Advertisement
Figure 5 Gigabit Ethernet Port Pin-Out
Signal Name
Function
RJ-45 Female
Pin-Out
BI_DA+
Bi-directional pair +A
1
BI_DA-
Bi-directional pair -A
2
3
BI_DB+
Bi-directional pair +B
4
BI_DC+
Bi-directional pair +C
5
BI_DC-
Bi-directional pair -C
6
BI_DB-
Bi-directional pair -B
7
BI_DD+
Bi-directional pair +D
8
BI_DD-
Bi-directional pair -D
Serial Console Port
The serial console port (Console) allows you to connect the IAP to a serial terminal or
a laptop for direct local management. This port is an RJ-45 female connector with the
pinouts described in
Figure
6. Connect this port in one of the following ways:
Connect it directly to a terminal or terminal server using an Ethernet cable.
Use a modular adapter to convert the RJ-45 (female) connector on the IAP to a
DB-9 (male) connector, and connect the adapter to a laptop using an RS-232
cable. See
Figure 7
for connector details of the adapter.
Figure 6 Serial Port Pin-Out
Serial
RJ-45 Female
Console Port
Pin-Out
1
2
3
TxD
4
GND
5
GND
6
RxD
7
8
Direction
Input
Output
Figure 7 RJ-45 (Female) to DB-9 (Male) Modular Adapter Conversion
RJ-45 Female
Internal
DB-9 Male
Pin-Out
Connections
Pin-Out
1
RJ-45
DB-9
2
3
3
2
5
Ground
TxD
TxD
9
4
4
4
8
5
3
RxD
GND
5
5
GND
7
2
6
6
3
TxD
RxD
RxD
6
1
7
8
Direction
Direction
Input
Input
Output
Output
Power Connection
The W-IAP100 Series has a single 12V DC power jack socket to support powering
through an AC-to-DC power adapter.
Note: If both POE and DC power are available, the IAP uses POE even when there
is not enough POE voltage available to power the IAP.
Verifying Post-Installation Connectivity
The integrated LEDs on the IAP can be used to verify that the IAP is receiving power
and initializing successfully (see
Table
1). Refer to the Dell PowerConnect W-Series
W-Instant Quick Start Guide for further details on verifying post-installation network
connectivity.
Table 1 W-IAP100 Series LED Behavior
LED
Color/State
Meaning
PWR
Off
No power to IAP
Green flashing
System initializing
Red steady
System failed to initialize, contact TAC
Green steady
Power on, device ready
ENET
Off
No link
(10/100/1000 Mbps)
Green on
1000 Mbps link
Amber on
10/100 Mbps link
Green flashing
Ethernet link activity
11A/N
Off
5 GHz radio is disabled
Amber
5 GHz radio enabled in WLAN mode
Green
5 GHz radio enabled in 11n mode
Green flashing
5 GHz Air Monitor or RF Protect mode
11B/G/N
Off
2.4 GHz radio disabled
Amber
2.4 GHz radio enabled in WLAN mode
Green
2.4 GHz radio enabled in 11n mode
Green flashing
2.4 GHz Air Monitor or RF Protect mode
Product Specifications
Electrical
Ethernet:
1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces
MDI/MDX
IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T),
IEEE 802.3ab (1000Base-T)
Power over Ethernet (IEEE 802.3af compliant), 48V DC/350mA
Power:
12 VDC power interface, supports powering through an AC-to-DC power
adapter
Note: If a power adapter other than the one provided by Dell is used in the US or
Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum
1.25A, marked "LPS" or "Class 2," and suitable for plugging into a standard power
receptacle in the US and Canada.
For additional specifications on this product, please refer to the data sheet. The data
sheet can be found at dell.com/wireless.
Proper Disposal of Dell Equipment
For the most current information about Global Environmental Compliance and Dell
products, see our website at dell.com.
China RoHS
Dell products also comply with China environmental declaration
requirements and are labeled with the "EFUP 10" label shown at the
10
left.
Hazardous Materials Declaration
(Hazardous Substance)
(Parts)
PCA Boards)
Mechanical Sub-Assemblies)
SJ/T11363-2006
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
Waste of Electrical and Electronic Equipment
Dell products at end of life are subject to separate collection and
treatment in the EU Member States, Norway, and Switzerland and
therefore are marked with the symbol shown at the left (crossed-out
wheelie bin). The treatment applied at end of life of these products
in these countries shall comply with the applicable national laws of
countries implementing Directive 2002/96EC on Waste of Electrical
and Electronic Equipment (WEEE).
