate
3. Protocol & Baud Rate Please check the protocol and baud rate before installing the speed dome. To match up the switcher identities please follow the steps below; 1. Open up the inner case of the speed dome by loosening the screws on the cover. - Page 7 3. Set the Baud Rate To set the baud rate, adjust the DIP switch to any of the combinations below to match your preferred settings. Switcher Switcher Baudrate Baudrate Status Status 4. Set the protocol and camera model The camera will auto detect Pelco P or Pelco D, the below is for camera model which does not need to be changed.
- Page 8 5. Set the Dome IP Address The table below shows how to adjust the DIP switch to set the camera’s ID. Switcher Switcher Switcher Address Address Address...
- Page 9 Switcher Switcher Switcher Address Address Address Please Note: The factory default ID is 1 and the Baud Rate is 2400...
-
Page 10: Installation
4. Installation The IQC1920S2 is designed to be wall mounted using the cable managed bracket supplied. To install the camera, please follow the steps below. 1. Remove the bracket from the main 2. Using the bracket as a stencil, mark camera body by taking off the screws out the drill holes needed in the wall. - Page 11 5. Now, thread the cable from the main 6. Re-attach the main camera to the camera back through the bracket. bracket. To do this, use a cross head screw driver and turn screws in clockwise. 7. Lastly, screw the bracket into the wall.
-
Page 12: Camera Operation
5. Camera Operation The Speed Dome camera will be controlled through the DVR using the arrow keys etc. However, it is advised to use an external Speed Dome controller, for more control over the camera. 5.1 Set Preset Position Set the pan/tilt rotation range through the DVR and store the numbers in the Dome Camera. -
Page 13: Set Cruise Tracks, Transfer & Delete
5.2 Set Cruise Tracks, Transfer & Delete The Speed Dome camera allows the user to set a preset cruise so that the camera will pan through these presets without having to adjust the camera manually. The camera has 5 lines of auto cruise tracks and each line can store a minimm of 16 presets up to a maximum of 64. -
Page 14: Set Auto Scanning, Transfer & Stop
5.3. Set Auto Scanning, Transfer & Stop The camera revolves on a 360° angle and can automatically scan in certain preset positions using the DVR or Speed Dome Controller. 1) Set Auto Scanning A) Move the dome to the left limit using the joystick. B) Press 62 C) Press ‘Set’... - Page 15 For example, set up the auto scanning function using the keyboard by inputting ‘84’ and pressing the ‘Call’ button. 4) Stop Auto Scanning Set the Preset position to 86 or move the joystick to stop auto scanning. For example, to stop scanning using the keyboard; A) Input 86 B) Press ‘Call’...
- Page 16 6) 360° Auto Scanning To begin auto scanning, press Auto. The set the scanning speed, please refer to section 5.3 on page 14. 7) Back to Preset Position The camera can set the preset position back to 1, even if nobody operates the camera.
-
Page 17: Osd Menu
6. OSD Menu The OSD menu allows the user alter the settings on the camera such as lens, Day & Night mode,RS485 settings and reset the camera to the factory default. To enter into the menu, press the ‘Open’ or ‘IRIS+’... -
Page 18: White Balance
To enter into the submenu of BLC, press ‘Menu’ button. Here, you can setup: GAIN: Set the Backlight area, High, Middle or Low AREA: Select the BLC area and the compensation area size after entering the ‘Area’ menu. DEFAULT: Choose to go back to the default setting. Sub-menu of HSBLC. -
Page 19: Day & Night
6.4 Day & Night Select Day & Night and press the ‘Menu’ button to setup Day & Night mode and to setup Smart NR. You can choose between Auto , Colour, B/W or External. Sub-Menu of Auto. Here you can set the delay time between Day & Night mode. - Page 20 D-Effect: Setting of digital functions. Press the ‘Menu’ button to enter into the sub-menu. Sub-Menu of D-Effect. This allows you to set the following functions. Freeze: Set the freeze function to on or off. Mirror: Set the mirror function mirror, V-flip or rotate. D-Zoom: Set the digital zoom function.
-
Page 21: Adjust
Defect: Turn this function off to correct any dead pixels. When this is turned on you will enter into a sub-menu. Sub-Menu of Defect will allow you to set the following: Live DPC: Live dead pixel correction, turn this function on or off. Level: Set the sensitivity level of the live correction function (0-60) Static DPC: Static dead pixel correction function, turn this function on or off. -
Page 22: Reset
OSD: Set the OSD menu characteristics. Sub-Menu of OSD allows you to adjust the following: Text Colour: Adjust the OSD menu text colour. 8 colours are selectable Outline: Set the character outline, either on or off. LSC: Turn the lens edge correction function on or off. NTSC/PAL: Set the signal system setting either NTSC or PAL. -
Page 23: Troubleshooting
7. Troubleshooting Trouble Shooting Problem Possible Cause Solution Power Supply Damage Change the PSU Change the Incorrect Connection No Picture Connections Damage to the Wiring Check the Wiring Wrong connection of control Check the Wiring Successful Camera signals test but still no image Camera is Damaged Replace the Camera... - Page 24 (including accidental damage) and damage caused by normal wear and tear. In the unlikely event that you encounter a problem with this product, it should be returned to the place of purchase. IQCCTV, Unit 2 Valley Point, Beddington Farm Road, Croydon, Surrey CR0 4WP www.iqcctv.co.uk...
Need help?
Do you have a question about the IQC1920S2 and is the answer not in the manual?
Questions and answers