European Union RoHS
Dell products also comply with the EU Restriction of
Hazardous Substances Directive 2002/95/EC (RoHS). EU
RoHS restricts the use of specific hazardous materials in the
manufacture of electrical and electronic equipment. Specifically, restricted materials
under the RoHS Directive are Lead (including Solder used in printed circuit
assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Dell
products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in
solder used in printed circuit assemblies). Products and packaging will be marked
with the "RoHS" label shown at the left indicating conformance to this Directive.
Safety and Regulatory Compliance
Dell provides a multi-language document that contains country-specific restrictions
and additional safety and regulatory information for all Dell hardware products. The
Dell PowerConnect W-Series Safety, Environmental, and Regulatory Information
document is included with this product.
The device is electronically labeled and the FCC ID will be displayed via the WebUI
under the About menu.
Caution: RF Radiation Exposure Statement: This equipment complies with FCC RF
radiation exposure limits. This equipment should be installed and operated with a
minimum distance of 13.78 inches (35 cm) between the radiator and your body for 2.4
GHz and 5 GHz operations. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25
GHz frequency range, this device is restricted to indoor use to reduce the potential for
harmful interference with co-channel Mobile Satellite Systems.
EMC Compliance and Warning Statement
IEC 60601-1-2: 2007
EN 60601-1-2: 2007
The W-IAP105 has been tested and found to comply with the limits of the standard
for medical devices, IEC 60601-1-2:2007. The unit also complies with the
requirements of EN 60601-1-2:2007, providing the presumption of compliance to the
European Union's Medical Device Directive 2007/47/EC. The limits are designed to
provide reasonable protection against harmful interference in a typical medical
installation. This equipment generates, uses and can radiate radio frequency energy,
and, if not installed and used in accordance with the manufacturer's instructions may
cause harmful interference to other devices in the vicinity. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment causes interference with other devices, which may be determined by
turning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
Reorient or relocate the device receiving the interference.
Increase the separation between the equipment.
Connect the equipment into an outlet on a circuit different from that to which
the other device(s) are connected.
Consult the manufacturer or field service technician for help.
The Model W-IAP105 do not have an Applied Part as defined in IEC 60601-1. The
protection against electric shock is Class ll.
Device is not protected against ingress of liquids and has a protection class of IPX0 as
defined by IEC 60601-1 and IEC 60529. Equipment not suitable for use in the
presence of flammable mixtures.
The unit is considered "Continuous Operation" equipment as defined by IEC 60601-1.
Power Consumption – 48 VDC 802.3af power over Ethernet or 12VDC, 1.25A for
external AC supplied power (adapter sold separately); Maximum power consumption
– 12.5W.
Mechanical Dimensions: 132mm x 135mm x 45mm; 300g.
Environmental: Operating Temp: 0° C to +50° C (+32° F to +122° F); Humidity: 5
to 95% non-condensing. Storage Temp: -40° CS to +70° C (-40°F to +158°F).
Singapore
200202320G
UAE
TRA
TRA
REGISTERED No:
REGISTERED No:
0019614/09
ER0090445/12
DEALER No:
DEALER No:
DA0039425/10
DA0039425/10
Indonesia
21894/SDPPI/2011
25268/SDPPI/2012
1912
1912
Philippines (W-IAP105)
Type-Approval No.
ESD-CPE-1004517C
Dell PowerConnect W-IAP100
Series Instant Access Point
Installation Guide
Contacting Support
Web Site Support
Main Site
dell.com
Support Site
support.dell.com
Dell Documentation
support.dell.com/manuals
Copyright
© 2012 Aruba Networks, Inc. Aruba Networks trademarks include
, Aruba Networks
®
Aruba Wireless Networks
, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility
®
Management System
. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc.
All rights reserved. Specifications in this manual are subject to change without notice.
Originated in the USA. All other trademarks are the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code
subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open
Source Licenses. The Open Source code used can be found at this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate
other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for
this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against
it with respect to infringement of copyright on behalf of those vendors.
www.dell.com
Dell PowerConnect W-IAP100 Series Instant Access Point | Installation Guide
Part Number 0511154-01 | July 2012
®
,
Advertisement
